IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Tony notes that the GPIO module does not idle when level interrupts are
in use, as the wakeup appears to get stuck.
After extensive investigation, it appears that the wakeup will only be
cleared if the interrupt status register is cleared while the interrupt
is enabled. However, we are currently clearing it with the interrupt
disabled for level-based interrupts.
It is acknowledged that this observed behaviour conflicts with a
statement in the TRM:
CAUTION
After servicing the interrupt, the status bit in the interrupt status
register (GPIOi.GPIO_IRQSTATUS_0 or GPIOi.GPIO_IRQSTATUS_1) must be
reset and the interrupt line released (by setting the corresponding
bit of the interrupt status register to 1) before enabling an
interrupt for the GPIO channel in the interrupt-enable register
(GPIOi.GPIO_IRQSTATUS_SET_0 or GPIOi.GPIO_IRQSTATUS_SET_1) to prevent
the occurrence of unexpected interrupts when enabling an interrupt
for the GPIO channel.
However, this does not appear to be a practical problem.
Further, as reported by Grygorii Strashko <grygorii.strashko@ti.com>,
the TI Android kernel tree has an earlier similar patch as "GPIO: OMAP:
Fix the sequence to clear the IRQ status" saying:
if the status is cleared after disabling the IRQ then sWAKEUP will not
be cleared and gates the module transition
When we unmask the level interrupt after the interrupt has been handled,
enable the interrupt and only then clear the interrupt. If the interrupt
is still pending, the hardware will re-assert the interrupt status.
Should the caution note in the TRM prove to be a problem, we could
use a clear-enable-clear sequence instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: updated comments based on an earlier TI patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current amd_fch_gpio_direction_output implementation ignores the value
argument, fix it so direction_output will set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Enrico Weigelt <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was newly introduced but the version that got merged
produces a harmless compiler warning:
drivers/platform/x86/pcengines-apuv2.c: In function 'apu_board_init':
drivers/platform/x86/pcengines-apuv2.c:211:6: error: unused variable 'rc' [-Werror=unused-variable]
Remove the evidently useless variable.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-By: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 0cdf21b34e
("gpio: pca953x: set the PCA_PCAL flag also when matching by DT")
introduces a helper macro which tells that chip supports latched interrupts,
but the macro was never used for ACPI or legacy enumeration.
So, make use of it for legacy and ACPI enumeration.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently PINCTRL_IMX8QM and PINCTRL_IMX8QXP will select PINCTRL_IMX_SCU.
However, PINCTRL_IMX_SCU may not be valid due to it depends on IMX_MBOX.
Then we may meet the following link errors:
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinctrl_sc_ipc_init':
pinctrl-scu.c:(.text+0x10): undefined reference to `imx_scu_get_handle'
ld: pinctrl-scu.c:(.text+0x10): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_get_handle'
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_get_scu':
pinctrl-scu.c:(.text+0xa0): undefined reference to `imx_scu_call_rpc'
ld: pinctrl-scu.c:(.text+0xa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_set_scu':
pinctrl-scu.c:(.text+0x1b4): undefined reference to `imx_scu_call_rpc'
ld: pinctrl-scu.c:(.text+0x1b4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
ld: drivers/pinctrl/freescale/pinctrl-imx8qxp.o: in function `imx8qxp_pinctrl_probe':
pinctrl-imx8qxp.c:(.text+0x28): undefined reference to `imx_pinctrl_probe'
ld: pinctrl-imx8qxp.c:(.text+0x28): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_pinctrl_probe'
Rework so that PINCTRL_IMX8QM and PINCTRL_IMX8QXP depends on IMX_SCU
as well in case they're wrongly enabled.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge more updates from Andrew Morton:
- some of the rest of MM
- various misc things
- dynamic-debug updates
- checkpatch
- some epoll speedups
- autofs
- rapidio
- lib/, lib/lzo/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (83 commits)
samples/mic/mpssd/mpssd.h: remove duplicate header
kernel/fork.c: remove duplicated include
include/linux/relay.h: fix percpu annotation in struct rchan
arch/nios2/mm/fault.c: remove duplicate include
unicore32: stop printing the virtual memory layout
MAINTAINERS: fix GTA02 entry and mark as orphan
mm: create the new vm_fault_t type
arm, s390, unicore32: remove oneliner wrappers for memblock_alloc()
arch: simplify several early memory allocations
openrisc: simplify pte_alloc_one_kernel()
sh: prefer memblock APIs returning virtual address
microblaze: prefer memblock API returning virtual address
powerpc: prefer memblock APIs returning virtual address
lib/lzo: separate lzo-rle from lzo
lib/lzo: implement run-length encoding
lib/lzo: fast 8-byte copy on arm64
lib/lzo: 64-bit CTZ on arm64
lib/lzo: tidy-up ifdefs
ipc/sem.c: replace kvmalloc/memset with kvzalloc and use struct_size
ipc: annotate implicit fall through
...
