IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98ca ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
./drivers/net/can/bxcan.c:970:2-9: line 970 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:964:2-9: line 964 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:958:2-9: line 958 is redundant because platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4878
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230506080725.68401-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the basic extended CAN controller (bxCAN) found in many
low- to middle-end STM32 SoCs. It supports the Basic Extended CAN
protocol versions 2.0A and B with a maximum bit rate of 1 Mbit/s.
The controller supports two channels (CAN1 as primary and CAN2 as
secondary) and the driver can enable either or both of the channels. They
share some of the required logic (e. g. clocks and filters), and that means
you cannot use the secondary CAN without enabling some hardware resources
managed by the primary CAN.
Each channel has 3 transmit mailboxes, 2 receive FIFOs with 3 stages and
28 scalable filter banks.
It also manages 4 dedicated interrupt vectors:
- transmit interrupt
- FIFO 0 receive interrupt
- FIFO 1 receive interrupt
- status change error interrupt
Driver uses all 3 available mailboxes for transmission and FIFO 0 for
reception. Rx filter rules are configured to the minimum. They accept
all messages and assign filter 0 to CAN1 and filter 14 to CAN2 in
identifier mask mode with 32 bits width. It enables and uses transmit,
receive buffers for FIFO 0 and error and status change interrupts.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230328073328.3949796-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
