IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sdhi hardware, so that polling needs to be used
with tmio_mmc and card detection is handled in the platform code.
This patch allows to set tmio_mmc capabilities (to pass the
MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq and provide seperated file for interrupts support.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.
Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some modules already need to talk to at least PROTECT_KEY
register, while at that, add defines to the entire register
space.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixed warnings about unprototyped global functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Fix build break on symbol-prefixed archs
initramfs: fix initramfs size calculation
initramfs: generalize initramfs_data.xxx.S variants
scripts/kallsyms: Enable error messages while hush up unnecessary warnings
scripts/setlocalversion: update comment
kbuild: Use a single clean rule for kernel and external modules
kbuild: Do not run make clean in $(srctree)
scripts/mod/modpost.c: fix commentary accordingly to last changes
kbuild: Really don't clean bounds.h and asm-offsets.h
Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.
It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reorder struct fsnotfiy_mark to remove 8 bytes of alignment padding on 64
bit builds. Shrinks fsnotfiy_mark to 128 bytes allowing more objects per
slab in its kmem_cache and reduces the number of cachelines needed for
each structure.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
The comments for FAN_CLOSE_WRITE and FAN_CLOSE_NOWRITE do not match
FS_CLOSE_WRITE and FS_CLOSE_NOWRITE, respectively. WRITE is for
writable files while NOWRITE is for non-writable files.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify has a very limited number of events it sends on directories. The
usefulness of these events is yet to be seen and still we send them. This
is particularly painful for mount marks where one might receive many of
these useless events. As such this patch will drop events on IS_DIR()
inodes unless they were explictly requested with FAN_ON_DIR.
This means that a mark on a directory without FAN_EVENT_ON_CHILD or
FAN_ON_DIR is meaningless and will result in no events ever (although it
will still be allowed since detecting it is hard)
Signed-off-by: Eric Paris <eparis@redhat.com>
The _IN_ in the naming is reserved for flags only used by inotify. Since I
am about to use this flag for fanotify rename it to be generic like the
rest.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify currently has no limit on the number of listeners a given user can
have open. This patch limits the total number of listeners per user to
128. This is the same as the inotify default limit.
Signed-off-by: Eric Paris <eparis@redhat.com>
Some fanotify groups, especially those like AV scanners, will need to place
lots of marks, particularly ignore marks. Since ignore marks do not pin
inodes in cache and are cleared if the inode is removed from core (usually
under memory pressure) we expose an interface for listeners, with
CAP_SYS_ADMIN, to override the maximum number of marks and be allowed to
set and 'unlimited' number of marks. Programs which make use of this
feature will be able to OOM a machine.
Signed-off-by: Eric Paris <eparis@redhat.com>
There is currently no limit on the number of marks a given fanotify group
can have. Since fanotify is gated on CAP_SYS_ADMIN this was not seen as
a serious DoS threat. This patch implements a default of 8192, the same as
inotify to work towards removing the CAP_SYS_ADMIN gating and eliminating
the default DoS'able status.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify has a defualt max queue depth. This patch allows processes which
explicitly request it to have an 'unlimited' queue depth. These processes
need to be very careful to make sure they cannot fall far enough behind
that they OOM the box. Thus this flag is gated on CAP_SYS_ADMIN.
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently fanotify has no maximum queue depth. Since fanotify is
CAP_SYS_ADMIN only this does not pose a normal user DoS issue, but it
certianly is possible that an fanotify listener which can't keep up could
OOM the box. This patch implements a default 16k depth. This is the same
default depth used by inotify, but given fanotify's better queue merging in
many situations this queue will contain many additional useful events by
comparison.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify is supposed to be able to flush all marks. This is mostly useful
for the AV community to flush all cached decisions on a security policy
change. This functionality has existed in the kernel but wasn't correctly
exposed to userspace.
Signed-off-by: Eric Paris <eparis@redhat.com>
fsnotify perm events do not call fsnotify parent. That means you cannot
register a perm event on a directory and enforce permissions on all inodes in
that directory. This patch fixes that situation.
