IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Remove dead code inside #if 0 conditionals.
Remove the #ifdef __KERNEL__ test, since NCR5380.h has no definitions
that relate to userspace code.
Remove two redundant macro definitions which were overlooked in
commit e9db3198e0 ("sun3_scsi: Adopt NCR5380.c core driver").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DIFFERENTIAL and PARITY option macros are unused: no supported
hardware uses differential signalling and the core driver never
implemented parity checking. These options just waste space in the host
info string.
While we are here, fix a typo in the NCR5380_info() kernel-doc comment.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use standard probe_irq_on() and probe_irq_off() functions instead of own
implementation. This prevents warning messages like this in the kernel
log: genirq: Flags mismatch irq 1. 00000000 (NCR-probe) vs. 00000080
(i8042)
Move the IRQ trigger code from NCR5380 to g_NCR5380 where it is used.
Also clear interrupt flag before and after the probe.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Apply prototypes to get consistent function signatures for the DMA
functions implemented in the board-specific drivers. To avoid using
macros to alter actual parameters, some of those functions are reworked
slightly.
This is a step toward the goal of passing the board-specific routines
to the core driver using an ops struct (as in a platform driver or
library module).
This also helps fix some inconsistent types: where the core driver uses
ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of
transfers, certain board-specific routines used unsigned long.
While we are fixing these function signatures, pass the hostdata pointer
to DMA routines instead of a Scsi_Host pointer, for shorter and faster
code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the call to NCR5380_poll_politely2() when possible. The call is
easily short-circuited on the PIO fast path, using the inline wrapper.
This requires that the NCR5380_read macro be made available before
any #include "NCR5380.h" so a few declarations have to be moved too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass a NCR5380_hostdata struct pointer to the board-specific routines
instead of a Scsi_Host struct pointer. This reduces pointer chasing in
the PIO and PDMA fast paths. The old way was a mistake because it is
slow and the board-specific code is not concerned with the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For timeout values adopt unsigned long, which is the type of jiffies etc.
For chip register values and bit masks pass u8, which is the return type
of readb, inb etc.
For device register offsets adopt unsigned int, as it is suitable for
adding to base addresses.
Pass the NCR5380_hostdata pointer to the board-specific routines instead
of the Scsi_Host pointer. The board-specific code is concerned with
hardware and not with SCSI protocol or the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The various 5380 drivers inconsistently store register pointers
either in the Scsi_Host struct "legacy crap" area or in special,
board-specific members of the NCR5380_hostdata struct. Uniform
use of the latter struct makes for simpler and faster code (see
the following patches) and helps to reduce use of the
NCR5380_implementation_fields macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Re-order struct members so that hot data lies at the beginning of the
struct and cold data at the end. Improve the comments while we're here.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If NCR5380_poll_politely() is called under irq lock, the polling time
limit is clamped to avoid a spike in interrupt latency. When not under
irq lock, the same polling time limit acts as the worst case delay
between schedule() calls.
During PDMA (under irq lock) I've found that the 10 ms time limit is
sometimes too short, and leads to the error message,
sd 0:0:0:0: [sda] tag#1 macscsi_pread: !REQ and !ACK
This particular target identifies itself as a QUANTUM DAYTONA514S. It
seems to be slower to assert ACK than the other targets I've tested.
This patch solves the problem by increasing the polling timeout.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When polling a device register under irq lock the polling loop terminates
after a given number of jiffies. Make this timeout independent of the HZ
setting.
All 5380 drivers benefit from this patch, which optimizes the PIO fast
path, because they all use PIO transfers (for phases other than DATA IN
and DATA OUT). Some cards support only PIO transfers (even for DATA
phases). CPU cycles are scarce on some of these systems, so a small
improvement here makes a big difference.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large PIO transfers are broken up into chunks to try to avoid disabling
local IRQs for long periods. But IRQs are still disabled for too long
and this causes SCC FIFO overruns during serial port transfers.
