IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a555 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac4792c
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b474 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
The driver currently raises the following sparse warning:
[...] cfg80211.c:360:42: warning: incorrect type in assignment (different
base types)
[...] cfg80211.c:360:42: expected unsigned int key_mgmt_suite
[...] cfg80211.c:360:42: got restricted __be32 [usertype]
CHECK drivers/net/wireless/microchip/wilc1000/netdev.c
This conversion was needed because historically the external supplicant
(observed with wpa_supplicant) expects AKM suite as big endian in
NL80211_CMD_EXTERNAL_AUTH message when the AKM suite is WLAN_AKM_SUITE_SAE.
This is not needed anymore:
- new (to be released) versions of wpa_supplicant now reads it in host
endian _while_ keeping compatibility for older drivers
- for new drivers used with current/old wpa_supplicant, this conversion has
been added to nl80211 to force big endian when the AKM suite is
WLAN_AKM_SUITE_SAE
Remove this not-needed-anymore conversion to fix the sparse warning.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308290615.lUTIgqUl-lkp@intel.com/
Tested-on: WILC1000 hwB SPI WILC_WIFI_FW_REL_16_1-13452
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240215-nl80211_fix_akm_suites_endianness-v1-2-57e902632f9d@bootlin.com
Some code manipulating the vif list is still missing some srcu_read_lock /
srcu_read_unlock, and so can trigger RCU warnings:
=============================
WARNING: suspicious RCU usage
6.8.0-rc1+ #37 Not tainted
-----------------------------
drivers/net/wireless/microchip/wilc1000/hif.c:110 RCU-list traversed without holding the required lock!!
[...]
stack backtrace:
CPU: 0 PID: 6 Comm: kworker/0:0 Not tainted 6.8.0-rc1+ #37
Hardware name: Atmel SAMA5
Workqueue: events sdio_irq_work
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from wilc_get_vif_from_idx+0x158/0x180
wilc_get_vif_from_idx from wilc_network_info_received+0x80/0x48c
wilc_network_info_received from wilc_handle_isr+0xa10/0xd30
wilc_handle_isr from wilc_sdio_interrupt+0x44/0x58
wilc_sdio_interrupt from process_sdio_pending_irqs+0x1c8/0x60c
process_sdio_pending_irqs from sdio_irq_work+0x6c/0x14c
sdio_irq_work from process_one_work+0x8d4/0x169c
process_one_work from worker_thread+0x8cc/0x1340
worker_thread from kthread+0x448/0x510
kthread from ret_from_fork+0x14/0x28
Fix those warnings by adding the needed lock around the corresponding
critical sections
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240215-wilc_fix_rcu_usage-v1-4-f610e46c6f82@bootlin.com
Enabling CONFIG_PROVE_RCU_LIST raises many warnings in wilc driver, even on
some places already protected by a read critical section. An example of
such case is in wilc_get_available_idx:
=============================
WARNING: suspicious RCU usage
6.8.0-rc1+ #32 Not tainted
-----------------------------
drivers/net/wireless/microchip/wilc1000/netdev.c:944 RCU-list traversed in non-reader section!!
[...]
stack backtrace:
CPU: 0 PID: 26 Comm: kworker/0:3 Not tainted 6.8.0-rc1+ #32
Hardware name: Atmel SAMA5
Workqueue: events_freezable mmc_rescan
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from wilc_netdev_ifc_init+0x788/0x8ec
wilc_netdev_ifc_init from wilc_cfg80211_init+0x690/0x910
wilc_cfg80211_init from wilc_sdio_probe+0x168/0x490
wilc_sdio_probe from sdio_bus_probe+0x230/0x3f4
sdio_bus_probe from really_probe+0x270/0xdf4
really_probe from __driver_probe_device+0x1dc/0x580
__driver_probe_device from driver_probe_device+0x60/0x140
driver_probe_device from __device_attach_driver+0x268/0x364
__device_attach_driver from bus_for_each_drv+0x15c/0x1cc
bus_for_each_drv from __device_attach+0x1ec/0x3e8
__device_attach from bus_probe_device+0x190/0x1c0
bus_probe_device from device_add+0x10dc/0x18e4
device_add from sdio_add_func+0x1c0/0x2c0
sdio_add_func from mmc_attach_sdio+0xa08/0xe1c
mmc_attach_sdio from mmc_rescan+0xa00/0xfe0
mmc_rescan from process_one_work+0x8d4/0x169c
process_one_work from worker_thread+0x8cc/0x1340
worker_thread from kthread+0x448/0x510
kthread from ret_from_fork+0x14/0x28
This warning is due to the section being protected by a srcu critical read
