IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
Other implementations of .*get_drvinfo use strscpy so this patch brings
lan78xx_get_drvinfo() in line as well:
igb/igb_ethtool.c +851
static void igb_get_drvinfo(struct net_device *netdev,
igbvf/ethtool.c
167:static void igbvf_get_drvinfo(struct net_device *netdev,
i40e/i40e_ethtool.c
1999:static void i40e_get_drvinfo(struct net_device *netdev,
e1000/e1000_ethtool.c
529:static void e1000_get_drvinfo(struct net_device *netdev,
ixgbevf/ethtool.c
211:static void ixgbevf_get_drvinfo(struct net_device *netdev,
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231012-strncpy-drivers-net-usb-lan78xx-c-v1-1-99d513061dfc@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c55 ("bpf: Fix verifier log for async callback return values")
a923819fb2c5 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A bulk transfer of the USB may contain many packets. And, the total
number of the packets in the bulk transfer may be more than budget.
Originally, only budget packets would be handled by napi_gro_receive(),
and the other packets would be queued in the driver for next schedule.
This patch would break the loop about getting next bulk transfer, when
the budget is exhausted. That is, only the current bulk transfer would
be handled, and the other bulk transfers would be queued for next
schedule. Besides, the packets which are more than the budget in the
current bulk trasnfer would be still queued in the driver, as the
original method.
In addition, a bulk transfer wouldn't contain more than 400 packets, so
the check of queue length is unnecessary. Therefore, I replace it with
WARN_ON_ONCE().
Fixes: cf74eb5a5bc8 ("eth: r8152: try to use a normal budget")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230926111714.9448-433-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e4454 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
The D-Link DUB-E250 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Antonio Napolitano <anton@polit.no>
Link: https://lore.kernel.org/r/CV200KJEEUPC.WPKAHXCQJ05I@mercurius
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mario reports that loading r8152 on his system leads to a:
netif_napi_add_weight() called with weight 256
warning getting printed. We don't have any solid data
on why such high budget was chosen, and it may cause
stalls in processing other softirqs and rt threads.
So try to switch back to the default (64) weight.
If this slows down someone's system we should investigate
which part of stopping starting the NAPI poll in this
driver are expensive.
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/all/0bfd445a-81f7-f702-08b0-bd5a72095e49@amd.com/
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230814153521.2697982-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need for two more variables in hso_serial_write(). Switch to
min_t() and eliminate those.
Furthermore, the 'if-goto' is superfluous as memcpy() of zero count is a
nop. So is addition of zero. So remove the 'if-goto' completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20230810091510.13006-36-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632
Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.")
Signed-off-by: Ross Maynard <bids.7405@bigpond.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The timer dev->stat_monitor can schedule the delayed work dev->wq and
the delayed work dev->wq can also arm the dev->stat_monitor timer.
When the device is detaching, the net_device will be deallocated. but
the net_device private data could still be dereferenced in delayed work
or timer handler. As a result, the UAF bugs will happen.
One racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_stat_monitor() |
... | lan78xx_disconnect()
lan78xx_defer_kevent() | ...
... | cancel_delayed_work_sync(&dev->wq);
schedule_delayed_work() | ...
(wait some time) | free_netdev(net); //free net_device
lan78xx_delayedwork() |
//use net_device private data |
dev-> //use |
Although we use cancel_delayed_work_sync() to cancel the delayed work
in lan78xx_disconnect(), it could still be scheduled in timer handler
lan78xx_stat_monitor().
Another racy situation is shown below:
(Thread 1) | (Thread 2)
lan78xx_delayedwork |
mod_timer() | lan78xx_disconnect()
| cancel_delayed_work_sync()
(wait some time) | if (timer_pending(&dev->stat_monitor))
| del_timer_sync(&dev->stat_monitor);
lan78xx_stat_monitor() | ...
lan78xx_defer_kevent() | free_netdev(net); //free
//use net_device private data|
dev-> //use |
Although we use del_timer_sync() to delete the timer, the function
timer_pending() returns 0 when the timer is activated. As a result,
the del_timer_sync() will not be executed and the timer could be
re-armed.
In order to mitigate this bug, We use timer_shutdown_sync() to shutdown
the timer and then use cancel_delayed_work_sync() to cancel the delayed
work. As a result, the net_device could be deallocated safely.
What's more, the dev->flags is set to EVENT_DEV_DISCONNECT in
lan78xx_disconnect(). But it could still be set to EVENT_STAT_UPDATE
in lan78xx_stat_monitor(). So this patch put the set_bit() behind
timer_shutdown_sync().
Fixes: 77dfff5bb7e2 ("lan78xx: Fix race condition in disconnect handling")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA_BP_0 ~ PLA_BP_15 (0xfc28 ~ 0xfc46) are continuous registers, so we
could combine the control transfers into one control transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-419-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce the control transfer if all bytes of first or the last DWORD are
written.