The percpu member of this structure is declared as:
struct ... ** __percpu member;
So its type is:
__percpu pointer to pointer to struct ...
But looking at how it's used, its type should be:
pointer to __percpu pointer to struct ...
and it should thus be declared as:
struct ... * __percpu *member;
So fix the placement of '__percpu' in the definition of this
structures.
This silents a few Sparse's warnings like:
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3> *__vpp_verify
got struct sched_domain **
Link: http://lkml.kernel.org/r/20190118144902.79065-1-luc.vanoostenryck@gmail.com
Fixes: 017c59c042 ("relay: Use per CPU constructs for the relay channel buffer pointers")
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove linux/ptrace.h which is included more than once
Link: http://lkml.kernel.org/r/5c45d345.1c69fb81.d90ed.8e05@mx.google.com
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit ad67b74d24 ("printk: hash addresses printed with %p"),
the virtual memory layout printed during boot up contains "ptrval"
instead of actual addresses.
Instead of changing the printing to "%px", and leaking virtual memory
layout information again, just remove the printing completely, cfr.
e.g. commits 071929dbdd ("arm64: Stop printing the virtual memory
layout") and 31833332f7 ("m68k/mm: Stop printing the virtual memory
layout").
All interesting information (actual section sizes) is already printed by
mem_init_print_info() just above anyway.
Link: http://lkml.kernel.org/r/20190121152254.29079-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The entry for GTA02 never had paths listed; fix that. commit 9d76295ac6
("[ARM] GTA02/FreeRunner: Add machine definition"), which added the entry
for GTA02, created two new files named
arch/arm/mach-s3c2442/{include/mach/gta02.h,mach-gta02.c}, which were then
renamed in commit dd6f01b5cc ("ARM: S3C2440: move mach-s3c2440/* into
mach-s3c24xx/") to
arch/arm/mach-s3c24xx/{include/mach/gta02.h,mach-gta02.c}.
Also, the GTA02 maintainer's email address is from a domain that doesn't
have an MX record anymore and appears to have expired. Remove the
maintainer and mark the subsystem as orphan.
Link: http://lkml.kernel.org/r/20190215140444.37060-1-jannh@google.com
Signed-off-by: Jann Horn <jannh@google.com>
Cc: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Nelson Castillo <nelsoneci@gmail.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Page fault handlers are supposed to return VM_FAULT codes, but some
drivers/file systems mistakenly return error numbers. Now that all
drivers/file systems have been converted to use the vm_fault_t return
type, change the type definition to no longer be compatible with 'int'.
By making it an unsigned int, the function prototype becomes
incompatible with a function which returns int. Sparse will detect any
attempts to return a value which is not a VM_FAULT code.
VM_FAULT_SET_HINDEX and VM_FAULT_GET_HINDEX values are changed to avoid
conflict with other VM_FAULT codes.
[jrdr.linux@gmail.com: fix warnings]
Link: http://lkml.kernel.org/r/20190109183742.GA24326@jordon-HP-15-Notebook-PC
Link: http://lkml.kernel.org/r/20190108183041.GA12137@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arm, s390 and unicore32 use oneliner wrappers for memblock_alloc().
