IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
On some EHCI debug controllers after the host controller driver is
activated, the debug controller will occasionally fail to submit a
bulk write URB. On controllers that exhibit this behavior a dummy
bulk write must get submitted to resynchronize the device.
The "dummy bulk write" does not get received by the host attached to
the other end of the usb debug device. The usb debug device simply
acknowledges the "dummy bulk write" and returns to a usable state.
The behavior, without this patch is that you see missing text from a
complete kernel boot when using the keep option to the earlyprintk
kernel argument.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some EHCI usb debug controllers, the EHCI debug device will fail to
be seen after a port reset, after a warm reset. Two options exist to
get the device to initialize correctly.
Option 1 is to unplug and plug in the device.
Option 2 is to use the EHCI port test to get the usb debug device to
start talking again. At that point the debug controller port reset
will succeed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
CC: dbrownell@users.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements several changes:
1) Improve the capability to debug the dbgp driver
The dbgp_ehci_status() was added in a number of places to report
the critical ehci registers to diagnose the cause of a failure of
the ehci-dbgp driver.
2) Capability to survive the host controller initialization
The dbgp_external_startup(), dbgp_not_safe, and dbgp_phys_port were
added so as to allow the ehci-dbgp to re-initialize after the ehci
host controller is reset by the standard host controller driver.
This same routine is common for the early startup or
re-initialization.
This resulted in the need to move some of the initialization code
out of the __init section because the ehci driver has the
possibility to be loaded later on as a kernel module.
3) Stability improvements for device initialization
The device enumeration from 0 to 127 has the possibility to fail
the first time after a warm reset on some older EHCI debug
controllers. The enumeration will be tried up to 3 times to
account for this failure case.
The dbg_wait_until_complete() was changed to wait up to 250 ms
before failing which only comes into play during device
initialization. The maximum delay will never get hit during the
course of normal operation of the driver, unless the device got
unplugged or there was a ehci controller failure, in which case the
dbgp device driver will shut itself down.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the EHCI host controller as a polled device, a bit more
tolerance is required in terms of delays. On some 3+ghz systems the
cpu loops were faster than the EHCI device mmio and resulted in the
controller failing to initialize.
On at least one first generation EHCI controller when it was not
operating in interrupt mode, it would fail to report a port change
status, but executing the port reset allowed the debug controller to
work correctly anyway. This errata causes a one time 300ms delay in
the boot time, where as the typical delay is 1-5ms for an EHCI
controller that does not have this errata.
The debug printk's were fixed to have the correct state messages, and
there was a conversion from using early_printk to printk to avoid
calling the dbgp driver while debugging the initialization.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI quirk code executes a BIOS hand off to obtain full control of
the EHCI host controller, the self contained ehci-dbgp driver must do
the same thing using the early PCI API, else the BIOS can cause a
fatal fault.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: dbrownell@users.sourceforge.net
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rs232 drivers send a carriage return prior to a new line in the
early printk code.
The usb debug driver should do the same because you want to be able to
use the same terminal programs and tools for analysis of early printk
data.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the dbgp early printk driver in advance of refactoring and adding
new code, so the changes to this code are tracked separately from the
move of the code.
The drivers/usb/early directory will be the location of the current
and future early usb code for driving usb devices prior initializing
the standard interrupt driven USB drivers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
