IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace scnprintf with sysfs_emit_at which is the preferred alternative.
Also make sure each fractional digit is in its place by padding with
zeros up to 3 digits: "...%03d...".
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230620163135.93780-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check IIO_PROXIMITY with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DA217 accelerometer is another DA280 compatible accelerometer,
add its device-ids to the da280 driver.
Reported-by: Juno Computers USA <usa@junocomputers.com>
Tested-by: Juno Computers USA <usa@junocomputers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230613094346.162551-1-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace timestamping by the new common inv_sensors timestamp
module. The principle behind is the same but the implementation in
the new module is far better providing less jitter and a better
estimation.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create new inv_sensors common modules and move inv_icm42600
timestamp module inside. This module will be used by IMUs and
also in the future by other chips.
Modify inv_icm42600 driver to use timestamp module and do some
headers cleanup.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move icm42600 dependent function inside the core module.
Do some headers cleanup at the same time.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
power-sensor@40 {
compatible = "ti,ina232", "ti,ina231";
...
};
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Link: https://lore.kernel.org/r/20230619141239.2257392-1-alvin@pqrs.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The intensity data from bu27008 is unsigned. The type of the scan data
was incorrectly marked as signed resulting large intensity values to be
interpreted as negative ones.
Fix the scan data type.
Fixes: 41ff93d14f78 ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/240a7ca5fc1b76da20d81f930d00f31a54b1fdf8.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver is expecting accuracy of NANOs for intensity scale in
raw_write. The IIO core is however defaulting to MICROs. This leads the
raw-write of smallest scales to never succeed as correct selector(s) are
not found.
Fix this by implementing the .write_raw_get_fmt callback to use NANO
accuracy for writes of IIO_CHAN_INFO_SCALE.
Fixes: 41ff93d14f78 ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e4778b74cde41431f77bc8dd88ec18605da0b400.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver is expecting accuracy of NANOs for intensity scale in
raw_write. The IIO core is however defaulting to MICROs. This leads the
raw-write of smallest scales to never succeed as correct selector(s) are
not found.
Fix this by implementing the .write_raw_get_fmt callback to use NANO
accuracy for writes of IIO_CHAN_INFO_SCALE.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e52afbd61039 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Link: https://lore.kernel.org/r/5369117315cf05b88cf0ccb87373fd77190f6ca2.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AC excitation enable feature exposed to user on AD7192, allowing a bit
which should be 0 to be set. This feature is specific only to AD7195. AC
excitation attribute moved accordingly.
In the AD7195 documentation, the AC excitation enable bit is on position
22 in the Configuration register. ACX macro changed to match correct
register and bit.
Note that the fix tag is for the commit that moved the driver out of
staging.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230614155242.160296-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Print read and expected device ID as debug warning.
Add error check for ad_sd_init() result.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Markus Burri <markus.burri@mt.com>
Link: https://lore.kernel.org/r/20230614073033.2497318-1-markus.burri@mt.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If st->mclk is not NULL, then st->clock_sel is either AD7192_CLK_EXT_MCLK2
or AD7192_CLK_EXT_MCLK1_2.
So devm_clk_get_optional_enabled() can be used instead of hand writing it.
This saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/7dbe973905f1fdae5d2f5ae5a3b01dd1d6a9925b.1686774340.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A helper, iio_read_max_channel_raw() exists to read the available
maximum raw value of a channel but nothing similar exists to read the
available minimum raw value.
This new helper, iio_read_min_channel_raw(), fills the hole and can be
used for reading the available minimum raw value of a channel.
It is fully based on the existing iio_read_max_channel_raw().
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-11-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This FIXME comment is more a TODO one.
It is a note when someone will need for this currently unsupported case.
Change from FIXME to TODO.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-10-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use max_array() to get the maximum value from an array instead of a
custom local loop.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-9-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the mutex.h inclusion order as it seems to be the only one
misplaces.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-7-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code uses a local variable to initialize a null pointer in order to
avoid accessing this null pointer later on.
Simply removed the 'unused' variable and check for the null pointer just
before accessing it.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-6-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation returns the error code as part of the
default switch case.
This can lead to returning an incorrect positive value in case of
iio_avail_type enum entries evolution.
In order to avoid this case, be more strict in error checking.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20230623085830.749991-4-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKSEQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoowCfT+Joha+cz4edAFUvd55lKPPJJFsAoNiprHmX
di37sirvn6vo54Hk0Nyq
=qqTo
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are a small set of changes for 6.5-rc1 for some driver core
changes. Included in here are:
- device property cleanups to make it easier to write "agnostic"
drivers when regards to the firmware layer underneath them (DT vs.