section, but the list traversal being done with classic RCU API. Fix the
warning by using corresponding SRCU read lock/unlock APIs. While doing so,
since we always manipulate the same list (managed through a pointer
embedded in struct_wilc), add a macro to reduce the corresponding
boilerplate in each call site.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240215-wilc_fix_rcu_usage-v1-2-f610e46c6f82@bootlin.com
Move netif_wake_queue and its surrounding RCU operations in a dedicated
function to clarify wilc_txq_task and ease refactoring
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240215-wilc_fix_rcu_usage-v1-1-f610e46c6f82@bootlin.com
Previously, the driver created a net device (typically wlan0) as soon
as the module was loaded. This commit changes the driver to follow
normal Linux convention of creating the net device only when bus
probing detects a supported chip.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Tested-By: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212202057.3468714-1-davidm@egauge.net
wilc_netdev_cleanup currently triggers a KASAN warning, which can be
observed on interface registration error path, or simply by
removing the module/unbinding device from driver:
echo spi0.1 > /sys/bus/spi/drivers/wilc1000_spi/unbind
==================================================================
BUG: KASAN: slab-use-after-free in wilc_netdev_cleanup+0x508/0x5cc
Read of size 4 at addr c54d1ce8 by task sh/86
CPU: 0 PID: 86 Comm: sh Not tainted 6.8.0-rc1+ #117
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x58
dump_stack_lvl from print_report+0x154/0x500
print_report from kasan_report+0xac/0xd8
kasan_report from wilc_netdev_cleanup+0x508/0x5cc
wilc_netdev_cleanup from wilc_bus_remove+0xc8/0xec
wilc_bus_remove from spi_remove+0x8c/0xac
spi_remove from device_release_driver_internal+0x434/0x5f8
device_release_driver_internal from unbind_store+0xbc/0x108
unbind_store from kernfs_fop_write_iter+0x398/0x584
kernfs_fop_write_iter from vfs_write+0x728/0xf88
vfs_write from ksys_write+0x110/0x1e4
ksys_write from ret_fast_syscall+0x0/0x1c
[...]
Allocated by task 1:
kasan_save_track+0x30/0x5c
__kasan_kmalloc+0x8c/0x94
__kmalloc_node+0x1cc/0x3e4
kvmalloc_node+0x48/0x180
alloc_netdev_mqs+0x68/0x11dc
alloc_etherdev_mqs+0x28/0x34
wilc_netdev_ifc_init+0x34/0x8ec
wilc_cfg80211_init+0x690/0x910
wilc_bus_probe+0xe0/0x4a0
spi_probe+0x158/0x1b0
really_probe+0x270/0xdf4
__driver_probe_device+0x1dc/0x580
driver_probe_device+0x60/0x140
__driver_attach+0x228/0x5d4
bus_for_each_dev+0x13c/0x1a8
bus_add_driver+0x2a0/0x608
driver_register+0x24c/0x578
do_one_initcall+0x180/0x310
kernel_init_freeable+0x424/0x484
kernel_init+0x20/0x148
ret_from_fork+0x14/0x28
Freed by task 86:
kasan_save_track+0x30/0x5c
kasan_save_free_info+0x38/0x58
__kasan_slab_free+0xe4/0x140
kfree+0xb0/0x238
device_release+0xc0/0x2a8
kobject_put+0x1d4/0x46c
netdev_run_todo+0x8fc/0x11d0
wilc_netdev_cleanup+0x1e4/0x5cc
wilc_bus_remove+0xc8/0xec
spi_remove+0x8c/0xac
device_release_driver_internal+0x434/0x5f8
unbind_store+0xbc/0x108
kernfs_fop_write_iter+0x398/0x584
vfs_write+0x728/0xf88
ksys_write+0x110/0x1e4
ret_fast_syscall+0x0/0x1c
[...]
David Mosberger-Tan initial investigation [1] showed that this
use-after-free is due to netdevice unregistration during vif list
traversal. When unregistering a net device, since the needs_free_netdev has
been set to true during registration, the netdevice object is also freed,
and as a consequence, the corresponding vif object too, since it is
attached to it as private netdevice data. The next occurrence of the loop
then tries to access freed vif pointer to the list to move forward in the
list.
Fix this use-after-free thanks to two mechanisms:
- navigate in the list with list_for_each_entry_safe, which allows to
safely modify the list as we go through each element. For each element,
remove it from the list with list_del_rcu
- make sure to wait for RCU grace period end after each vif removal to make
sure it is safe to free the corresponding vif too (through
unregister_netdev)
Since we are in a RCU "modifier" path (not a "reader" path), and because
such path is expected not to be concurrent to any other modifier (we are
using the vif_mutex lock), we do not need to use RCU list API, that's why
we can benefit from list_for_each_entry_safe.