Signed-off-by: Eric Paris <eparis@redhat.com>
When fsnotify groups return errors they are ignored. For permissions
events these should be passed back up the stack, but for most events these
should continue to be ignored.
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently the userspace struct exposed by fanotify uses
__attribute__((packed)) to make sure that alignment works on multiarch
platforms. Since this causes a severe performance penalty on some
platforms we are going to switch to using explicit alignment notation on
the 64bit values so we don't have to use 'packed'
Signed-off-by: Eric Paris <eparis@redhat.com>
The fanotify listeners needs to be able to specify what types of operations
they are going to perform so they can be ordered appropriately between other
listeners doing other types of operations. They need this to be able to make
sure that things like hierarchichal storage managers will get access to inodes
before processes which need the data. This patch defines 3 possible uses
which groups must indicate in the fanotify_init() flags.
FAN_CLASS_PRE_CONTENT
FAN_CLASS_CONTENT
FAN_CLASS_NOTIF
Groups will receive notification in that order. The order between 2 groups in
the same class is undeterministic.
FAN_CLASS_PRE_CONTENT is intended to be used by listeners which need access to
the inode before they are certain that the inode contains it's final data. A
hierarchical storage manager should choose to use this class.
FAN_CLASS_CONTENT is intended to be used by listeners which need access to the
inode after it contains its intended contents. This would be the appropriate
level for an AV solution or document control system.
FAN_CLASS_NOTIF is intended for normal async notification about access, much the
same as inotify and dnotify. Syncronous permissions events are not permitted
at this class.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify needs to be able to specify that some groups get events before
others. They use this idea to make sure that a hierarchical storage
manager gets access to files before programs which actually use them. This
is purely infrastructure. Everything will have a priority of 0, but the
infrastructure will exist for it to be non-zero.
Signed-off-by: Eric Paris <eparis@redhat.com>
We disabled the ability to build fanotify in commit 7c5347733d.
This reverts that commit and allows people to build fanotify.
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
This helps protect us from overflow issues down in the
individual protocol sendmsg/recvmsg handlers. Once
we hit INT_MAX we truncate out the rest of the iovec
by setting the iov_len members to zero.
This works because:
1) For SOCK_STREAM and SOCK_SEQPACKET sockets, partial
writes are allowed and the application will just continue
with another write to send the rest of the data.
2) For datagram oriented sockets, where there must be a
one-to-one correspondance between write() calls and
packets on the wire, INT_MAX is going to be far larger
than the packet size limit the protocol is going to
check for and signal with -EMSGSIZE.
Based upon a patch by Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we stop a namespace we flush the table and free one, but the
added fn_zone-s (and their hashes if grown) are leaked. Need to free.
Tries releases all its stuff in the flushing code.
Shame on us - this bug exists since the very first make-fib-per-net
patches in 2.6.27 :(
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the packet dequeuing interface of dccp_write_xmit() to allow
1. CCIDs to take care of timing when the next packet may be sent;
2. delayed sending (as before, with an inter-packet gap up to 65.535 seconds).
The main purpose is to take CCID-2 out of its polling mode (when it is network-
limited, it tries every millisecond to send, without interruption).
The mode of operation for (2) is as follows:
* new packet is enqueued via dccp_sendmsg() => dccp_write_xmit(),
* ccid_hc_tx_send_packet() detects that it may not send (e.g. window full),
* it signals this condition via `CCID_PACKET_WILL_DEQUEUE_LATER',
* dccp_write_xmit() returns without further action;
* after some time the wait-condition for CCID becomes true,
* that CCID schedules the tasklet,
* tasklet function calls ccid_hc_tx_send_packet() via dccp_write_xmit(),
* since the wait-condition is now true, ccid_hc_tx_packet() returns "send now",
* packet is sent, and possibly more (since dccp_write_xmit() loops).
