IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36b3 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this change is to create a data structure for a LAG
as seen by DSA. This is similar to what we have for bridging - we pass a
copy of this structure by value to ->port_lag_join and ->port_lag_leave.
For now we keep the lag_dev, id and a reference count in it. Future
patches will add a list of FDB entries for the LAG (these also need to
be refcounted to work properly).
The LAG structure is created using dsa_port_lag_create() and destroyed
using dsa_port_lag_destroy(), just like we have for bridging.
Because now, the dsa_lag itself is refcounted, we can simplify
dsa_lag_map() and dsa_lag_unmap(). These functions need to keep a LAG in
the dst->lags array only as long as at least one port uses it. The
refcounting logic inside those functions can be removed now - they are
called only when we should perform the operation.
dsa_lag_dev() is renamed to dsa_lag_by_id() and now returns the dsa_lag
structure instead of the lag_dev net_device.
dsa_lag_foreach_port() now takes the dsa_lag structure as argument.
dst->lags holds an array of dsa_lag structures.
dsa_lag_map() now also saves the dsa_lag->id value, so that linear
walking of dst->lags in drivers using dsa_lag_id() is no longer
necessary. They can just look at lag.id.
dsa_port_lag_id_get() is a helper, similar to dsa_port_bridge_num_get(),
which can be used by drivers to get the LAG ID assigned by DSA to a
given port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the intent of the code more clear by using the dedicated helper for
iterating over the ports of a switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DSA LAG API will be changed to become more similar with the bridge
data structures, where struct dsa_bridge holds an unsigned int num,
which is generated by DSA and is one-based. We have a similar thing
going with the DSA LAG, except that isn't stored anywhere, it is
calculated dynamically by dsa_lag_id() by iterating through dst->lags.
The idea of encoding an invalid (or not requested) LAG ID as zero for
the purpose of simplifying checks in drivers means that the LAG IDs
passed by DSA to drivers need to be one-based too. So back-and-forth
conversion is needed when indexing the dst->lags array, as well as in
drivers which assume a zero-based index.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of converting struct net_device *dp->lag_dev into a
struct dsa_lag *dp->lag, we need to rename, for consistency purposes,
all occurrences of the "lag" variable in mv88e6xxx to "lag_dev".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Supporting bridge ports in locked mode using the drop on lock
feature in Marvell mv88e6xxx switchcores is described in the
'88E6096/88E6097/88E6097F Datasheet', sections 4.4.6, 4.4.7 and
5.1.2.1 (Drop on Lock).
This feature is implemented here facilitated by the locked port flag.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These chips have 8 built-in FE PHYs and 3 SERDES interfaces that can
run at 1G. With the blamed commit, the built-in PHYs could no longer
be connected to, using an MII PHY interface mode.
Create a separate .phylink_get_caps callback for these chips, which
takes the FE/GE split into consideration.
Fixes: 2ee84cfefb1e ("net: dsa: mv88e6xxx: convert to phylink_generic_validate()")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220213185154.3262207-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f8701 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352, mv88e6240 and mv88e6176 have a serdes interface. This patch
allows to configure the output swing to a desired value in the
phy-handle of the port. The value which is peak to peak has to be
specified in microvolts. As the chips only supports eight dedicated
values we return EINVAL if the value in the DTS does not match one of
these values.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893b2 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call mv88e6xxx_reg_unlock(chip) before returning on this error path.
Fixes: 7af4a361a62f ("net: dsa: mv88e6xxx: Improve isolation of standalone ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The <= ARRAY_SIZE() needs to be < ARRAY_SIZE() to prevent an out of
bounds error.
Fixes: d4ebf12bcec4 ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to report serdes statistics currently depends on
the cached C_Mode value for the port, read at probe time or updated by
configuration. However, port 4 can be in "automedia" mode when it is
used as a serdes port, meaning it switches between the internal PHY and
the serdes, changing the read-only C_Mode value depending on which
first gains link. Consequently, the C_Mode value read at probe does not
accurately reflect whether the port has the serdes associated with it.
In "net: dsa: mv88e6xxx: add mv88e6352_g2_scratch_port_has_serdes()",
we added a way to read the hardware configuration to determine which
port has the serdes associated with it. Use this to determine which
port reports the serdes statistics.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the mv88e6xxx chip drivers are supplying the supported
interfaces and MAC capabilities, switch the driver to use the generic
phylink validation implementation by removing our own validation
implementations. This causes DSA to call phylink_generic_validate()
on our behalf.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the
Marvell MV88E6xxx DSA switches in preparation to using these for the
validation functionality.