This patch reduces the PIO chunk size to reduce interrupt latency to
something on the order of milliseconds, at the expense of additional CPU
overhead from extra iterations of the NCR5380_main() loop.
That CPU overhead is a problem for slow machines (e.g. mac_scsi on 25
MHz 68030) but these machines generally use PDMA not PIO. This patch
doesn't make the overhead any worse on my Mac LC III (because it only
gets about 510 accesses per ms).
This patch decreases disk performance by a fraction of one percent for
dmx3191d on my 333 MHz PowerPC 750. Other affected hardware (such as
g_NCR5380 on x86) was not tested but 5380 ISA cards generally use PDMA
and not PIO.
[mkp: fix whitespace]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
some versions of gcc now warn:
In file included from drivers/scsi/mac_scsi.c:335:
drivers/scsi/NCR5380.h:295: warning: `NCR5380_poll_politely' declared inline after being called
drivers/scsi/NCR5380.h:295: warning: previous declaration of `NCR5380_poll_politely' was here
Avoid this by defining NCR5380_poll_politely() in NCR5380.h.
[mkp: checkpatch warnings]
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix various issues: Comments about bus errors are incorrect. The
PDMA asm must return the size of the memory access that faulted so the
transfer count can be adjusted accordingly. A phase change may cause a
bus error but should not be treated as failure. A bus error does not
always imply a phase change and generally the transfer may continue.
Scatter/gather doesn't seem to work with PDMA due to overruns. This is
a pity because peak throughput seems to double with SG_ALL.
Tested on a Mac LC III and a PowerBook 520.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c
core driver, remove atari_NCR5380.c. Also remove the last vestiges of its
Tagged Command Queueing implementation from the wrapper drivers.
The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not
merged into the remaining core driver because,
1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled
by default, which indicates that it is mostly undesirable.
2) I'm told that it doesn't work correctly when enabled.
3) The algorithm does not make use of block layer tags which it will have
to do because scmd->tag is deprecated.
4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS
macro interacts with the CONFIG_SUN3 macro in 'interesting' ways.
5) Compile-time configuration with macros like SUPPORT_TAGS caused the
configuration space to explode, leading to untestable and unmaintainable
code that is too hard to reason about.
The merge_contiguous_buffers() code is also abandoned. This was unused
by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT
supports scatter/gather. I suspect that the TT would work fine with
ENABLE_CLUSTERING instead. If someone can benchmark the difference then
perhaps the merge_contiguous_buffers() code can be be justified. Until
then we are better off without the extra complexity.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For those wrapper drivers which only implement Programmed IO, have
NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily
disabled at run-time and so the PSEUDO_DMA macro is no longer needed.
Also remove the spin counters used for debugging pseudo DMA drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only chip that needs the workarounds enabled is an early NMOS
device. That means that the common case is to disable them.
Unfortunately the sense of the flag is such that it has to be set
for the common case.
Rename the flag so that zero can be used to mean "no errata workarounds
needed". This simplifies the code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the NCR5380.c core driver, these macros are never used.
If REAL_DMA were to be defined, compilation would fail.
For the atari_NCR5380.c core driver, REAL_DMA is always defined.
Hence these macros are pointless.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert compile-time C400_ register mapping to runtime mapping.
This removes the weird negative register offsets and allows adding
additional mappings.
While at it, convert read/write loops into insb/outsb.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During arbitration and selection, the relevant command is invisible to
exception handlers and can be found only in a pointer on the stack of a
different thread.
When eh_abort_handler can't find a given command, it can't decide whether
that command was completed already or is still in arbitration or selection
phase. But it must return either SUCCESS (e.g. command completed earlier)
or FAILED (could not abort the nexus, try bus reset).
The solution is to make sure all commands belonging to the LLD are always
visible to exception handlers. Add another scsi_cmnd pointer to the
hostdata struct to track the command in arbitration or selection phase.
