IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
There is QE on platform T104x, add support.
Call funcs qe_ic_init and qe_init if CONFIG_QUICC_ENGINE is defined.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
[scottwood@freesacle.com: whitespace fix]
Signed-off-by: Scott Wood <scottwood@freescale.com>
New QE doesn't have par_io, it doesn't need to init par_io
for new QE.
Split function mpc85xx_qe_init() into mpc85xx_qe_init()
and mpc85xx_qe_par_io_init().
Call mpc85xx_qe_init() for both new and old while
mpc85xx_qe_par_io_init() after mpc85xx_qe_init() for old.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
If CONFIG_UCC_GETH or CONFIG_SERIAL_QE is not defined then we get a
warning about an used variable which leads to a build error.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
CONFIG_FSL_IFC gets enabled by Kconfig dependancies.
So remove unnecssary define from the defconfigs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add power sensor chip ina220 node in dts to support
power monitor
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The MPC7448HPC2 and PPC_HOLLY config options contain TSI108_BRIDGE
duplicates since commit:
commit 3490cba56f7f8a78ef4c94814c3181f09ce1e2ef
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jan 23 12:42:50 2008 -0600
[POWERPC] Add initial iomega StorCenter board port.
This patch cleans these duplicates.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For PEXCSRBAR, bit 3-0 indicate prefetchable and address type.
So when getting base address, these bits should be masked,
otherwise we may get incorrect base address.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The following SoCs will be affected: p2041, p3041, p4080,
p5020, p5040, b4420, b4860, t4240
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJTItl6AAoJEBvWZb6bTYby/EMP/A+/l9rU9oji5nns2ei2YVf7
kmnpshb2rgDP6gTtPet3qPKcSUNq4bG7zPEZ04FG5H70PduDYBWchfT/jTZKxcBB
rZgtrsMAzGjoxvtsQAc1yQiMtlkG28HD3yn0TC7BvazTQlZnzHVZTmiCZc9r0Qo7
SjLslo00ITbhRVwkLi1cuSeuaNcim1WDgxeUFhpRd48HoywtkzGLGuU8dWmakwb0
IDoo6X9srNlmZgrRdMaBS3agQtt1GoOE2T/KaJbnJ6lmnkGzBVKrw8kIZamQlwnK
GnmJAM//1zu4eoWJquNuc9wqsZK2t0e68LXAL9HLeMQGyl1YBh5hTiInTUnXiCAI
D/r/rkF2lqPgKotDBY/Q1l0bHABR53MOwa5ooZANLatnTwTv4gSpM8L1CAnekGhq
dxqVYqeJr1+ZemhalO1pbi/V9CfpJHBBye9JDan8rJmkj25kCH7PF3BxLYgKckQs
OtfZyOqpsZSCvpzFQa70VmWTGDqOxk686/R9ql88sdGbgyzZOHxHCeMIoAgCah6c
o5s1CktKKLOmC2M6NNn1z44V1/LmmC2fgKuaSjI/y7rjgGwRoGrAV1giVMdnTc5y
hGo4fD83/zHJnkafVdBQbmkKP69bC65a0w4iLXSxOKkPtHCI3c2IrZpovAC42aTp
iREImat0+YzW4hDRI+qa
=uZp5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull another kvm fix from Paolo Bonzini:
"A fix for a PowerPC bug that was introduced during the 3.14 merge
window"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix register usage when loading/saving VRSAVE
KVM: PPC: Book3S HV: Remove bogus duplicate code
Enable reserved memory initialization from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Commit 595e4f7e697e ("KVM: PPC: Book3S HV: Use load/store_fp_state
functions in HV guest entry/exit") changed the register usage in
kvmppc_save_fp() and kvmppc_load_fp() but omitted changing the
instructions that load and save VRSAVE. The result is that the
VRSAVE value was loaded from a constant address, and saved to a
location past the end of the vcpu struct, causing host kernel
memory corruption and various kinds of host kernel crashes.
This fixes the problem by using register r31, which contains the
vcpu pointer, instead of r3 and r4.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 7b490411c37f ("KVM: PPC: Book3S HV: Add new state for
transactional memory") incorrectly added some duplicate code to the
guest exit path because I didn't manage to clean up after a rebase
correctly. This removes the extraneous material. The presence of
this extraneous code causes host crashes whenever a guest is run.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Device tree nodes are already treated as objects, and we already want to
expose them to userspace which is done using the /proc filesystem today.