Code reuse: the taskled function calls dccp_write_xmit(), the timer function
reduces to a wrapper around the same code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: (28 commits)
net/9p: Return error on read with NULL buffer
9p: Add datasync to client side TFSYNC/RFSYNC for dotl
net/9p: Return error if we fail to encode protocol data
fs/9p: Use generic_file_open with lookup_instantiate_filp
fs/9p: Add missing iput in v9fs_vfs_lookup
fs/9p: Use mknod 9p operation on create without open request
net/9p: Add waitq to VirtIO transport.
[net/9p]Serialize virtqueue operations to make VirtIO transport SMP safe.
9p: Implement TREADLINK operation for 9p2000.L
9p: Use V9FS_MAGIC in statfs
9p: Implement TGETLOCK
9p: Implement TLOCK
[9p] Introduce client side TFSYNC/RFSYNC for dotl.
[fs/9p] Add file_operations for cached mode in dotl protocol.
fs/9p: Add access = client option to opt in acl evaluation.
fs/9p: Implement create time inheritance
fs/9p: Update ACL on chmod
fs/9p: Implement setting posix acl
fs/9p: Add xattr callbacks for POSIX ACL
fs/9p: Implement POSIX ACL permission checking function
...
Today's git tree fails to build on !CONFIG_BLOCK, due to upstream commit
367a51a339 ("fs: Add FITRIM ioctl"):
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
The commit adds uint64_t type usage to fs.h, but linux/types.h is not included
explicitly - it's only included implicitly via linux/blk_types.h, and there only if
CONFIG_BLOCK is enabled.
Add the explicit #include to fix this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SYNOPSIS
size[4] Tfsync tag[2] fid[4] datasync[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
If datasync flag is specified data will be fleshed but does not flush
modified metadata unless that metadata is needed in order to allow a
subsequent data retrieval to be correctly handled.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TReadlink tag[2] fid[4]
size[4] RReadlink tag[2] target[s]
Description
Readlink is used to return the contents of the symoblic link
referred by fid. Contents of symboic link is returned as a
response.
target[s] - Contents of the symbolic link referred by fid.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Use V9FS_MAGIC as the file system type while filling kernel statfs
strucutre instead of using host file system magic number. Also move
the definition of V9FS_MAGIC from v9fs.h to standard magic.h file.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TGetlock tag[2] fid[4] getlock[n]
size[4] RGetlock tag[2] getlock[n]
Description
TGetlock is used to test for the existence of byte range posix locks on a file
identified by given fid. The reply contains getlock structure. If the lock could
be placed it returns F_UNLCK in type field of getlock structure. Otherwise it
returns the details of the conflicting locks in the getlock structure
getlock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK
start[8] - Starting offset for lock
length[8] - Number of bytes to check for the lock
If length is 0, check for lock in all bytes starting at the location
'start' through to the end of file
pid[4] - PID of the process that wants to take lock/owns the task
in case of reply
client[4] - Client id of the system that owns the process which
has the conflicting lock
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TLock tag[2] fid[4] flock[n]
size[4] RLock tag[2] status[1]
Description
Tlock is used to acquire/release byte range posix locks on a file
identified by given fid. The reply contains status of the lock request
flock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK, F_UNLCK
flags[4] - Flags could be either of
P9_LOCK_FLAGS_BLOCK - Blocked lock request, if there is a
conflicting lock exists, wait for that lock to be released.
P9_LOCK_FLAGS_RECLAIM - Reclaim lock request, used when client is
trying to reclaim a lock after a server restrart (due to crash)
start[8] - Starting offset for lock
length[8] - Number of bytes to lock
If length is 0, lock all bytes starting at the location 'start'
through to the end of file
pid[4] - PID of the process that wants to take lock
client_id[4] - Unique client id
status[1] - Status of the lock request, can be
P9_LOCK_SUCCESS(0), P9_LOCK_BLOCKED(1), P9_LOCK_ERROR(2) or
P9_LOCK_GRACE(3)
P9_LOCK_SUCCESS - Request was successful
P9_LOCK_BLOCKED - A conflicting lock is held by another process
P9_LOCK_ERROR - Error while processing the lock request
P9_LOCK_GRACE - Server is in grace period, it can't accept new lock
requests in this period (except locks with
P9_LOCK_FLAGS_RECLAIM flag set)
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
SYNOPSIS
size[4] Tfsync tag[2] fid[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
register_kprobe() downs the 'text_mutex' and then calls
jump_label_text_reserved(), which downs the 'jump_label_mutex'.