Replace 'retain_dma_irq' with the new 'selecting' pointer, to bring
atari_NCR5380.c into line with NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_information_transfer() may re-queue a command for autosense,
after calling scsi_eh_prep_cmnd(). This creates several possibilities:
1. Reselection may intervene before the re-queued command gets processed.
If the reconnected command then undergoes autosense, this causes the
scsi_eh_save data from the previous command to be overwritten.
2. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
a new REQUEST SENSE command may arrive. This would be queued ahead
of any command already undergoing autosense, which means the
scsi_eh_save data might be restored to the wrong command.
3. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
eh_abort_handler() may abort the command. But the scsi_eh_save data is
not discarded, which means the scsi_eh_save data might be incorrectly
restored to the next REQUEST SENSE command issued.
This patch adds a new autosense list so that commands that are re-queued
because of a CHECK CONDITION result can be kept apart from the REQUEST
SENSE commands that arrive via queuecommand.
This patch also adds a function dedicated to dequeueing and preparing the
next command for processing. By refactoring the main loop in this way,
scsi_eh_save takes place when an autosense command is dequeued rather
than when re-queued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NCR5380 drivers have a home-spun linked list implementation for
scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt
the standard list_head data structure and list operations instead. Remove
the eh_abort_handler rather than convert it. Doing the conversion would
only be churn because the existing EH handlers don't work and get replaced
in a subsequent patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hostdata struct is now protected by a spin lock so the volatile
qualifiers are redundant. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace all H_NO and some HOSTNO macros (both peculiar to atari_NCR5380.c)
with a new dsprintk macro that's more useful and more consistent. The new
macro avoids a lot of boilerplate in new code in subsequent patches. Keep
NCR5380.c in sync. Remaining HOSTNO macros are removed as side-effects
of subsequent patches.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c presently uses the instance->host_lock spin lock. Convert this
to a new spin lock that protects the NCR5380_hostdata struct.
atari_NCR5380.c previously used local_irq_save/restore() rather than a
spin lock. Convert this to hostdata->lock in irq mode. For SMP platforms,
the interrupt handler now also acquires the spin lock.
This brings all locking in the two core drivers into agreement.
Adding this locking also means that a bunch of volatile qualifiers can be
removed from the members of the NCR5380_hostdata struct. This is done in
a subsequent patch.
Proper locking will allow the abort handler to locate a command being
aborted. This is presently impossible if the abort handler is invoked when
the command has been moved from a queue to a pointer on the stack. (If
eh_abort_handler can't determine whether a command has been completed
or is still being processed then it can't decide whether to return
success or failure.)
The hostdata spin lock is now held when calling NCR5380_select() and
NCR5380_information_transfer(). Where possible, the lock is dropped for
polling and PIO transfers.
Clean up the now-redundant SELECT_ENABLE_REG writes, that used to provide
limited mutual exclusion between information_transfer() and reselect().
Accessing hostdata->connected without data races means taking the lock;
cleanup these accesses.
The new spin lock falls away for m68k and other UP builds, so this should
have little impact there. In the SMP case the new lock should be
uncontested even when the SCSI bus is contested.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove FLAG_DTC3181E. It was used to suppress a final Arbitration Lost
(SEL asserted) test that isn't actually needed. The test was suppressed
because it causes problems for DTC436 and DTC536 chips. It takes place
after the host wins arbitration, so SEL has been asserted. These chips
can't seem to tell whether it was the host or another bus device that
did so.
This questionable final test appears in a flow chart in an early NCR5380
datasheet. It was removed from later documents like the DP5380 datasheet.
By the time this final test takes place, the driver has already tested
the Arbitration Lost bit several times. The first test happens 3 us after
BUS FREE (or longer due to register access delays). The protocol requires
that a device stop signalling within 1.8 us after BUS FREE unless it won
arbitration, in which case it must assert SEL, which is detected 1.2 us
later by the first Arbitration Lost test.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The flags DMA_WORKS_RIGHT, FLAG_NCR53C400 and FLAG_HAS_LAST_BYTE_SENT
all mean the same thing, i.e. the chip is not a 538[01]. (More recent
devices such as the 53C80 have a 'Last Byte Sent' bit in the Target
Command Register as well as other fixes for End-of-DMA errata.)
