IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Daniel discovered recently I broke TC filter replace (and fixed
it in commit ad9294dbc227 ("bpf: fix cls_bpf on filter replace")).
Add a test to make sure it never happens again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.
Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.
The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:
$ tc filter add dev foo ingress bpf obj sample_ret0.o \
sec .text verbose skip_sw
Prog section '.text' loaded (5)!
- Type: 3
- Instructions: 2 (0 over limit)
- License:
Verifier analysis:
0: (b7) r0 = 0
1: (95) exit
[netdevsim] Hello from netdevsim!
processed 2 insns, stack depth 0
"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not compile netdevsim/bpf.c if BPF syscall is not
enabled. Otherwise bpf core would have to provide wrappers
for all functions offload drivers may call, even though
system will never see a BPF object.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.
iproute2 may be built without libmnl support, in which case the extack
messages will not be reported. Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to i40e and i40evf only.
Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.
Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.
Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts. This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.
Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.
Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.
Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed. Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.
Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.
Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
with the introduction of commit
b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 513674b5a2c9 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes: 513674b5a2c9 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: remove spinlock from 'csum' action
Similarly to what has been done earlier with other actions [1][2], this
series tries to improve the performance of 'csum' tc action, removing a
spinlock in the data path. Patch 1 lets act_csum use per-CPU counters;
patch 2 removes spin_{,un}lock_bh() calls from the act() method.
test procedure (using pktgen from https://github.com/netoptimizer):
# ip link add name eth1 type dummy
# ip link set dev eth1 up
# tc qdisc add dev eth1 root handle 1: prio
# for a in pass drop; do
> tc filter del dev eth1 parent 1: pref 10 matchall action csum udp
> tc filter add dev eth1 parent 1: pref 10 matchall action csum udp $a
> for n in 2 4; do
> ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $n -n 1000000 -i eth1
> done
> done
test results:
| | before patch | after patch
$a | $n | avg. pps/thread | avg. pps/thread
-----+----+-----------------+----------------
pass | 2 | 1671463 ± 4% | 1920789 ± 3%
pass | 4 | 648797 ± 1% | 738190 ± 1%
drop | 2 | 3212692 ± 2% | 3719811 ± 2%
drop | 4 | 1078824 ± 1% | 1328099 ± 1%
references:
[1] https://www.spinics.net/lists/netdev/msg334760.html
[2] https://www.spinics.net/lists/netdev/msg465862.html
v3 changes:
- use rtnl_dereference() in place of rcu_dereference() in tcf_csum_dump()
v2 changes:
- add 'drop' test, it produces more contentions
- use RCU-protected struct to store 'action' and 'update_flags', to avoid
reading the values from subsequent configurations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use RCU instead of spin_{,unlock}_bh() to protect concurrent read/write on
act_csum configuration, to reduce the effects of contention in the data
path when multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS: 00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes: f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It takes 1sec for bond link down notification to hit user-space
when all slaves of the bond go down. 1sec is too long for
protocol daemons in user-space relying on bond notification
to recover (eg: multichassis lag implementations in user-space).
Since the link event code already marks team device port link events
as urgent, this patch moves the code to cover all lag ports and master.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to ixgbe only.
Shannon Nelson provides an implementation of the ipsec hardware offload
feature for the ixgbe driver for these devices: x540, x550, 82599.
The ixgbe NICs support ipsec offload for 1024 Rx and 1024 Tx Security
Associations (SAs), using up to 128 inbound IP addresses, and using the
rfc4106(gcm(aes)) encryption. This code does not yet support checksum
offload, or TSO in conjunction with the ipsec offload - those will be
added in the future.
This code shows improvements in both packet throughput and CPU utilization.
For example, here are some quicky numbers that show the magnitude of the
performance gain on a single run of "iperf -c <dest>" with the ipsec
offload on both ends of a point-to-point connection:
9.4 Gbps - normal case
7.6 Gbps - ipsec with offload
343 Mbps - ipsec no offload
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Reichel says:
====================
GEHC Bx50 Switch Support
This adds support for the internal switch found in GE Healthcare
B450v3, B650v3 and B850v3. All devices use a GPIO bitbanged MDIO
bus to communicate with the switch and a PCIe based network card
for exchanging network data. The cpu network data link requires,
that the switch's internal phy interface is enabled, so support
for that is added by the first patch in this series.
The patch series is based on v4.15-rc8.
Changes since PATCHv4:
* Introduce dsa_port_link_(un)register_of and mark the fixed
variant static.
* Update patch description to describe the phy<->phy connection
from i210 to the Marvell switch
Changes since PATCHv3:
* Enable the phy in dsa_port_setup() instead of abusing the
fixed link setup function
Changes since PATCHv2:
* Add phy nodes to switch in bx50.dtsi and reference them
from switch ports
* Enable cpu-port's phy based on 'phy-handle' instead of 'phy-mode'
Changes since PATCHv1:
* Use 'marvell,mv88e6085' instead of introducing compatible
string for mv88e6240.
* Fix indention of DT nodes
* Only enable 'cpu' phy, if explicitly set to "internal".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0 Intel Corporation I210 Gigabit Network Connection
+-02.0-[04]----00.0 Intel Corporation I210 Gigabit Network Connection
\-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3, B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of ORC unwinder and FRAME POINTER unwinder, the stack
trace skipping requirements have changed.