However, the jump label code takes those mutexes in the reverse
order.
Fix by requiring the caller of jump_label_text_reserved() to do
the jump label locking via the newly added: jump_label_lock(),
jump_label_unlock(). Currently, kprobes is the only user
of jump_label_text_reserved().
Reported-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
LKML-Reference: <759032c48d5e30c27f0bba003d09bffa8e9f28bb.1285965957.git.jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Now that the node ID is tracked in the irq_data structure, update the
irq_node() definition accordingly. This fixes up irq_node() usage under
GENERIC_HARDIRQS_NO_DEPRECATED && SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
LKML-Reference: <20101028023031.GB10365@linux-sh.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unfortunately perf can't deal with anything other than direct structure
accesses in the TP_printk() section. It will drop dead when it sees
jbd2_dev_to_name() in the "print fmt" section of the tracepoint.
Addresses-Google-Bug: 3138508
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300: (44 commits)
MN10300: Save frame pointer in thread_info struct rather than global var
MN10300: Change "Matsushita" to "Panasonic".
MN10300: Create a defconfig for the ASB2364 board
MN10300: Update the ASB2303 defconfig
MN10300: ASB2364: Add support for SMSC911X and SMC911X
MN10300: ASB2364: Handle the IRQ multiplexer in the FPGA
MN10300: Generic time support
MN10300: Specify an ELF HWCAP flag for MN10300 Atomic Operations Unit support
MN10300: Map userspace atomic op regs as a vmalloc page
MN10300: And Panasonic AM34 subarch and implement SMP
MN10300: Delete idle_timestamp from irq_cpustat_t
MN10300: Make various interrupt priority settings configurable
MN10300: Optimise do_csum()
MN10300: Implement atomic ops using atomic ops unit
MN10300: Make the FPU operate in non-lazy mode under SMP
MN10300: SMP TLB flushing
MN10300: Use the [ID]PTEL2 registers rather than [ID]PTEL for TLB control
MN10300: Make the use of PIDR to mark TLB entries controllable
MN10300: Rename __flush_tlb*() to local_flush_tlb*()
MN10300: AM34 erratum requires MMUCTR read and write on exception entry
...
* akpm-incoming-2: (139 commits)
epoll: make epoll_wait() use the hrtimer range feature
select: rename estimate_accuracy() to select_estimate_accuracy()
Remove duplicate includes from many files
ramoops: use the platform data structure instead of module params
kernel/resource.c: handle reinsertion of an already-inserted resource
kfifo: fix kfifo_alloc() to return a signed int value
w1: don't allow arbitrary users to remove w1 devices
alpha: remove dma64_addr_t usage
mips: remove dma64_addr_t usage
sparc: remove dma64_addr_t usage
fuse: use release_pages()
taskstats: use real microsecond granularity for CPU times
taskstats: split fill_pid function
taskstats: separate taskstats commands
delayacct: align to 8 byte boundary on 64-bit systems
delay-accounting: reimplement -c for getdelays.c to report information on a target command
namespaces Kconfig: move namespace menu location after the cgroup
namespaces Kconfig: remove the cgroup device whitelist experimental tag
namespaces Kconfig: remove pointless cgroup dependency
namespaces Kconfig: make namespace a submenu
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: Remove the multi-page alignment facility
x86-32: Allocate irq stacks seperate from percpu area
x86-32, mm: Remove duplicated #include
x86, printk: Get rid of <0> from stack output
x86, kexec: Make sure to stop all CPUs before exiting the kernel
x86/vsmp: Eliminate kconfig dependency warning
Commit 84061e0 fixed an accounting bug only to introduce the
possibility of a kernel OOPS if the journal has a non-zero j_errno
field indicating that the file system had detected a fs inconsistency.