[1] https://lore.kernel.org/linux-wireless/ab077dbe58b1ea5de0a3b2ca21f275a07af967d2.camel@egauge.net/
Fixes: 8399918f3056 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240212-wilc_rework_deinit-v1-1-9203ae56c27f@bootlin.com
Document
ATWILC1000/ATWILC3000
Baremetal Wi-Fi/BLE Link Controller Software Design Guide
https://tinyurl.com/yer2xhyc
says that bit 0 of the CRC7 code must always be a 1.
I confirmed that today with a logic analyzer: setting bit 0 causes
wilc1000 to accept a command with CRC7 enabled, whereas clearing bit 0
causes wilc1000 to reject the command with a CRC error.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240207050736.2717641-1-davidm@egauge.net
WILC driver currently applies some default configuration whenever the firmware
is initialized, and sets the default preamble size to short. However, despite
this passed option, firmware is also able to successfully connect to access
points only using long preamble, so this setting does not really enforce short
preambles and is misleading regarding applied configuration.
Update default configuration and make it match the firmware behavior by passing
the existing WILC_FW_PREAMBLE_AUTO value (2 instead of 0). The updated setting
does not really alter firmware behavior since it is still capable to connect to
both short preamble and long preamble access points, but at list the setting now
expresses for real the corresponding firmware behavior.
More info: it has been implemented to address the transmission (Tx) blackout
issue observed in the 802.11b mode. The modification has no impact on the other
modes, which will continue to work as they did in the previous implementation.
This change will allow the 802.11b transmission (2, 5.5, 11Mbps) to use long
preamble.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-1-54d29463a738@bootlin.com
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Calling spi_sync() unconditionally sets the spi field of struct
spi_message. Therefore setting msg.spi = spi before calling spi_sync()
has no effect and can be removed.
(spi_message_add_tail() does not access this field.)
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240201201248.2334798-2-dlechner@baylibre.com
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Atmel WILC1000 SPI driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130104243.3025393-9-leitao@debian.org
Adding then removing a second vif currently makes the first vif not working
anymore. This is visible for example when we have a first interface
connected to some access point:
- create a wpa_supplicant.conf with some AP credentials
- wpa_supplicant -Dnl80211 -c /etc/wpa_supplicant.conf -i wlan0
- dhclient wlan0
- iw phy phy0 interface add wlan1 type managed
- iw dev wlan1 del
wlan0 does not manage properly traffic anymore (eg: ping not working)
This is due to vif mode being incorrectly reconfigured with some default
values in del_virtual_intf, affecting by default first vif.
Prevent first vif from being affected on second vif removal by removing vif
mode change command in del_virtual_intf
Fixes: 9bc061e88054 ("staging: wilc1000: added support to dynamically add/remove interfaces")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-5-54d29463a738@bootlin.com
Use the correct register configuration when the WILC chip is down so the
successive interface up operation is successful. The modified registers
values during chip down helps to avoid the "FW not responding" debug
message which sometimes occurs because of temporary bus communication
failure during the next start. Also, make sure on first communication with
the chip that it is indeed woken up.
Reported-by: Michael Walle <mwalle@kernel.org>
Closes: https://lore.kernel.org/linux-wireless/20221026085415.6jgwrhq4sunqaypm@0002.3ffe.de/
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-4-54d29463a738@bootlin.com
Commit 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to
"NETDEV-wq"") moved workqueue creation in wilc_netdev_ifc_init in order to
set the interface name in the workqueue name. However, while the driver
needs only one workqueue, the wilc_netdev_ifc_init is called each time we
add an interface over a phy, which in turns overwrite the workqueue with a
new one. This can be observed with the following commands:
for i in $(seq 0 10)
do
iw phy phy0 interface add wlan1 type managed
iw dev wlan1 del
done
ps -eo pid,comm|grep wlan
39 kworker/R-wlan0
98 kworker/R-wlan1
102 kworker/R-wlan1
105 kworker/R-wlan1
108 kworker/R-wlan1
111 kworker/R-wlan1
114 kworker/R-wlan1
117 kworker/R-wlan1
120 kworker/R-wlan1
123 kworker/R-wlan1
126 kworker/R-wlan1
129 kworker/R-wlan1
Fix this leakage by putting back hif_workqueue allocation in
wilc_cfg80211_init. Regarding the workqueue name, it is indeed relevant to
set it lowercase, however it is not attached to a specific netdev, so
enforcing netdev name in the name is not so relevant. Still, enrich the
name with the wiphy name to make it clear which phy is using the workqueue.