ACPI)
- debugfs documentation updates
- devres additions
- sysfs documentation and changes to handle empty directory creation
logic better
- tiny kernfs optimizations
- other tiny changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Skip empty folders creation
sysfs: Improve readability by following the kernel coding style
drivers: fwnode: fix fwnode_irq_get[_byname]()
ata: ahci_platform: Make code agnostic to OF/ACPI
device property: Implement device_is_compatible()
ACPI: Move ACPI_DEVICE_CLASS() to mod_devicetable.h
base/node: Use 'property' to identify an access parameter
driver core: device.h: add some missing kerneldocs
kernfs: fix missing kernfs_idr_lock to remove an ID from the IDR
isa: Remove unnecessary checks
MAINTAINERS: add entry for auxiliary bus
debugfs: Correct the 'debugfs_create_str' docs
serial: qcom_geni: Comment use of devm_krealloc rather than devm_krealloc_array
iio: adc: Use devm_krealloc_array
hwmon: pmbus: Use devm_krealloc_array
Here is the big set of char/misc and other driver subsystem updates for
6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates
on top of that, lots of small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKNMw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylhlQCfZrtz8RIbau8zbzh/CKpKBOmvHp4An3V64hbz
recBPLH0ZACKl0wPl4iZ
=A83A
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.5-rc1.
Lots of different, tiny, stuff in here, from a range of smaller driver
subsystems, including pulls from some substems directly:
- IIO driver updates and additions
- W1 driver updates and fixes (and a new maintainer!)
- FPGA driver updates and fixes
- Counter driver updates
- Extcon driver updates
- Interconnect driver updates
- Coresight driver updates
- mfd tree tag merge needed for other updates on top of that, lots of
small driver updates as patches, including:
- static const updates for class structures
- nvmem driver updates
- pcmcia driver fix
- lots of other small driver updates and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (243 commits)
bsr: fix build problem with bsr_class static cleanup
comedi: make all 'class' structures const
char: xillybus: make xillybus_class a static const structure
xilinx_hwicap: make icap_class a static const structure
virtio_console: make port class a static const structure
ppdev: make ppdev_class a static const structure
char: misc: make misc_class a static const structure
/dev/mem: make mem_class a static const structure
char: lp: make lp_class a static const structure
dsp56k: make dsp56k_class a static const structure
bsr: make bsr_class a static const structure
oradax: make 'cl' a static const structure
hwtracing: hisi_ptt: Fix potential sleep in atomic context
hwtracing: hisi_ptt: Advertise PERF_PMU_CAP_NO_EXCLUDE for PTT PMU
hwtracing: hisi_ptt: Export available filters through sysfs
hwtracing: hisi_ptt: Add support for dynamically updating the filter list
hwtracing: hisi_ptt: Factor out filter allocation and release operation
samples: pfsm: add CC_CAN_LINK dependency
misc: fastrpc: check return value of devm_kasprintf()
coresight: dummy: Update type of mode parameter in dummy_{sink,source}_enable()
...
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
- New Device Support
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
- Removed Device Support
- Removed MFD support for Richtek RT5033 Battery
- Fix-ups
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
- Bug Fixes
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading
-----BEGIN PGP SIGNATURE-----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=EmOj
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for TI TPS6594/TPS6593/LP8764 PMICs
- Add support for Samsung RT5033 Battery Charger
- Add support for Analog Devices MAX77540 and MAX77541 PMICs
New Device Support:
- Add support for SPI to Rockchip RK808 (and friends)
- Add support for AXP192 PMIC to X-Powers AXP20X
- Add support for AXP313a PMIC to X-Powers AXP20X
- Add support for RK806 to Rockchip RK8XX
Removed Device Support:
- Removed MFD support for Richtek RT5033 Battery
Fix-ups:
- Remove superfluous code
- Switch I2C drivers from .probe_new() to .probe()
- Convert over to managed resources (devm_*(), etc)
- Use dev_err_probe() for returning errors from .probe()
- Add lots of Device Tree bindings / support
- Improve cache efficiency by switching to Maple
- Use own exported namespaces (NS)
- Include missing and remove superfluous headers
- Start using / convert to the new shutdown sys-off API
- Trivial: variable / define renaming
- Make use of of_property_read_reg() when requesting DT 'reg's
Bug Fixes:
- Fix chip revision readout due to incorrect data masking
- Amend incorrect register and mask values used for charger state
- Hide unused functionality at compile time
- Fix resource leaks following error handling routines
- Return correct error values and fix error handling in general
- Repair incorrect device names - used for device matching
- Remedy broken module auto-loading"
* tag 'mfd-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (51 commits)
dt-bindings: mfd: max77541: Add ADI MAX77541/MAX77540
iio: adc: max77541: Add ADI MAX77541 ADC Support
regulator: max77541: Add ADI MAX77541/MAX77540 Regulator Support
dt-bindings: regulator: max77541: Add ADI MAX77541/MAX77540 Regulator
mfd: Switch two more drivers back to use struct i2c_driver::probe
dt-bindings: mfd: samsung,s5m8767: Simplify excluding properties
mfd: stmpe: Only disable the regulators if they are enabled
mfd: max77541: Add ADI MAX77541/MAX77540 PMIC Support
dt-bindings: mfd: gateworks-gsc: Remove unnecessary fan-controller nodes
mfd: core: Use of_property_read_reg() to parse "reg"
mfd: stmfx: Nullify stmfx->vdd in case of error
mfd: stmfx: Fix error path in stmfx_chip_init
mfd: intel-lpss: Add missing check for platform_get_resource
mfd: stpmic1: Add PMIC poweroff via sys-off handler
mfd: stpmic1: Fixup main control register and bits naming
dt-bindings: mfd: qcom,tcsr: Add the compatible for IPQ8074
mfd: tps65219: Add support for soft shutdown via sys-off API
mfd: pm8008: Drop bogus i2c module alias
mfd: pm8008: Fix module autoloading
mfd: tps65219: Add GPIO cell instance
...