After the journal replay, if the journal superblock indicates that the
file system has an error, this indication is transfered to the file
system and then ext4_commit_super() is called to write this to the
disk.
But since the percpu counters are now initialized after the journal
replay, the call to ext4_commit_super() will cause a kernel oops since
it needs to use the percpu counters the ext4 superblock structure.
The fix is to skip setting the ext4 free block and free inode fields
if the percpu counter has not been set.
Thanks to Ken Sumrall for reporting and analyzing the root causes of
this bug.
Addresses-Google-Bug: #3054080
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This is analogous to Jan Kara's commit,
f446daaea9
mm: implement writeback livelock avoidance using page tagging
but since we forked write_cache_pages, we need to reimplement
it there (and in ext4_da_writepages, since range_cyclic handling
was moved to there)
If you start a large buffered IO to a file, and then set
fsync after it, you'll find that fsync does not complete
until the other IO stops.
If you continue re-dirtying the file (say, putting dd
with conv=notrunc in a loop), when fsync finally completes
(after all IO is done), it reports via tracing that
it has written many more pages than the file contains;
in other words it has synced and re-synced pages in
the file multiple times.
This then leads to problems with our writeback_index
update, since it advances it by pages written, and
essentially sets writeback_index off the end of the
file...
With the following patch, we only sync as much as was
dirty at the time of the sync.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Adds an filesystem independent ioctl to allow implementation of file
system batched discard support. I takes fstrim_range structure as an
argument. fstrim_range is definec in the include/fs.h and its
definition is as follows.
struct fstrim_range {
start;
len;
minlen;
}
start - first Byte to trim
len - number of Bytes to trim from start
minlen - minimum extent length to trim, free extents shorter than this
number of Bytes will be ignored. This will be rounded up to fs
block size.
It is also possible to specify NULL as an argument. In this case the
arguments will set itself as follows:
start = 0;
len = ULLONG_MAX;
minlen = 0;
So it will trim the whole file system at one run.
After the FITRIM is done, the number of actually discarded Bytes is stored
in fstrim_range.len to give the user better insight on how much storage
space has been really released for wear-leveling.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Many tracepoints were populating an ext4_allocation_context
to pass in, but this requires a slab allocation even when
tracepoints are off. In fact, 4 of 5 of these allocations
were only for tracing. In addition, we were only using a
small fraction of the 144 bytes of this structure for this
purpose.
We can do away with all these alloc/frees of the ac and
simply pass in the bits we care about, instead.
I tested this by turning on tracing and running through
xfstests on x86_64. I did not actually do anything with
the trace output, however.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Our QA reported an oops in the ext4_mb_release_group_pa tracing,
and Josef Bacik pointed out that it was because we may have a
non-null but uninitialized ac_inode in the allocation context.
I can reproduce it when running xfstests with ext4 tracepoints on,
on a CONFIG_SLAB_DEBUG kernel.
We call trace_ext4_mb_release_group_pa from 2 places,
ext4_mb_discard_group_preallocations and
ext4_mb_discard_lg_preallocations
In both cases we allocate an ac as a container just for tracing (!)
and never fill in the ac_inode. There's no reason to be assigning,
testing, or printing it as far as I can see, so just remove it from
the tracepoint.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This is done the same way as helper sb_issue_discard for
blkdev_issue_discard.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This fixes a hang seen in jbd2_journal_release_jbd_inode
on a lot of Power 6 systems running with ext4. When we get
in the hung state, all I/O to the disk in question gets blocked
where we stay indefinitely. Looking at the task list, I can see
we are stuck in jbd2_journal_release_jbd_inode waiting on a
wake up. I added some debug code to detect this scenario and
dump additional data if we were stuck in jbd2_journal_release_jbd_inode
for longer than 30 minutes. When it hit, I was able to see that
i_flags was 0, suggesting we missed the wake up.