These flags have no additional meanings since previous cleanup patches
eliminated the NCR53C400 macro, moved g_NCR5380-specific code out of the
core driver and standardized interrupt handling.
Use the FLAG_NO_DMA_FIXUP flag to suppress End-of-DMA errata workarounds,
for those cards and drivers that make use of the TCR_LAST_BYTE_SENT bit.
Remove the old flags.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The complex main_running/queue_main mechanism is peculiar to
atari_NCR5380.c. It isn't SMP safe and offers little value given that
the work queue already offers concurrency management. Remove this
complexity to bring atari_NCR5380.c closer to NCR5380.c.
It is not a good idea to call the information transfer state machine from
queuecommand because, according to Documentation/scsi/scsi_mid_low_api.txt
that could happen in soft irq context. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each host instance now has it's own work queue so the main() work item can
sleep when necessary. That means we can use a simple work item rather than
a delayed work item. This brings NCR5380.c closer to atari_NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The atari_NCR5380.c and NCR5380.c core drivers differ in their handling of
target disconnection. This is partly because atari_NCR5380.c had all of
the polling and sleeping removed to become entirely interrupt-driven, and
it is partly because of damage done to NCR5380.c after atari_NCR5380.c was
forked. See commit 37cd23b44929 ("Linux 2.1.105") in history/history.git.
The polling changes that were made in v2.1.105 are questionable at best:
if REQ is not already asserted when NCR5380_transfer_pio() is invoked, and
if the expected phase is DATA IN or DATA OUT, the function will schedule
main() to execute after USLEEP_SLEEP jiffies and then return. The problems
here are the expected REQ timing and the sleep interval*. Avoid this issue
by using NCR5380_poll_politely() instead of scheduling main().
The atari_NCR5380.c core driver requires the use of the chip interrupt and
always permits target disconnection. It sets the cmd->device->disconnect
flag when a device disconnects, but never tests this flag.
The NCR5380.c core driver permits disconnection only when
instance->irq != NO_IRQ. It sets the cmd->device->disconnect flag when
a device disconnects and it tests this flag in a couple of places:
1. During NCR5380_information_transfer(), following COMMAND OUT phase,
if !cmd->device->disconnect, the initiator will take a guess as to
whether or not the target will then choose to go to MESSAGE IN phase
and disconnect. If the driver guesses "yes", it will schedule main()
to execute after USLEEP_SLEEP jiffies and then return there.
Unfortunately the driver may guess "yes" even after it has denied
the target the disconnection privilege. When the target does not
disconnect, the sleep can be beneficial, assuming the sleep interval
is appropriate (mostly it is not*).
And even if the driver guesses "yes" correctly, and the target would
then disconnect, the driver still has to go through the MESSAGE IN
phase in order to get to BUS FREE phase. The main loop can do nothing
useful until BUS FREE, and sleeping just delays the phase transition.
2. If !cmd->device->disconnect and REQ is not already asserted when
NCR5380_information_transfer() is invoked, the function polls for REQ
for USLEEP_POLL jiffies. If REQ is not asserted, it then schedules
main() to execute after USLEEP_SLEEP jiffies and returns.
The idea is apparently to yeild the CPU while waiting for REQ.
This is conditional upon !cmd->device->disconnect, but there seems
to be no rhyme or reason for that. For example, the flag may be
unset because disconnection privilege was denied because the driver
has no IRQ. Or the flag may be unset because the device has never
needed to disconnect before. Or if the flag is set, disconnection
may have no relevance to the present bus phase.