The MAX77541 has an 8-bit Successive Approximation Register (SAR) ADC
with four multiplexers for supporting the telemetry feature.
Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230412111256.40013-4-okan.sahin@analog.com
Signed-off-by: Lee Jones <lee@kernel.org>
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
-----BEGIN PGP SIGNATURE-----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=0gJ9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
According to the datasheets of supported meson SoCs length of ADC_CLK_DIV
field is 6-bit. Although all supported SoCs have the register
with that field documented later SoCs use external clock rather than
ADC internal clock so this patch affects only meson8 family (S8* SoCs).
Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230606165357.42417-1-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Scan elements for x,y,z channels is little endian and requires no bit shifts.
LE vs. BE is controlled in register SENS_CONFIG2 and bit LE_BE, default
value is LE.
Fixes: a3e0b51884ee ("iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230605103223.1400980-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix wrong selection of internal clock when mclk is defined.
Resolve a logical inversion introduced in c9ec2cb328e3.
Fixes: c9ec2cb328e3 ("iio: adc: ad7192: use devm_clk_get_optional() for mclk")
Signed-off-by: Fabrizio Lamarque <fl.scratchpad@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230530075311.400686-3-fl.scratchpad@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pointer to indio_dev structure is obtained via spi_get_drvdata() at
the beginning of function ad7192_setup(), but the spi->dev->driver_data
member is not initialized, hence a NULL pointer is returned.
Fix by changing ad7192_setup() signature to take pointer to struct
iio_dev, and get ad7192_state pointer via st = iio_priv(indio_dev);
Fixes: bd5dcdeb3fd0 ("iio: adc: ad7192: convert to device-managed functions")
Signed-off-by: Fabrizio Lamarque <fl.scratchpad@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230530075311.400686-2-fl.scratchpad@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Apparently, despite the name Digital Input Configuration Register, the
settings in the DIN_CONFIGx registers also affect other channel
functions. In particular, setting a non-zero value in the DIN_SINK
field breaks the resistance measurement function.
Now, one can of course argue that specifying a drive-strength-microamp
property along with a adi,ch-func which is not one of the digital
input functions is a bug in the device tree. However, we have a rather
complicated setup with instances of ad74412r on external hardware
modules, and have set a default drive-strength-microamp in our DT
fragments describing those, merely modifying the adi,ch-func settings
to reflect however the modules have been wired up. And restricting
this setting to just being done for digital input doesn't make the
driver any more complex.
Fixes: 504eb485589d1 (iio: ad74413r: wire up support for drive-strength-microamp property)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230503105042.453755-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use dev_err_probe instead of dev_err in probe function,
which simplifies code a little bit and prints the error
code.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-7-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Match alignment with open parenthesis for improving the code
readability.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230603185340.13838-6-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-5-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_clk_get_enabled() to avoid manually disabling the
clock.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-4-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new start and read functions to support rk3588 device.
Also, add a device compatible string for the same.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230603185340.13838-3-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add start, read and power_down callback functions,
which will help in adding new rockchip device support
cleanly.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-2-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that it exists, use it instead of doing the multiplication and
checking for overflow manually.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: James Clark <james.clark@arm.com>
Link: https://lore.kernel.org/r/20230509094942.396150-4-james.clark@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds an of_device_id table entry to the driver, enabling
device matching through device tree. With this update, the driver
can now match devices using both the i2c_device_id entry and the
newly added of_device_id table.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/72746bdfd8f74171943e41759b891c7af40627ec.1684579603.git.anupnewsmail@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