I went through the tracing stack trace dumps with ORC and with frame
pointers and recalculated the proper values.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The function tracer can create a dynamically allocated trampoline that is
called by the function mcount or fentry hook that is used to call the
function callback that is registered. The problem is that the orc undwinder
will bail if it encounters one of these trampolines. This breaks the stack
trace of function callbacks, which include the stack tracer and setting the
stack trace for individual functions.
Since these dynamic trampolines are basically copies of the static ftrace
trampolines defined in ftrace_*.S, we do not need to create new orc entries
for the dynamic trampolines. Finding the return address on the stack will be
identical as the functions that were copied to create the dynamic
trampolines. When encountering a ftrace dynamic trampoline, we can just use
the orc entry of the ftrace static function that was copied for that
trampoline.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaZ5GHAAoJEFmIoMA60/r8UmAP/AjrS+C+OSMHzM/U/h+UHmou
DRg5Tg7gG3PjnnKULEQno4BSGM5VJeXpM+QC8Ypqa2I1T4GTHVHiSn6qtOi4yn0R
k9CAGyeRD1zYH4Mtw4dyUOVE5j0ANoBuji0KklawqaxcPFJDh6FhSCbChPq0WjIA
ZarpJZ4YKeJF5ZYXFs4G5W6EjnXokYogjZL3lzCOVXoTC9aVfo+NoJ9Hg9P38VA3
WmYaLUEbIzV40JXkDieZq7nqO8m3mFBtxi7+74BvsjtgozW0og1tPNI6Hige6/U3
dUAzrdNGQg52T3pTMm8r0+efagDV11UO0IBhVhktNzTTVaUggxluBEza//FaQ85m
PLm7vsnwtIALujnp74VcFnTsVM2yYa9NeaPNIQ9FQ6kOB7TS0/ELtyHaPLNS8JoM
lhssdhT3jmVNg86UG2pOi9MJZhyYb6SQmWAGmYopzwEn/idBTOcLsTdcbptF5LfP
0hbc9BLI0wCF8sv0JXD4IBQFWN264z1vPGNDWD4cnkEMPiAJ23h1ySpS3S0HjZe3
c6AMEMNj5E1b6unwIebBHfeSj4DUUnfyypb4/oICNxCThQBIzPyXtnlk07DNFMOl
9pRZBebfUl5xAZeWz2Sxxvs0PqMc8QEDa5j8YzLS3cgz9y1i80Hn6fGxSeHptgC+
Zb4SYRr5S82kU3SbAtnY
=tRVW
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix AMD regression due to not re-enabling the big window on resume
(Christian König)"
* tag 'pci-v4.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
x86/PCI: Enable AMD 64-bit window on resume
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Rostedt discovered that the ftrace stack tracer is broken when
it's used with the ORC unwinder. The problem is that objtool is
instructed by the Makefile to ignore the ftrace_64.S code, so it doesn't
generate any ORC data for it.
Fix it by making the asm code objtool-friendly:
- Objtool doesn't like the fact that save_mcount_regs pushes RBP at the
beginning, but it's never restored (directly, at least). So just skip
the original RBP push, which is only needed for frame pointers anyway.
- Annotate some functions as normal callable functions with
ENTRY/ENDPROC.
- Add an empty unwind hint to return_to_handler(). The return address
isn't on the stack, so there's nothing ORC can do there. It will just
punt in the unlikely case it tries to unwind from that code.
With all that fixed, remove the OBJECT_FILES_NON_STANDARD Makefile
annotation so objtool can read the file.
Link: http://lkml.kernel.org/r/20180123040746.ih4ep3tk4pbjvg7c@treble
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info. Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a chip reset most of the table contents are lost, so must be
restored. This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware. We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.
The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle. However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add in the code for running and stopping the hardware ipsec
encryption/decryption engine. It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Fix divide by zero in mlx5, from Talut Batheesh.
2) Guard against invalid GSO packets coming from untrusted guests and
arriving in qdisc_pkt_len_init(), from Eric Dumazet.
3) Similarly add such protection to the various protocol GSO handlers.
From Willem de Bruijn.
4) Fix regression added to IGMP source address checking for IGMPv3
reports, from Felix Feitkau.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tls: Correct length of scatterlist in tls_sw_sendpage
be2net: restore properly promisc mode after queues reconfiguration
net: igmp: fix source address check for IGMPv3 reports
gso: validate gso_type in GSO handlers
net: qdisc_pkt_len_init() should be more robust
ibmvnic: Allocate and request vpd in init_resources
ibmvnic: Revert to previous mtu when unsupported value requested
ibmvnic: Modify buffer size and number of queues on failover
rds: tcp: compute m_ack_seq as offset from ->write_seq
usbnet: silence an unnecessary warning
cxgb4: fix endianness for vlan value in cxgb4_tc_flower
cxgb4: set filter type to 1 for ETH_P_IPV6
net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare
Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.
A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.
Note that this issue doesn't affect net.git yet.
Fixes: 97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.
Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