Replace their usage with direct call to memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-7-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several early memory allocations in arch/ code that use
memblock_phys_alloc() to allocate memory, convert the returned physical
address to the virtual address and then set the allocated memory to
zero.
Exactly the same behaviour can be achieved simply by calling
memblock_alloc(): it allocates the memory in the same way as
memblock_phys_alloc(), then it performs the phys_to_virt() conversion
and clears the allocated memory.
Replace the longer sequence with a simpler call to memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-6-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pte_alloc_one_kernel() function allocates a page using
__get_free_page(GFP_KERNEL) when mm initialization is complete and
memblock_phys_alloc() on the earlier stages. The physical address of
the page allocated with memblock_phys_alloc() is converted to the
virtual address and in the both cases the allocated page is cleared
using clear_page().
The code is simplified by replacing __get_free_page() with
get_zeroed_page() and by replacing memblock_phys_alloc() with
memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-5-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than use the memblock_alloc_base that returns a physical address
and then convert this address to the virtual one, use appropriate
memblock function that returns a virtual address.
There is a small functional change in the allocation of then
NODE_DATA(). Instead of panicing if the local allocation failed, the
non-local allocation attempt will be made.
Link: http://lkml.kernel.org/r/1546248566-14910-4-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than use the memblock_alloc_base that returns a physical address
and then convert this address to the virtual one, use appropriate
memblock function that returns a virtual address.
Link: http://lkml.kernel.org/r/1546248566-14910-3-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "memblock: simplify several early memory allocation", v4.
These patches simplify some of the early memory allocations by replacing
usage of older memblock APIs with newer and shinier ones.
Quite a few places in the arch/ code allocated memory using a memblock
API that returns a physical address of the allocated area, then
converted this physical address to a virtual one and then used memset(0)
to clear the allocated range.
More recent memblock APIs do all the three steps in one call and their
usage simplifies the code.
It's important to note that regardless of API used, the core allocation
is nearly identical for any set of memblock allocators: first it tries
to find a free memory with all the constraints specified by the caller
and then falls back to the allocation with some or all constraints
disabled.
The first three patches perform the conversion of call sites that have
exact requirements for the node and the possible memory range.
The fourth patch is a bit one-off as it simplifies openrisc's
implementation of pte_alloc_one_kernel(), and not only the memblock
usage.
The fifth patch takes care of simpler cases when the allocation can be
satisfied with a simple call to memblock_alloc().
The sixth patch removes one-liner wrappers for memblock_alloc on arm and
unicore32, as suggested by Christoph.
This patch (of 6):
There are a several places that allocate memory using memblock APIs that
return a physical address, convert the returned address to the virtual
address and frequently also memset(0) the allocated range.
Update these places to use memblock allocators already returning a
virtual address. Use memblock functions that clear the allocated memory
instead of calling memset(0) where appropriate.
The calls to memblock_alloc_base() that were not followed by memset(0)
are replaced with memblock_alloc_try_nid_raw(). Since the latter does
not panic() when the allocation fails, the appropriate panic() calls are
added to the call sites.
Link: http://lkml.kernel.org/r/1546248566-14910-2-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Salter <msalter@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To prevent any issues with persistent data, separate lzo-rle from lzo so
that it is treated as a separate algorithm, and lzo is still available.
Link: http://lkml.kernel.org/r/20190205155944.16007-3-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Cc: Matt Sealey <matt.sealey@arm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <nitingupta910@gmail.com>
Cc: Richard Purdie <rpurdie@openedhand.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Sonny Rao <sonnyrao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "lib/lzo: run-length encoding support", v5.
Following on from the previous lzo-rle patchset:
https://lkml.org/lkml/2018/11/30/972
This patchset contains only the RLE patches, and should be applied on
top of the non-RLE patches ( https://lkml.org/lkml/2019/2/5/366 ).