Patch co-authored by Marek.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org> [ fixed 6341 and 6393x ]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the hardware configuration to determine which port is attached
to the serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VTU entry with policy enabled is used in combination with a port's
VTU policy setting to override normal switching behavior for frames
assigned to the entry's VID.
A typical example is to Treat all frames in a particular VLAN as
control traffic, and trap them to the CPU. In which case the relevant
user port's VTU policy would be set to TRAP.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, both the read and write callback would start out
by asserting that the chip's busy flag was cleared. However, both
callbacks also made sure to wait for the clearing of the busy bit
before returning - making the initial check superfluous. The only
time that would ever have an effect was if the busy bit was initially
set for some reason.
With that in mind, make sure to perform an initial check of the busy
bit, after which both read and write can rely the previous operation
to have waited for the bit to clear.
This cuts the number of operations on the underlying MDIO bus by 25%
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a long delay when a busy bit is still set and has to be polled
again.
Measurements on a system with 2 Opals (6097F) and one Agate (6352)
show that even with this much tighter loop, we have about a 50% chance
of the bit being cleared on the first poll, all other accesses see the
bit being cleared on the second poll.
On a standard MDIO bus running MDC at 2.5MHz, a single access with 32
bits of preamble plus 32 bits of data takes 64*(1/2.5MHz) = 25.6us.
This means that mv88e6xxx_smi_direct_wait took 26us + CPU overhead in
the fast scenario, but 26us + 1500us + 26us + CPU overhead in the slow
case - bringing the average close to 1ms.
With this change in place, the slow case is closer to 2*26us + CPU
overhead, with the average well below 100us - a 10x improvement.
This translates to real-world winnings. On a 3-chip 20-port system,
the modprobe time drops by 88%:
Before:
root@coronet:~# time modprobe mv88e6xxx
real 0m 15.99s
user 0m 0.00s
sys 0m 1.52s
After:
root@coronet:~# time modprobe mv88e6xxx
real 0m 2.21s
user 0m 0.00s
sys 0m 1.54s
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c7bd3 ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings
in mac_config") removed forcing of speed and duplex from
mv88e6xxx_mac_config(), where the link is forced down, and left it only
in mv88e6xxx_mac_link_up(), by which time link is unforced.
It seems that (at least on 88E6190) when changing cmode to 2500base-x,
if the link is not forced down, but the speed or duplex are still
forced, the forcing of new settings for speed & duplex doesn't take in
mv88e6xxx_mac_link_up().
Fix this by unforcing speed & duplex in mv88e6xxx_mac_link_down().
Fixes: 64d47d50be7a ("net: dsa: mv88e6xxx: configure interface settings in mac_config")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical mv88e6xxx switch tree like this:
CPU
| .----.
.--0--. | .--0--.
| sw0 | | | sw1 |
'-1-2-' | '-1-2-'
'---'
If sw1p{1,2} are added to a bridge that sw0p1 is not a part of, sw0
still needs to add a crosschip PVT entry for the virtual DSA device
assigned to represent the bridge.
Fixes: ce5df6894a57 ("net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f7f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Added default case to handle undefined cmode scenario in
mv88e6393x_serdes_power() and mv88e6393x_serdes_power() methods.
Addresses-Coverity: 1494644 ("Uninitialized scalar variable")
Fixes: 21635d9203e1c (net: dsa: mv88e6xxx: Fix application of erratum 4.8 for 88E6393X)
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211209041552.9810-1-amhamza.mgc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes a misunderstanding in commit 4a3e0aeddf09 ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7ac (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf09
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf09 ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't really need new switch API for these, and with new switches
which intend to add support for this feature, it will become cumbersome
to maintain.
The change consists in restructuring the two drivers that implement this
offload (sja1105 and mv88e6xxx) such that the offload is enabled and
disabled from the ->port_bridge_{join,leave} methods instead of the old
->port_bridge_tx_fwd_{,un}offload.
The only non-trivial change is that mv88e6xxx_map_virtual_bridge_to_pvt()
has been moved to avoid a forward declaration, and the
mv88e6xxx_reg_lock() calls from inside it have been removed, since
locking is now done from mv88e6xxx_port_bridge_{join,leave}.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