Another deficiency of the existing algorithm is as follows. When the
driver has no IRQ, it prevents disconnection, and generally polls and
sleeps more than it would normally. Now, if the driver is going to poll
anyway, why not allow the target to disconnect? That way the driver can do
something useful with the bus instead of polling unproductively!
Avoid this pointless latency, complexity and guesswork by using
NCR5380_poll_politely() instead of scheduling main().
* For g_NCR5380, the time intervals for USLEEP_SLEEP and USLEEP_POLL are
200 ms and 10 ms, respectively. They are 20 ms and 200 ms respectively
for the other NCR5380 drivers. There doesn't seem to be any reason for
this discrepancy. The timing seems to have no relation to the type of
adapter. Bizarrely, the timing in g_NCR5380 seems to relate only to one
particular type of target device. This patch attempts to solve the
problem for all NCR5380 drivers and all target devices.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux v2.1.105 changed the algorithm for polling for the BSY signal
in NCR5380_select() and NCR5380_main().
Presently, this code has a bug. Back then, NCR5380_set_timer(hostdata, 1)
meant reschedule main() after sleeping for 10 ms. Repeated 25 times this
provided the recommended 250 ms selection time-out delay. This got broken
when HZ became configurable.
We could fix this but there's no need to reschedule the main loop. This
BSY polling presently happens when the NCR5380_main() work queue item
calls NCR5380_select(), which in turn schedules NCR5380_main(), which
calls NCR5380_select() again, and so on.
This algorithm is a deviation from the simpler one in atari_NCR5380.c.
The extra complexity and state is pointless. There's no reason to
stop selection half-way and return to to the main loop when the main
loop can do nothing useful until selection completes.
So just poll for BSY. We can sleep while polling now that we have a
suitable workqueue.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in process context, sleep during polling if doing so won't add
significant latency. In interrupt context or if the lock is held, poll
briefly then give up. Keep both core drivers in sync.
Calibrate busy-wait iterations to allow for variation in chip register
access times between different 5380 hardware implementations.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate a work queue that will permit busy waiting and sleeping. This
means NCR5380_init() can potentially fail, so add this error path.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the restart_select and targets_present variables introduced in
Linux v1.1.38. The former was used only for a questionable debug printk
and the latter "so we can call a select failure a retryable condition".
Well, retrying select failure in general is a different problem to a
target that doesn't assert BSY. We need to handle these two cases
differently; the latter case can be left to the SCSI ML.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The aborted flag was introduced in v1.1.38 but never used. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.
Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.
Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().
This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.
The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch splits the NCR5380_init() function into two parts, similar
to the scheme used with atari_NCR5380.c. This avoids two problems.
Firstly, NCR5380_init() may perform a bus reset, which would cause the
chip to assert IRQ. The chip is unable to mask its bus reset interrupt.
Drivers can't call request_irq() before calling NCR5380_init(), because
initialization must happen before the interrupt handler executes. If
driver initialization causes an interrupt it may be problematic on some
platforms. To avoid that, first move the bus reset code into
NCR5380_maybe_reset_bus().
Secondly, NCR5380_init() contains some board-specific interrupt setup code
for the NCR53C400 that does not belong in the core driver. In moving this
code, better not re-order interrupt initialization and bus reset. Again,
the solution is to move the bus reset code into NCR5380_maybe_reset_bus().
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ASM macro is never defined. rtrc in pas16.c is not used.
NCR5380_map_config, do_NCR5380_intr, do_t128_intr and do_pas16_intr
are unused. NCR_NOT_SET harms readability. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike NCR5380.c, the atari_NCR5380.c core driver is limited to a single
instance because co-routine state is stored globally.
Fix this by removing the static scsi host pointer. For the co-routine,
obtain this pointer from the work_struct pointer instead. For the interrupt
handler, obtain it from the dev_id argument.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The atari_NCR5380.c core driver keeps some per-host data in a static
variable which limits the driver to a single instance. Fix this by moving
TagAlloc to the hostdata struct.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The static variable setup_use_tagged_queuing is declared in mac_scsi.c,
sun3_scsi.c and atari_scsi.c and doesn't belong in the core driver.