Previously, some questions were raised around the RLE patches. I've
done some additional benchmarking to answer these questions. In short:
- RLE offers significant additional performance (data-dependent)
- I didn't measure any regressions that were clearly outside the noise
One concern with this patchset was around performance - specifically,
measuring RLE impact separately from Matt Sealey's patches (CTZ & fast
copy). I have done some additional benchmarking which I hope clarifies
the benefits of each part of the patchset.
Firstly, I've captured some memory via /dev/fmem from a Chromebook with
many tabs open which is starting to swap, and then split this into 4178
4k pages. I've excluded the all-zero pages (as zram does), and also the
no-zero pages (which won't tell us anything about RLE performance).
This should give a realistic test dataset for zram. What I found was
that the data is VERY bimodal: 44% of pages in this dataset contain 5%
or fewer zeros, and 44% contain over 90% zeros (30% if you include the
no-zero pages). This supports the idea of special-casing zeros in zram.
Next, I've benchmarked four variants of lzo on these pages (on 64-bit
Arm at max frequency): baseline LZO; baseline + Matt Sealey's patches
(aka MS); baseline + RLE only; baseline + MS + RLE. Numbers are for
weighted roundtrip throughput (the weighting reflects that zram does
more compression than decompression).
https://drive.google.com/file/d/1VLtLjRVxgUNuWFOxaGPwJYhl_hMQXpHe/view?usp=sharing
Matt's patches help in all cases for Arm (and no effect on Intel), as
expected.
RLE also behaves as expected: with few zeros present, it makes no
difference; above ~75%, it gives a good improvement (50 - 300 MB/s on
top of the benefit from Matt's patches).
Best performance is seen with both MS and RLE patches.
Finally, I have benchmarked the same dataset on an x86-64 device. Here,
the MS patches make no difference (as expected); RLE helps, similarly as
on Arm. There were no definite regressions; allowing for observational
error, 0.1% (3/4178) of cases had a regression > 1 standard deviation,
of which the largest was 4.6% (1.2 standard deviations). I think this
is probably within the noise.
https://drive.google.com/file/d/1xCUVwmiGD0heEMx5gcVEmLBI4eLaageV/view?usp=sharing
One point to note is that the graphs show RLE appears to help very
slightly with no zeros present! This is because the extra code causes
the clang optimiser to change code layout in a way that happens to have
a significant benefit. Taking baseline LZO and adding a do-nothing line
like "__builtin_prefetch(out_len);" immediately before the "goto next"
has the same effect. So this is a real, but basically spurious effect -
it's small enough not to upset the overall findings.
This patch (of 3):
When using zram, we frequently encounter long runs of zero bytes. This
adds a special case which identifies runs of zeros and encodes them
using run-length encoding.
This is faster for both compression and decompresion. For high-entropy
data which doesn't hit this case, impact is minimal.
Compression ratio is within a few percent in all cases.
This modifies the bitstream in a way which is backwards compatible
(i.e., we can decompress old bitstreams, but old versions of lzo cannot
decompress new bitstreams).
Link: http://lkml.kernel.org/r/20190205155944.16007-2-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Cc: Matt Sealey <matt.sealey@arm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <nitingupta910@gmail.com>
Cc: Richard Purdie <rpurdie@openedhand.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Sonny Rao <sonnyrao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LZO leaves some performance on the table by not realising that arm64 can
optimize count-trailing-zeros bit operations.
Add CONFIG_ARM64 to the checked definitions alongside CONFIG_X86_64 to
enable the use of rbit/clz instructions on full 64-bit quantities.
Link: http://lkml.kernel.org/r/20181127161913.23863-5-dave.rodgman@arm.com
Link: http://lkml.kernel.org/r/20190205141950.9058-3-dave.rodgman@arm.com
Signed-off-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <nitingupta910@gmail.com>
Cc: Richard Purdie <rpurdie@openedhand.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Sonny Rao <sonnyrao@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "lib/lzo: performance improvements", v5.
This patch (of 3):
Modify the ifdefs in lzodefs.h to be more consistent with normal kernel
macros (e.g., change __aarch64__ to CONFIG_ARM64).
