IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
A problem about ntb_hw_idt create debugfs failed is triggered with the
following log given:
[ 1236.637636] IDT PCI-E Non-Transparent Bridge Driver 2.0
[ 1236.639292] debugfs: Directory 'ntb_hw_idt' with parent '/' already present!
The reason is that idt_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_idt can never be created later.
idt_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: bf2a952d31 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When building with Clang we encounter these warnings:
| drivers/ntb/hw/idt/ntb_hw_idt.c:2409:28: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
| "\t%hhu-%hhu.\t", idx + cnt - 1);
-
| drivers/ntb/hw/idt/ntb_hw_idt.c:2438:29: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat]
| "\t%hhu-%hhu.\t", idx + cnt - 1);
-
| drivers/ntb/hw/idt/ntb_hw_idt.c:2484:15: error: format specifies type
| 'unsigned char' but the argument has type 'int' [-Werror,-Wformat], src);
For the first two warnings the format specifier used is `%hhu` which
describes a u8. Both `idx` and `cnt` are u8 as well. However, the
expression as a whole is promoted to an int as you cannot get
smaller-than-int from addition. Therefore, to fix the warning, use the
promoted-to-type's format specifier -- in this case `%d`.
example:
``
uint8_t a = 4, b = 7;
int size = sizeof(a + b - 1);
printf("%d\n", size);
// output: 4
```
For the last warning, src is of type `int` while the format specifier
describes a u8. The fix here is just to use the proper specifier `%d`.
See more:
(https://wiki.sei.cmu.edu/confluence/display/c/INT02-C.+Understand+integer+conversion+rules)
"Integer types smaller than int are promoted when an operation is
performed on them. If all values of the original type can be represented
as an int, the value of the smaller type is converted to an int;
otherwise, it is converted to an unsigned int."
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <justinstitt@google.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
idt_create_dev never return NULL and fix smatch warning.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This patch removes the code that sets the DMA mask as it no longer
makes sense to do this.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since IDT PCIe-switch temperature sensor is now always available
irregardless of the EEPROM/BIOS settings, Kconfig and in-code
description should be properly altered. In addition lets update
the driver copyright lines.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT PCIe-switch temperature sensor interface is very broken. First
of all only a few combinations of TMPCTL threshold enable bits
really cause the interrupts unmasked. Even if an individual bit
indicates the event unmasked, corresponding IRQ just isn't generated.
Most of the threshold enable bits combinations are in fact useless and
non of them can help to create a fully functional alarm interface.
So to speak, we can't create a well defined hwmon alarms based on
the IDT PCI-switch threshold IRQs.
Secondly a single threshold IRQ (not a combination of thresholds) can
be successfully enabled without the issue described above. But in this
case we experienced an enormous number of interrupts generated by
the chip if the temperature got near the enabled threshold value. Filter
adjustment didn't help much. It also doesn't provide a hysteresis settings.
Due to the temperature sample fluctuations near the threshold the
interrupts spate makes the system nearly unusable until the temperature
value finally settled so being pushed either to be fully higher or lower
the threshold.
All of these issues makes the temperature sensor alarm interface useless
and even at some point dangerous to be used in the driver. In this case
it is safer to completely discard it and disable the temperature alarm
interrupts.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT PCIe switches provide an embedded temperature sensor working
within [0; 127.5]C with resolution of 0.5C. They also can generate
a PCIe upstream interrupt in case if the temperature passes through
specified thresholds. Since this thresholds interface is very broken
the created hwmon-sysfs interface exposes only the next set of hwmon
nodes: current input temperature, lowest and highest values measured,
history resetting, value offset. HWmon alarm interface isn't provided.
IDT PCIe switch also've got an ADC/filter settings of the sensor.
This driver doesn't expose them to the hwmon-sysfs interface at the
moment, except the offset node.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order to create a hwmon interface for the IDT PCIe-switch temperature
sensor the already available reader method should be improved. Particularly
we need to redesign it so one would be able to read temperature/offset
values from registers of the passed types. Since IDT sensor interface
provides temperature in unsigned format 0:7:1 (7 bits for real value
and one for fraction) we also need to have helpers for the typical sysfs
temperature data type conversion to and from this format. Even though
the IDT PCIe-switch provided temperature offset got the same but signed
type it can be translated by these methods too.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT NTB driver sets the upper limit of actual translation address
being written to the corresponding memory window setup. It is achieved
by BARLIMITx register initialization. Needless to say, that the register
works within PCIe bus address space.
In general CPU and PCIe address spaces are different. It means,
that addresses used for Memory TLPs routine can be different from
CPU addresses. While in most of cases they are the same, there are
exceptions when the proper mapping must be performed to have the
portable driver code. There used to be a virt_to_bus()/bus_to_virt()
interface for this purpose. But it's deprecated now. It was also a
mistake to use pci_resource_start() since the return address of the
method is at the CPU address space. In order to achieve the desired
purpose we need to use pci_bus_address() helper. This method shall
return a PCIe bus base address of the corresponding BAR resource.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Both devm_kcalloc() and devm_kzalloc() return NULL on error. They
never return error pointers.
The use of IS_ERR_OR_NULL is currently applied to the wrong
context.
Fix this by replacing IS_ERR_OR_NULL with regular NULL checks.
Fixes: bf2a952d31 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Since Switchtec patch there has been a new topology added to
the NTB API. It's called NTB_TOPO_SWITCH and dedicated for
PCIe switch chips. Even though topo field isn't used within the
IDT driver much, lets set it for the sake of unification.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The dma_mask and dma_coherent_mask fields of the NTB struct device
weren't initialized in hardware drivers. In fact it should be done
instead of PCIe interface usage, since NTB clients are supposed to
use NTB API and left unaware of real hardware implementation.
In addition to that ntb_device_register() method shouldn't clear
the passed ntb_dev structure, since it dma_mask is initialized
by hardware drivers.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is a common methods signature form used over all the NTB API
like functions naming scheme, arguments names and order, etc.
Recently added NTB messaging API IO callbacks were named a bit
different so should be renamed to be in compliance with the rest
of the API.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT 89HPESxNTx device series is PCIe-switches, which support
Non-Transparent bridging between domains connected to the device ports.
Since new NTB API exposes multi-port interface and messaging API, the
IDT NT-functions can be now supported in the kernel. This driver adds
the following functionality:
1) Multi-port NTB API to have information of possible NT-functions
activated in compliance with available device ports.
2) Memory windows of direct and look up table based address translation
with all possible combinations of BARs setup.
3) Traditional doorbell NTB API.
4) One-on-one messaging NTB API.
There are some IDT PCIe-switch setups, which must be done before any of
the NTB peers started. It can be performed either by system BIOS via
IDT SMBus-slave interface or by pre-initialized IDT PCIe-switch EEPROM:
1) NT-functions of corresponding ports must be activated using
SWPARTxCTL and SWPORTxCTL registers.
2) BAR0 must be configured to expose NT-function configuration
registers map.
3) The rest of the BARs must have at least one memory window
configured, otherwise the driver will just return an error.
Temperature sensor of IDT PCIe-switches can be also optionally
activated by BIOS or EEPROM.
(See IDT documentations for details of how the pre-initialization can
be done)
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