Right now the kernel has to do a lot of work to keep the /proc view in
sync with the in-kernel representation. If device_nodes are switched to
be kobjects then the device tree code can be a whole lot simpler. It
also turns out that switching to using /sysfs from /proc results in
smaller code and data size, and the userspace ABI won't change if
/proc/device-tree symlinks to /sys/firmware/devicetree/base.
v7: Add missing sysfs_bin_attr_init()
v6: Add __of_add_property() early init fixes from Pantelis
v5: Rename firmware/ofw to firmware/devicetree
Fix updating property values in sysfs
v4: Fixed build error on Powerpc
Fixed handling of dynamic nodes on powerpc
v3: Fixed handling of duplicate attribute and child node names
v2: switch to using sysfs bin_attributes which solve the problem of
reporting incorrect property size.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Remove mc_capable() and smt_capable(). Neither is used.
Both were added by 5c45bf279d37 ("sched: mc/smt power savings sched
policy"). Uses of both were removed by 8e7fbcbc22c1 ("sched: Remove stale
power aware scheduling remnants and dysfunctional knobs").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20140304210737.16893.54289.stgit@bhelgaas-glaptop.roam.corp.google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GFP_THISNODE is for callers that implement their own clever fallback to
remote nodes. It restricts the allocation to the specified node and
does not invoke reclaim, assuming that the caller will take care of it
when the fallback fails, e.g. through a subsequent allocation request
without GFP_THISNODE set.
However, many current GFP_THISNODE users only want the node exclusive
aspect of the flag, without actually implementing their own fallback or
triggering reclaim if necessary. This results in things like page
migration failing prematurely even when there is easily reclaimable
memory available, unless kswapd happens to be running already or a
concurrent allocation attempt triggers the necessary reclaim.
Convert all callsites that don't implement their own fallback strategy
to __GFP_THISNODE. This restricts the allocation a single node too, but
at the same time allows the allocator to enter the slowpath, wake
kswapd, and invoke direct reclaim if necessary, to make the allocation
happen when memory is full.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Jan Stancek <jstancek@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the data parameter is not really used by any ftrace_dyn_arch_init,
remove that from ftrace_dyn_arch_init. This also removes the addr
local variable from ftrace_init which is now unused.
Note the documentation was imprecise as it did not suggest to set
(*data) to 0.
Link: http://lkml.kernel.org/r/1393268401-24379-4-git-send-email-jslaby@suse.cz
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
No architecture uses the "data" parameter in ftrace_dyn_arch_init() in any
way, it just sets the value to 0. And this is used as a return value
in the caller -- ftrace_init, which just checks the retval against
zero.
Note there is also "return 0" in every ftrace_dyn_arch_init. So it is
enough to check the retval and remove all the indirect sets of data on
all archs.
Link: http://lkml.kernel.org/r/1393268401-24379-3-git-send-email-jslaby@suse.cz
Cc: linux-arch@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.
Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Flow:
- We register for OPAL notification events.
- OPAL sends new dump available notification.
- We make information on dump available via sysfs
- Userspace requests dump contents
- We retrieve the dump via OPAL interface
- User copies the dump data
- userspace sends ack for dump
- We send ACK to OPAL.
sysfs files:
- We add the /sys/firmware/opal/dump directory
- echoing 1 (well, anything, but in future we may support
different dump types) to /sys/firmware/opal/dump/initiate_dump
will initiate a dump.
- Each dump that we've been notified of gets a directory
in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
as this is what's used elsewhere to identify the dump).
- Each dump has files: id, type, dump and acknowledge
dump is binary and is the dump itself.
echoing 'ack' to acknowledge (currently any string will do) will
acknowledge the dump and it will soon after disappear from sysfs.
OPAL APIs:
- opal_dump_init()
- opal_dump_info()
- opal_dump_read()
- opal_dump_ack()
- opal_dump_resend_notification()
Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.
We export each log entry as a directory in /sys/firmware/opal/elog/
Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.
Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).
If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.
A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.
On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.
I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The previous code added wrong TLBs and causes machine check errors if
a driver accessed passed the end of the linear mapping instead of
a clean page fault.
Signed-off-by: Ralph E. Bellofatto <ralphbel@us.ibm.com>
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc uses early_init_dt_scan_chosen() from common fdt code. By
enabling this option, the common code can take the built in
command line over the one that is comming from bootloader / DT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Traditionally it has been drmgr's responsibilty to update the device tree
through the /proc/ppc64/ofdt interface after a suspend/resume operation.
This patchset however has modified suspend/resume ops to preform an update
entirely in the kernel during the resume. Therefore, a mechanism is required
to expose that information to drmgr.
This patch adds a show function to the "hibernate" attribute that returns 1
if the kernel performs a device tree update after the resume and 0 otherwise.