Link: http://lkml.kernel.org/r/20190205141950.9058-2-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nitin Gupta <nitingupta910@gmail.com>
Cc: Richard Purdie <rpurdie@openedhand.com>
Cc: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Sonny Rao <sonnyrao@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matt Sealey <matt.sealey@arm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kvzalloc() instead of kvmalloc() and memset().
Also, make use of the struct_size() helper instead of the open-coded
version in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle.
Link: http://lkml.kernel.org/r/20190131214221.GA28930@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and this
place in the code produced a warning (W=1).
This commit remove the following warning:
ipc/sem.c:1683:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Link: http://lkml.kernel.org/r/20190114203608.18218-1-malat@debian.org
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When booting an allmodconfig kernel, there are a lot of false-positives.
With a message like this 'UBSAN: Undefined behaviour in...' with a call
trace that follows.
UBSAN warnings are a result of enabling noisy CONFIG_UBSAN_ALIGNMENT
which is disabled by default if HAVE_EFFICIENT_UNALIGNED_ACCESS=y.
It's noisy even if don't have efficient unaligned access, e.g. people
often add __cacheline_aligned_in_smp in structs, but forget to align
allocations of such struct (kmalloc() give 8-byte alignment in worst
case).
Rework so that when building a allmodconfig kernel that turns everything
into '=m' or '=y' will turn off UBSAN_ALIGNMENT.
[aryabinin@virtuozzo.com: changelog addition]
Link: http://lkml.kernel.org/r/20181217150326.30933-1-anders.roxell@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 1751e8a6cb ("Rename superblock flags (MS_xyz ->
SB_xyz)"), scripts/gdb should be updated to replace MS_xyz with SB_xyz.
This change didn't directly affect the running operation of scripts/gdb
until commit e262e32d6b "vfs: Suppress MS_* flag defs within the
kernel unless explicitly enabled" removed the definitions used by
constants.py.
Update constants.py.in to utilise the new internal flags, matching the
implementation at fs/proc_namespace.c::show_sb_opts.
Note to stable, e262e32d6b landed in v5.0-rc1 (which was just
released), so we'll want this picked back to 5.0 stable once this patch
hits mainline (akpm just picked it up). Without this, debugging a
kernel a kernel via GDB+QEMU is broken in the 5.0 release.
[kieran.bingham@ideasonboard.com: add fixes tag, reword commit message]
Link: http://lkml.kernel.org/r/20190305103014.25847-1-kieran.bingham@ideasonboard.com
Fixes: e262e32d6b "vfs: Suppress MS_* flag defs within the kernel unless explicitly enabled"
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Dan Robertson <danlrobertson89@gmail.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided refcount_t
type and API that prevents accidental counter overflows and underflows.
This is important since overflows and underflows can lead to
use-after-free situation and be exploitable.
The variable kcov.refcount is used as pure reference counter. Convert
it to refcount_t and fix up the operations.
**Important note for maintainers:
Some functions from refcount_t API defined in lib/refcount.c have
different memory ordering guarantees than their atomic counterparts.
The full comparison can be seen in https://lkml.org/lkml/2017/11/15/57
and it is hopefully soon in state to be merged to the documentation
tree. Normally the differences should not matter since refcount_t
provides enough guarantees to satisfy the refcounting use cases, but in
some rare cases it might matter. Please double check that you don't
have some undocumented memory guarantees for this variable usage.
For the kcov.refcount it might make a difference
in following places:
- kcov_put(): decrement in refcount_dec_and_test() only
provides RELEASE ordering and control dependency on success
vs. fully ordered atomic counterpart
Link: http://lkml.kernel.org/r/1547634429-772-1-git-send-email-elena.reshetova@intel.com
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: http://lkml.kernel.org/r/20190122152151.16139-46-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This slightly optimizes the kernel/configs.c build.
bin2c is not very efficient because it converts a data file into a huge
array to embed it into a *.c file.
Instead, we can use the .incbin directive.
Also, this simplifies the code; Makefile is cleaner, and the way to get
the offset/size of the config_data.gz is more straightforward.