None of the other NCR5380 drivers suffer from this layering issue which
makes merging the core drivers more difficult and will likely hinder plans
for future use of platform data to configure the driver.
Replace the static variable with a host flag. This way it can be reported
along with the other flags.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make the atari_NCR5380.c core driver usable by sun3_scsi, mac_scsi and
others by moving some of the Falcon-specific code out of the core driver:
!IS_A_TT, atari_read_overruns and falcon_dont_release. Replace these with
hostdata variables and flags. FLAG_CHECK_LAST_BYTE_SENT is unused in
atari_NCR5380.c so don't set it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h".
The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting
the other core drivers reduces the diff which makes them easier to unify.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The *_RELEASE macros don't tell me anything. In some cases the version in
the macro contradicts the version in the comments. Anyway, the Linux kernel
version is sufficient information. Remove these macros to improve readability.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Static variables from dtc.c and pas16.c should not appear in the core
NCR5380.c driver. Aside from being a layering issue this worsens the
divergence between the three core driver variants (atari_NCR5380.c and
sun3_NCR5380.c don't support PSEUDO_DMA) and it can mean multiple hosts
share the same counters.
Fix this by making the pseudo DMA spin counters in the core more generic.
This also avoids the abuse of the {DTC,PAS16}_PUBLIC_RELEASE macros, so
they can be removed.
oak.c doesn't use PDMA and hence it doesn't use the counters and hence it
needs no write_info() method. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the host->info() method is not set, then host->name is used by default.
For atari_scsi, that is exactly the same text. So remove the redundant
info() method. Keep sun3_scsi.c in line with atari_scsi.
Some NCR5380 drivers return an empty string from the info() method
(arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default
(dmx3191d dtc.c g_NCR5380.c pas16.c t128.c).
Implement a common info() method to replace a lot of duplicated code which
the various drivers use to announce the same information.
This replaces most of the (deprecated) show_info() output and all of the
NCR5380_print_info() output. This also eliminates a bunch of code in
g_NCR5380 which just duplicates functionality in the core driver.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The NCR5380_STATS option is only enabled by g_NCR5380 yet it adds
clutter to all three core drivers. The atari_NCR5380.c and sun3_NCR5380.c
core drivers have a slightly different implementation of the
NCR5380_STATS option.
Out of all ten NCR5380 drivers, only one of them (g_NCR5380) actually
has the code to report on the collected stats. Aside from being unreadable,
that code seems to be broken because there's no initialization of timebase.
sun3_NCR5380.c and atari_NCR5380.c have the timebase initialization but
lack the code to report the stats.
Remove all of this code to improve readability and reduce divergence
between the three core drivers.
This patch and the next one completely eliminate the PRINTP and ANDP
pre-processor abuse.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Oak scsi doesn't use any IRQ, but it sets irq = IRQ_NONE rather than
SCSI_IRQ_NONE. Problem is, the core NCR5380 driver expects SCSI_IRQ_NONE
if it is to issue IDENTIFY commands that prevent target disconnection.
And, as Geert points out, IRQ_NONE is part of enum irqreturn.
Other drivers, when they can't get an IRQ or can't use one, will set
host->irq = SCSI_IRQ_NONE (that is, 255). But when they exit they will
attempt to free IRQ 255 which was never requested.
Fix these bugs by using NO_IRQ in place of SCSI_IRQ_NONE and IRQ_NONE.
That means IRQ 0 is no longer probed by ISA drivers but I don't think
this matters.
Setting IRQ = 255 for these ISA drivers is understood to mean no IRQ.
This remains supported so as to avoid breaking existing ISA setups (which
can be difficult to get working) and because existing documentation
(SANE, TLDP etc) describes this usage for the ISA NCR5380 driver options.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