This patch changes i_flags to be an unsigned long, uses bit operators
to access it, and adds barriers around the accesses. Prior to applying
this patch, we were regularly hitting this hang on numerous systems
in our test environment. After applying the patch, the hangs no longer
occur.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'flock' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
locks: turn lock_flocks into a spinlock
fasync: re-organize fasync entry insertion to allow it under a spinlock
locks/nfsd: allocate file lock outside of spinlock
lockd: fix nlmsvc_notify_blocked locking
lockd: push lock_flocks down
This make epoll use hrtimers for the timeout value which prevents
epoll_wait() from timing out up to a millisecond early.
This mirrors the behavior of select() and poll().
Signed-off-by: Shawn Bohrer <shawn.bohrer@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As each board and system has different memory for ramoops. It's better to
define the platform data instead of module params.
[akpm@linux-foundation.org: fix ramoops_remove() return type]
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new __kfifo_int_must_check_helper() helper function, which is needed
for kfifo_alloc() to return the right signed integer value.
The origin __kfifo_must_check_helper() helper was renamed into
__kfifo_uint_must_check_helper() to show the sign which is expected and
returned.
(And revert the temporary disabling of __kfifo_must_check_helper())
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The taskstats interface uses microsecond granularity for the user and
system time values. The conversion from cputime to the taskstats values
uses the cputime_to_msecs primitive which effectively limits the
granularity to milliseconds. Add the cputime_to_usecs primitive for
architectures that have better, more precise CPU time values. Remove
cputime_to_msecs primitive because there are no more users left.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Luck Tony <tony.luck@intel.com>
Cc: Shailabh Nagar <nagar1234@in.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shailabh Nagar <nagar@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RapidIO spec v.2.1 adds Idle Sequence 2 into LP-Serial Physical Layer.
The fix ensures that corresponding bits are not corrupted during error
handling.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Detects RIO link to the already enumerated device and properly sets links
between device objects. Changes to the enumeration/discovery logic:
1. Use Master Enable bit to signal end of the enumeration - agents may
start their discovery process as soon as they see this bit set
(Component Tag register was used before for this purpose).
2. Enumerator sets Component Tag (!= 0) immediately during device
setup. This allows to identify the device if the redundant route
exists in a RIO system.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the RIO switch driver and definitions for IDT CPS-1848 and CPS-1616
Gen2 devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Change to create attribute "routes" only for switches.
2. Add a switch-specific callback to create/remove proprietary attributes.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default error-stopped state handler provides recovery mechanism as
defined by RIO specification.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create back and forward links between RIO devices. These links are
intended for use by error management and hot-plug extensions. Links for
redundant RIO connections between switches are not set (will be fixed in a
separate patch).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The switch port information is obtained and stored during RIO device
setup. Therefore repeated reads from Switch Port Information CAR may be
removed.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of RapidIO patches extends support for standard error recovery
mechanism and adds new IDT Gen2 sRIO switch devices - CPS-1848 and
CPS-1616. Implementation of the standard error-stopped state recovery
mechanism (as defined by the RapidIO specification) is required for the
new switches.
Version 2 of this set of patches addresses received comments and fixes an
error notification setup issue found in the idt_gen2.c after the first
version was released.
This patch:
Make RapidIO devices appear in /sys/devices/rapidio directory instead of
top of /sys/devices directory.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for extended byte synchronous mode feature of hardware.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In /proc/stat, the number of per-IRQ event is shown by making a sum each
irq's events on all cpus. But we can make use of kstat_irqs().
kstat_irqs() do the same calculation, If !CONFIG_GENERIC_HARDIRQ,
it's not a big cost. (Both of the number of cpus and irqs are small.)
If a system is very big and CONFIG_GENERIC_HARDIRQ, it does
for_each_irq()
for_each_cpu()
- look up a radix tree
- read desc->irq_stat[cpu]
This seems not efficient. This patch adds kstat_irqs() for
CONFIG_GENRIC_HARDIRQ and change the calculation as
for_each_irq()
look up radix tree
for_each_cpu()
- read desc->irq_stat[cpu]
This reduces cost.