I used the "asm" statement in *.c instead of splitting it into *.S
because MODULE_* tags are not supported in *.S files.
I also cleaned up kernel/.gitignore; "config_data.gz" is unneeded
because the top-level .gitignore takes care of the "*.gz" pattern.
[yamada.masahiro@socionext.com: v2]
Link: http://lkml.kernel.org/r/1550108893-21226-1-git-send-email-yamada.masahiro@socionext.com
Link: http://lkml.kernel.org/r/1549941160-8084-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Popov <alex.popov@linux.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This Kconfig option was removed during v4.19 development in commit
771c035372 ("deprecate the '__deprecated' attribute warnings entirely
and for good") so there's no point to keep it in defconfigs any longer.
FWIW defconfigs were patched with:
--------------------------->8----------------------
find . -name *_defconfig -exec sed -i '/CONFIG_ENABLE_WARN_DEPRECATED/d' {} \;
--------------------------->8----------------------
Link: http://lkml.kernel.org/r/20190128152434.41969-1-abrodkin@synopsys.com
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Link: http://lkml.kernel.org/r/20190109172445.GA15908@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, when writing
echo 18446744073709551616 > /proc/sys/fs/file-max
/proc/sys/fs/file-max will overflow and be set to 0. That quickly
crashes the system.
This commit sets the max and min value for file-max. The max value is
set to long int. Any higher value cannot currently be used as the
percpu counters are long ints and not unsigned integers.
Note that the file-max value is ultimately parsed via
__do_proc_doulongvec_minmax(). This function does not report error when
min or max are exceeded. Which means if a value largen that long int is
written userspace will not receive an error instead the old value will be
kept. There is an argument to be made that this should be changed and
__do_proc_doulongvec_minmax() should return an error when a dedicated min
or max value are exceeded. However this has the potential to break
userspace so let's defer this to an RFC patch.
Link: http://lkml.kernel.org/r/20190107222700.15954-3-christian@brauner.io
Signed-off-by: Christian Brauner <christian@brauner.io>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Waiman Long <longman@redhat.com>
[christian@brauner.io: v4]
Link: http://lkml.kernel.org/r/20190210203943.8227-3-christian@brauner.io
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_get_long() is a funny function. It uses simple_strtoul() and for a
good reason. proc_get_long() wants to always succeed the parse and
return the maybe incorrect value and the trailing characters to check
against a pre-defined list of acceptable trailing values. However,
simple_strtoul() explicitly ignores overflows which can cause funny
things like the following to happen:
echo 18446744073709551616 > /proc/sys/fs/file-max
cat /proc/sys/fs/file-max
0
(Which will cause your system to silently die behind your back.)
On the other hand kstrtoul() does do overflow detection but does not
return the trailing characters, and also fails the parse when anything
other than '\n' is a trailing character whereas proc_get_long() wants to
be more lenient.
Now, before adding another kstrtoul() function let's simply add a static
parse strtoul_lenient() which:
- fails on overflow with -ERANGE
- returns the trailing characters to the caller
The reason why we should fail on ERANGE is that we already do a partial
fail on overflow right now. Namely, when the TMPBUFLEN is exceeded. So
we already reject values such as 184467440737095516160 (21 chars) but
accept values such as 18446744073709551616 (20 chars) but both are
overflows. So we should just always reject 64bit overflows and not
special-case this based on the number of chars.
Link: http://lkml.kernel.org/r/20190107222700.15954-2-christian@brauner.io
Signed-off-by: Christian Brauner <christian@brauner.io>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Waiman Long <longman@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/rapidio/devices/rio_mport_cdev.c: In function `mport_release_mapping':
drivers/rapidio/devices/rio_mport_cdev.c:2151:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
rio_unmap_inb_region(mport, map->phys_addr);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
CC drivers/regulator/fixed-helper.o
CC drivers/pinctrl/stm32/pinctrl-stm32f429.o
drivers/rapidio/devices/rio_mport_cdev.c:2152:2: note: here
case MAP_DMA:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Link: http://lkml.kernel.org/r/20190212175014.GA14326@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Alexandre Bounine <alex.bou9@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If riocm_get_channel() fails, then we should just return -EINVAL.