The original method is to split the control transfer into three parts
(the first DWORD, middle continuous data, and the last DWORD). However,
they could be combined if whole bytes of the first DWORD or last DWORD
are written. That is, the first DWORD or the last DWORD could be combined
with the middle continuous data, if the byte_en is 0xff.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230726030808.9093-418-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add CDC-ECM support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RmNet support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230626125336.3127-1-davide.tronchin.94@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/mlx5/driver.h
617f5db1a626 ("RDMA/mlx5: Fix affinity assignment")
dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
https://lore.kernel.org/all/20230613125939.595e50b8@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
47867f0a7e83 ("selftests: mptcp: join: skip check if MIB counter not supported")
425ba803124b ("selftests: mptcp: join: support RM_ADDR for used endpoints or not")
45b1a1227a7a ("mptcp: introduces more address related mibs")
0639fa230a21 ("selftests: mptcp: add explicit check for new mibs")
https://lore.kernel.org/netdev/20230609-upstream-net-20230610-mptcp-selftests-support-old-kernels-part-3-v1-0-2896fe2ee8a3@tessares.net/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move declarations into include/net/gso.h and code into net/core/gso.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230608191738.3947077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This module has for a long time not been limited to iPhone <= 3GS.
Update description to match the actual state of the driver.
Remove dead link from 2010, instead reference an existing userspace
iOS device pairing implementation as part of libimobiledevice.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent iOS releases support CDC NCM encapsulation on RX. This mode is
the default on macOS and Windows. In this mode, an iOS device may include
one or more Ethernet frames inside a single URB.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver. When reconnecting such a device
from a macOS/Windows machine to a Linux host, the device stays in
NCM mode, making it unusable with the legacy ipheth driver code.
To correctly support such a device, the driver has to either support
the NCM mode too, or put the device back into legacy mode.
To match the behaviour of the macOS/Windows driver, and since there
is no documented control command to revert to legacy mode, implement
NCM support. The device is attempted to be put into NCM mode by default,
and falls back to legacy mode if the attempt fails.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behaviour of the official iOS tethering driver on macOS is to not
transmit any trailing padding at the end of URBs. This is applicable
to both NCM and legacy modes, including older devices.
Adapt the driver to not include trailing padding in TX URBs, matching
the behaviour of the official macOS driver.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup precedure in ipheth_probe will attempt to free a
NULL pointer in dev->ctrl_buf if the memory allocation for
this buffer is not successful. While kfree ignores NULL pointers,
and the existing code is safe, it is a better design to rearrange
the goto labels and avoid this.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d3364f ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8a2 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The
r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx.
Otherwise, the coalescing settings are useless.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the poor throughput for 2.5G devices, when changing the speed from
auto mode to force mode. This patch is used to notify the MAC when the
mode is changed.
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The feature of flow control becomes abnormal, if the device sends a
pause frame and the tx/rx is disabled before sending a release frame. It
causes the lost of packets.
Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the
tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow
control patch and timer. Then, the hardware could clear the state and
the flow control becomes normal after enabling tx/rx.
Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto().
Fixes: 195aae321c82 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is a little tight on my system, it's pretty easy to see
warnings that look like this.
ksoftirqd/0: page allocation failure: order:3, mode:0x40a20(GFP_ATOMIC|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
...
Call trace:
dump_backtrace+0x0/0x1e8
show_stack+0x20/0x2c
dump_stack_lvl+0x60/0x78
dump_stack+0x18/0x38
warn_alloc+0x104/0x174
__alloc_pages+0x588/0x67c
alloc_rx_agg+0xa0/0x190 [r8152 ...]
r8152_poll+0x270/0x760 [r8152 ...]
__napi_poll+0x44/0x1ec
net_rx_action+0x100/0x300
__do_softirq+0xec/0x38c
run_ksoftirqd+0x38/0xec
smpboot_thread_fn+0xb8/0x248
kthread+0x134/0x154
ret_from_fork+0x10/0x20
On a fragmented system it's normal that order 3 allocations will
sometimes fail, especially atomic ones. The driver handles these
failures fine and the WARN just creates spam in the logs for this
case. The __GFP_NOWARN flag is exactly for this situation, so add it
to the allocation.
NOTE: my testing is on a 5.15 system, but there should be no reason
that this would be fundamentally different on a mainline kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230406171411.1.I84dbef45786af440fd269b71e9436a96a8e7a152@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"modprobe asix ; rmmod asix ; modprobe asix" fails with:
sysfs: cannot create duplicate filename \
'/devices/virtual/mdio_bus/usb-003:004'
Issue was originally reported by Anton Lundin on 2022-06-22 (link below).
Chrome OS team hit the same issue in Feb, 2023 when trying to find
work arounds for other issues with AX88172 devices.
The use of devm_mdiobus_register() with usbnet devices results in the
MDIO data being associated with the USB device. When the asix driver
is unloaded, the USB device continues to exist and the corresponding
"mdiobus_unregister()" is NOT called until the USB device is unplugged
or unauthorized. So the next "modprobe asix" will fail because the MDIO
phy sysfs attributes still exist.
The 'easy' (from a design PoV) fix is to use the non-devm variants of
mdiobus_* functions and explicitly manage this use in the asix_bind
and asix_unbind function calls. I've not explored trying to fix usbnet
initialization so devm_* stuff will work.
Fixes: e532a096be0e5 ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/netdev/20220623063649.GD23685@pengutronix.de/T/
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20230321170539.732147-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
clang with W=1 reports
drivers/net/usb/plusb.c:65:1: error:
unused function 'pl_clear_QuickLink_features' [-Werror,-Wunused-function]
pl_clear_QuickLink_features(struct usbnet *dev, int val)
^
This static function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Additionally prevent integer underflow when size is less than
ETH_FCS_LEN.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230316101954.75836-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet length check needs to be located after size and align_count
calculation to prevent kernel panic in skb_pull() in case
rx_cmd_a & RX_CMD_A_RED evaluates to true.
Fixes: d8b228318935 ("net: usb: smsc75xx: Limit packet length to skb->len")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230316110540.77531-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