Fixes: 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-3-54d29463a738@bootlin.com
During firmware initial configuration in wilc_init_fw_config, the special
driver_handler 0 should be used instead of targeting a specific virtual
interface (either 1 or 2)
The issue does not seem to have real consequence (both virtual interfaces
seems to answer correctly to a Add Block Ack request with the Immediate
policy), but lets make everything homogeneous
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-2-54d29463a738@bootlin.com
With lockdep enabled, calls to the connect function from cfg802.11 layer
lead to the following warning:
=============================
WARNING: suspicious RCU usage
6.7.0-rc1-wt+ #333 Not tainted
-----------------------------
drivers/net/wireless/microchip/wilc1000/hif.c:386
suspicious rcu_dereference_check() usage!
[...]
stack backtrace:
CPU: 0 PID: 100 Comm: wpa_supplicant Not tainted 6.7.0-rc1-wt+ #333
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from wilc_parse_join_bss_param+0x7dc/0x7f4
wilc_parse_join_bss_param from connect+0x2c4/0x648
connect from cfg80211_connect+0x30c/0xb74
cfg80211_connect from nl80211_connect+0x860/0xa94
nl80211_connect from genl_rcv_msg+0x3fc/0x59c
genl_rcv_msg from netlink_rcv_skb+0xd0/0x1f8
netlink_rcv_skb from genl_rcv+0x2c/0x3c
genl_rcv from netlink_unicast+0x3b0/0x550
netlink_unicast from netlink_sendmsg+0x368/0x688
netlink_sendmsg from ____sys_sendmsg+0x190/0x430
____sys_sendmsg from ___sys_sendmsg+0x110/0x158
___sys_sendmsg from sys_sendmsg+0xe8/0x150
sys_sendmsg from ret_fast_syscall+0x0/0x1c
This warning is emitted because in the connect path, when trying to parse
target BSS parameters, we dereference a RCU pointer whithout being in RCU
critical section.
Fix RCU dereference usage by moving it to a RCU read critical section. To
avoid wrapping the whole wilc_parse_join_bss_param under the critical
section, just use the critical section to copy ies data
Fixes: c460495ee072 ("staging: wilc1000: fix incorrent type in initializer")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105075733.36331-3-alexis.lothore@bootlin.com
Reorder parameters declaration in wilc_parse_join_bss_param to enforce
reverse christmas tree
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240105075733.36331-2-alexis.lothore@bootlin.com
Simplify 'wilc_scan()' assuming 'struct wilc_priv *' is the only data
passed to '(*scan_result)()' callback and thus avoid typeless 'void *'
pointers in related code, including 'struct wilc_user_scan_req'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-2-dmantipov@yandex.ru
Remove set but otherwise unused 'ch' member of 'struct wilc_conn_info'
and avoid typeless 'void *' pointers in '(*conn_result)()' callback.
Likewise for 'wilc_parse_join_bss_param()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-1-dmantipov@yandex.ru
For 'struct wilc_remain_ch', drop set but otherwise unused 'duration'
field and adjust 'expired' callback assuming that the only data passed
to it is 'struct wilc_vif *', thus making 'wilc_remain_on_channel()'
a bit simpler as well. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026141016.71407-1-dmantipov@yandex.ru
Enabling KASAN and running some iperf tests raises some memory issues with
vmm_table:
BUG: KASAN: slab-out-of-bounds in wilc_wlan_handle_txq+0x6ac/0xdb4
Write of size 4 at addr c3a61540 by task wlan0-tx/95
KASAN detects that we are writing data beyond range allocated to vmm_table.
There is indeed a mismatch between the size passed to allocator in
wilc_wlan_init, and the range of possible indexes used later: allocation
size is missing a multiplication by sizeof(u32)
Fixes: 40b717bfcefa ("wifi: wilc1000: fix DMA on stack objects")
Cc: stable@vger.kernel.org
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231017-wilc1000_tx_oops-v3-1-b2155f1f7bee@bootlin.com
Using the full struct cfg80211_ap_settings for an update is
misleading, since most settings cannot be updated. Split the
update case off into a new struct cfg80211_ap_update.
Change-Id: I3ba4dd9280938ab41252f145227a7005edf327e4
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an algorithm to backoff the Tx Task when low memory scenario is
triggered at firmware. During high data transfer from host, the firmware
runs out of VMM memory, which is used to hold the frames from the host.