This allows newer versions of drmgr to avoid doing a second unnecessary
device tree update.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pHyp can change cache nodes for suspend/resume operation. Currently the
device tree is updated by drmgr in userspace after all non boot CPUs are
enabled. Hence, we do not modify the cache list based on the latest cache
nodes. Also we do not remove cache entries for the primary CPU.
This patch removes the cache list for the boot CPU, updates the device tree
before enabling nonboot CPUs and adds cache list for the boot cpu.
This patch also has the side effect that older versions of drmgr will
perform a second device tree update from userspace. While this is a
redundant waste of a couple cycles it is harmless since firmware returns the
same data for the subsequent update-nodes/properties rtas calls.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code makes rtas calls for update-nodes, activate-firmware and then
update-nodes again. The FW provides the same data for both update-nodes calls.
As a result a proc entry exists error is reported for the second update while
adding device nodes.
This patch makes a single rtas call for update-nodes after activating the FW.
It also add rtas_busy delay for the activate-firmware rtas call.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This processor/memory module was mostly used on ATCA blades and
before that, on cPCI blades. It wasn't really user friendly, with
custom non u-boot bootloaders (powerboot/motload) and no real way
to recover corrupted boot flash (which was a common problem).
As such, it had its day back before the big ppc --> powerpc move
to device trees, and that was largely through commercial BSPs that
started to dry up around 2007.
Systems using one were largely in a "deploy and sustain" mode,
so interest in upgrading to new kernels in the field was nil.
Also, requiring 50A, 48V power supplies and a 2'x2'x2' ATCA
chassis largely rules out any hobbyist/enthusiast interest.
The point of all this, is that we might as well delete the in
kernel files relating to this platform. No point in continuing
to build it via walking the defconfigs or via linux-next testing.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The memory remove code for powerpc/pseries should call remove_memory()
so that we are holding the hotplug_memory lock during memory remove
operations.
This patch updates the memory node remove handler to call remove_memory()
and adds a ppc_md.remove_memory() entry to handle pseries specific work
that is called from arch_remove_memory().
During memory remove in pseries_remove_memblock() we have to stay with
removing memory one section at a time. This is needed because of how memory
resources are handled. During memory add for pseries (via the probe file in
sysfs) we add memory one section at a time which gives us a memory resource
for each section. Future patches will aim to address this so will not have
to remove memory one section at a time.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Turn Anton's memcpy / copy_tofrom_user test into something that can
live in tools/testing/selftests.
It requires one turd in arch/powerpc/lib/memcpy_64.S, but it's pretty
harmless IMHO.
We are sailing very close to the wind with the feature macros. We define
them to nothing, which currently means we get a few extra nops and
include the unaligned calls.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This results in oddball messages at boot on other platforms telling us
that CPU hotplug isn't supported even when it is.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes the disassembler of the powerpc kernel debugger xmon,
for little-endian.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch reverts my previous "fix", and replace it with the correct
fix from Russell.
And as Russell pointed out -- dma_set_mask_and_coherent() (and the other
dma_set_mask() functions) are really supposed to be used by drivers
only.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes CONFIG_MTD_PARTITIONS in config files for powerpc.
Because CONFIG_MTD_PARTITIONS was removed by commit 6a8a98b22b10f1560d5f90aded4a54234b9b2724.
Signed-off-by: Eunbong Song <eunb.song@samsung.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 64bit relocation code places a few symbols in the text segment.
These symbols are only 4 byte aligned where they need to be 8 byte
aligned. Add an explicit alignment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we fork/clone we currently don't copy any of the TM state to the new
thread. This results in a TM bad thing (program check) when the new process is
switched in as the kernel does a tmrechkpt with TEXASR FS not set. Also, since
R1 is from userspace, we trigger the bad kernel stack pointer detection. So we
end up with something like this:
Bad kernel stack pointer 0 at c0000000000404fc
cpu 0x2: Vector: 700 (Program Check) at [c00000003ffefd40]
pc: c0000000000404fc: restore_gprs+0xc0/0x148
lr: 0000000000000000
sp: 0
msr: 9000000100201030
current = 0xc000001dd1417c30
paca = 0xc00000000fe00800 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/2
WARNING: exception is not recoverable, can't continue
The below fixes this by flushing the TM state before we copy the task_struct to
the clone. To do this we go through the tmreclaim patch, which removes the
checkpointed registers from the CPU and transitions the CPU out of TM suspend
mode. Hence we need to call tmrechkpt after to restore the checkpointed state
and the TM mode for the current task.