Calling riocm_put_channel() will trigger a NULL dereference and
generally we should call put() if the get() didn't succeed.
Link: http://lkml.kernel.org/r/20190110130230.GB27017@kadam
Fixes: b6e8d4aa11 ("rapidio: add RapidIO channelized messaging driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function can only be called safely from very specific scheduler
contexts. Document those.
Link: http://lkml.kernel.org/r/20190206150528.31198-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Large enterprise clients often run applications out of networked file
systems where the IT mandated layout of project volumes can end up
leading to paths that are longer than 128 characters. Bumping this up
to the next order of two solves this problem in all but the most
egregious case while still fitting into a 512b slab.
[oleg@redhat.com: update comment, per Kees]
Link: http://lkml.kernel.org/r/20181112160956.GA28472@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Ben Woodard <woodard@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now splice() on O_DIRECT-opened fat file will return -EFAULT, that is
because the default .splice_write, namely default_file_splice_write(),
will construct an ITER_KVEC iov_iter and dio_refill_pages() in dio path
can not handle it.
Fix it by implementing .splice_write through iter_file_splice_write().
Spotted by xfs-tests generic/091.
Link: http://lkml.kernel.org/r/20190210094754.56355-1-houtao1@huawei.com
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
autofs does not expect the pipe it is given to have O_NONBLOCK set -
specifically if __kernel_write() in autofs_write() returns -EAGAIN, this
is treated as a fatal error and the pipe is closed.
For safety autofs should, therefore, clear the O_NONBLOCK flag.
Releases of systemd prior to 8th February 2019 used
pipe2(p, O_NONBLOCK|O_CLOEXEC)
and thus (inadvertently) set this flag.
Link: http://lkml.kernel.org/r/154993550902.3321.1183632970046073478.stgit@pluto-themaw-net
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix checkpatch.sh WARNING about the use of seq_printf() to print simple
strings in autofs_show_options(), use seq_puts() in this case.
Link: http://lkml.kernel.org/r/154889012613.4863.12231175554744203482.stgit@pluto-themaw-net
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an autofs file system mount option that can be used to provide a
generic indicator to applications that the mount entry should be ignored
when displaying mount information.
In other OSes that provide autofs and that provide a mount list to user
space based on the kernel mount list a no-op mount option ("ignore" is
the one use on the most common OS) is allowed so that autofs file system
users can optionally use it.
The idea is that it be used by user space programs to exclude autofs
mounts from consideration when reading the mounts list.
Prior to the change to link /etc/mtab to /proc/self/mounts all I needed
to do to achieve this was to use mount(2) and not update the mtab but
now that no longer works.
I know the symlinking happened a long time ago and I considered doing
this then but, at the time I couldn't remember the commonly used option
name and thought persuading the various utility maintainers would be too
hard.
But now I have a RHEL request to do this for compatibility for a widely
used product so I want to go ahead with it and try and enlist the help
of some utility package maintainers.
Clearly, without the option nothing can be done so it's at least a
start.
Link: http://lkml.kernel.org/r/154725123970.11260.6113771566924907275.stgit@pluto-themaw-net
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sparse issues a warning:
CHECK init/calibrate.c
init/calibrate.c:271:28: warning: symbol 'calibration_delay_done' was not declared. Should it be static?
The actual issue is that it's a __weak symbol that archs can override
(in fact, ARM does so), but no prototype is provided. Let's provide one
to prevent surprises.
Link: http://lkml.kernel.org/r/18827.1548750938@turing-police.cc.vt.edu
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Number of ELF program headers is 16-bit by spec, so total size
comfortably fits into "unsigned int".
Space savings: 7 bytes!
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-7 (-7)
Function old new delta
load_elf_phdrs 137 130 -7
Link: http://lkml.kernel.org/r/20190204202715.GA27482@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