So, adding the flow control delays the transmit from host side when
there is not enough space to accommodate frames in firmware side.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230915175946.4361-1-prasurjya.rohansaikia@microchip.com
Modify the prototype for change_beacon() in struct cfg80211_op to
accept cfg80211_ap_settings instead of cfg80211_beacon_data so that
it can process data in addition to beacons.
Modify the prototypes of ieee80211_change_beacon() and driver specific
functions accordingly.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-4-quic_alokad@quicinc.com
[while at it, remove pointless "if (info)" check in tracing that just
makes all the lines longer than they need be - it's never NULL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 8399918f3056 ("staging: wilc1000: use RCU list to maintain vif interfaces list")
removed wilc_get_interface() but not its declaration.
Commit 9bc061e88054 ("staging: wilc1000: added support to dynamically add/remove interfaces")
declared but never implemented wilc_cfg_alloc() and wilc_netdev_interface().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230819102100.13720-1-yuehaibing@huawei.com
In some situations like, chip wake-up with powersave enabled, SPI
commands are failing temporarily. Reissuing commands after reset helps
to overcome the failure. So, add the retry limit and reset command
sequence API for read/write SPI commands.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724163955.4583-1-amisha.patel@microchip.com
The 'enhance throughput flow' algorithm is used by default. So older
sections of the code are removed so as to always use this new algorithm.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230710094401.235222-1-prasurjya.rohansaikia@microchip.com
In recent access points, information element is longer as they include
additional data which exceeds 256 bytes. To accommodate longer
association response, increase the ASSOC response buffer.
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230509172811.4953-1-amisha.patel@microchip.com
Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e595e ("wifi: wilc1000: validate pairwise and authentication suite offsets")
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com
Due to the two cherry picked commits from wireless to wireless-next we have
several conflicts in mt76. To avoid any bugs with conflicts merge wireless into
wireless-next.
96f134dc1964 wifi: mt76: handle possible mt76_rx_token_consume failures
fe13dad8992b wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fault injection test reports this issue:
kernel BUG at net/core/dev.c:10731!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
Call Trace:
<TASK>
wilc_netdev_ifc_init+0x19f/0x220 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_cfg80211_init+0x30c/0x380 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_bus_probe+0xad/0x2b0 [wilc1000_spi 1520a7539b6589cc6cde2ae826a523a33f8bacff]
spi_probe+0xe4/0x140
really_probe+0x17e/0x3f0
__driver_probe_device+0xe3/0x170
driver_probe_device+0x49/0x120
The root case here is alloc_ordered_workqueue() fails, but
cfg80211_unregister_netdevice() or unregister_netdev() not be called in
error handling path. To fix add unregister_netdev goto lable to add the
unregister operation in error handling path.
Fixes: 09ed8bfc5215 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1669289902-23639-1-git-send-email-wangyufen@huawei.com
There is no validation of 'e->no_of_channels' which can trigger an
out-of-bounds write in the following 'memset' call. Validate that the
number of channels does not extends beyond the size of the channel list
element.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-5-philipturnbull@github.com
Validate that the IEEE80211_P2P_ATTR_CHANNEL_LIST attribute contains
enough space for a 'struct wilc_attr_oper_ch'. If the attribute is too
small then it can trigger an out-of-bounds write later in the function.
'struct wilc_attr_oper_ch' is variable sized so also check 'attr_len'
does not extend beyond the end of 'buf'.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-4-philipturnbull@github.com
Validate that the IEEE80211_P2P_ATTR_OPER_CHANNEL attribute contains
enough space for a 'struct struct wilc_attr_oper_ch'. If the attribute is
too small then it triggers an out-of-bounds write later in the function.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-3-philipturnbull@github.com
There is no validation of 'offset' which can trigger an out-of-bounds
read when extracting RSN capabilities.
Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-2-philipturnbull@github.com
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d52 ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Return value from cfg80211_rx_mgmt() directly instead of
taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220830105505.287564-1-cui.jinpeng2@zte.com.cn
Sometimes 'wilc_sdio_cmd53' is called with addresses pointing to an
object on the stack. Use dynamically allocated memory for cmd53 instead
of stack address which is not DMA'able.
Fixes: 5625f965d764 ("wilc1000: move wilc driver out of staging")
Reported-by: Michael Walle <mwalle@kernel.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Tested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809075749.62752-1-ajay.kathat@microchip.com
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
-----BEGIN PGP SIGNATURE-----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=J5Fc
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sparse warns:
drivers/net/wireless/microchip/wilc1000/hif.h:218:35: error: marked inline, but without a definition
Remove the inline, it's not needed.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220801110440.13144-1-kvalo@kernel.org