To make this fail from userspace is simply:
tbegin
li r0, 2
sc
<boom>
Kudos to Adhemerval Zanella Neto for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Adhemerval Zanella Neto <azanella@br.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fast sleep is one of the deep idle states on Power8 in which local timers of
CPUs stop. On PowerPC we do not have an external clock device which can
handle wakeup of such CPUs. Now that we have the support in the tick broadcast
framework for archs that do not sport such a device and the low level support
for fast sleep, enable it in the cpuidle framework on PowerNV.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During "Fast-sleep" and deeper power savings state, decrementer and
timebase could be stopped making it out of sync with rest
of the cores in the system.
Add a firmware call to request platform to resync timebase
using low level platform methods.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before adding Fast-Sleep into the cpuidle framework, some low level
support needs to be added to enable it. This includes saving and
restoring of certain registers at entry and exit time of this state
respectively just like we do in the NAP idle state.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[Changelog modified by Preeti U. Murthy <preeti@linux.vnet.ibm.com>]
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Split timer_interrupt(), which is the local timer interrupt handler on ppc
into routines called during regular interrupt handling and __timer_interrupt(),
which takes care of running local timers and collecting time related stats.
This will enable callers interested only in running expired local timers to
directly call into __timer_interupt(). One of the use cases of this is the
tick broadcast IPI handling in which the sleeping CPUs need to handle the local
timers that have expired.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For scalability and performance reasons, we want the tick broadcast IPIs
to be handled as efficiently as possible. Fixed IPI messages
are one of the most efficient mechanisms available - they are faster than
the smp_call_function mechanism because the IPI handlers are fixed and hence
they don't involve costly operations such as adding IPI handlers to the target
CPU's function queue, acquiring locks for synchronization etc.
Luckily we have an unused IPI message slot, so use that to implement
tick broadcast IPIs efficiently.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[Functions renamed to tick_broadcast* and Changelog modified by
Preeti U. Murthy<preeti@linux.vnet.ibm.com>]
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoff@infradead.org> [For the PS3 part]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IPI handlers for both PPC_MSG_CALL_FUNC and PPC_MSG_CALL_FUNC_SINGLE map
to a common implementation - generic_smp_call_function_single_interrupt(). So,
we can consolidate them and save one of the IPI message slots, (which are
precious on powerpc, since only 4 of those slots are available).
So, implement the functionality of PPC_MSG_CALL_FUNC_SINGLE using
PPC_MSG_CALL_FUNC itself and release its IPI message slot, so that it can be
used for something else in the future, if desired.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoff@infradead.org> [For the PS3 part]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b8a9a11b9 (powerpc: eeh: Kill another abuse of irq_desc) is
missing some brackets .....
It's not a good idea to write patches in grumpy mode and then forget
to at least compile test them or rely on the few eyeballs discussing
that patch to spot it.....
Reported-by: fengguang.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: ppc <linuxppc-dev@lists.ozlabs.org>
commit 91150af3a (powerpc/eeh: Fix unbalanced enable for IRQ) is
another brilliant example of trainwreck engineering.
The patch "fixes" the issue of an unbalanced call to irq_enable()
which causes a prominent warning by checking the disabled state of the
interrupt line and call conditionally into the core code.
This is wrong in two aspects:
1) The warning is there to tell users, that they need to fix their
asymetric enable/disable patterns by finding the root cause and
solving it there.
It's definitely not meant to work around it by conditionally
calling into the core code depending on the random state of the irq
line.
Asymetric irq_disable/enable calls are a clear sign of wrong usage
of the interfaces which have to be cured at the root and not by
somehow hacking around it.
2) The abuse of core internal data structure instead of using the
proper interfaces for retrieving the information for the 'hack
around'
irq_desc is core internal and it's clear enough stated.
Replace at least the irq_desc abuse with the proper functions and add
a big fat comment why this is absurd and completely wrong.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: ppc <linuxppc-dev@lists.ozlabs.org>
Link: http://lkml.kernel.org/r/20140223212736.562906212@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: ppc <linuxppc-dev@lists.ozlabs.org>
Link: http://lkml.kernel.org/r/20140223212736.333718121@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I'm really grumpy about this one. The line:
#include "../../../kernel/irq/settings.h"
should have been an alarm sign for all people who added their SOB to
this trainwreck.
When I cleaned up the mess people made with interrupt descriptors a
few years ago, I warned that I'm going to hunt down new offenders and
treat them with stinking trouts. In this case I'll use frozen shark
for a better educational value.
The whole idiocy which was done there could have been avoided with two
lines of perfectly fine code. And do not complain about the lack of
correct examples in tree.
The solution is simple:
Remove the brainfart and use the proper functions, which should
have been used in the first place
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: ppc <linuxppc-dev@lists.ozlabs.org>
Link: http://lkml.kernel.org/r/20140223212736.451970660@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