A test on (4096cpusp, 256 nodes, 4592 irqs) host (by Jack Steiner)
%time cat /proc/stat > /dev/null
Before Patch: 2.459 sec
After Patch : .561 sec
[akpm@linux-foundation.org: unexport kstat_irqs, coding-style tweaks]
[akpm@linux-foundation.org: fix unused variable 'per_irq_sum']
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Jack Steiner <steiner@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/stat shows the total number of all interrupts to each cpu. But when
the number of IRQs are very large, it take very long time and 'cat
/proc/stat' takes more than 10 secs. This is because sum of all irq
events are counted when /proc/stat is read. This patch adds "sum of all
irq" counter percpu and reduce read costs.
The cost of reading /proc/stat is important because it's used by major
applications as 'top', 'ps', 'w', etc....
A test on a mechin (4096cpu, 256 nodes, 4592 irqs) shows
%time cat /proc/stat > /dev/null
Before Patch: 12.627 sec
After Patch: 2.459 sec
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Jack Steiner <steiner@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov pointed out we have to prevent multiple-threads-inside-exec
itself and we can reuse ->cred_guard_mutex for it. Yes, concurrent
execve() has no worth.
Let's move ->cred_guard_mutex from task_struct to signal_struct. It
naturally prevent multiple-threads-inside-exec.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lock_task_sighand() grabs sighand->siglock in case of returning non-NULL
but unlock_task_sighand() releases it unconditionally. This leads sparse
to complain about the lock context imbalance. Rename and wrap
lock_task_sighand() using __cond_lock() macro to make sparse happy.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since userspace API of ptrace syscall defines @addr and @data as void
pointers, it would be more appropriate to define them as unsigned long in
kernel. Therefore related functions are changed also.
'unsigned long' is typically used in other places in kernel as an opaque
data type and that using this helps cleaning up a lot of warnings from
sparse.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is a control group interacting with the namespaces. When a
new namespace is created, a corresponding cgroup is automatically created
too. The cgroup name is the pid of the process who did 'unshare' or the
child of 'clone'.
This cgroup is tied with the namespace because it prevents a process to
escape the control group and use the post_clone callback, so the child
cgroup inherits the values of the parent cgroup.
Unfortunately, the more we use this cgroup and the more we are facing
problems with it:
(1) when a process unshares, the cgroup name may conflict with a
previous cgroup with the same pid, so unshare or clone return -EEXIST
(2) the cgroup creation is out of control because there may have an
application creating several namespaces where the system will
automatically create several cgroups in his back and let them on the
cgroupfs (eg. a vrf based on the network namespace).
(3) the mix of (1) and (2) force an administrator to regularly check
and clean these cgroups.
This patchset removes the ns_cgroup by adding a new flag to the cgroup and
the cgroupfs mount option. It enables the copy of the parent cgroup when
a child cgroup is created. We can then safely remove the ns_cgroup as
this flag brings a compatibility. We have now to manually create and add
the task to a cgroup, which is consistent with the cgroup framework.
This patch:
Sent as an answer to a previous thread around the ns_cgroup.
https://lists.linux-foundation.org/pipermail/containers/2009-June/018627.html
It adds a control file 'clone_children' for a cgroup. This control file
is a boolean specifying if the child cgroup should be a clone of the
parent cgroup or not. The default value is 'false'.
This flag makes the child cgroup to call the post_clone callback of all
the subsystem, if it is available.
At present, the cpuset is the only one which had implemented the
post_clone callback.
The option can be set at mount time by specifying the 'clone_children'
mount option.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul Menage <menage@google.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Cc: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fb_{read,write} access the framebuffer using lots of fb_{read,write}l's
but don't check that the file position is aligned which can cause problems
on some architectures which do not support unaligned accesses.
Since the operations are essentially memcpy_{from,to}io, new
fb_memcpy_{from,to}fb macros have been defined and these are used instead.
For Sparc, fb_{read,write} macros use sbus_{read,write}, so this defines
new sbus_memcpy_{from,to}io functions the same as memcpy_{from,to}io but
using sbus_{read,write}b instead of {read,write}b.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some ADP5588 functions take a pointer to an i2c_client, but if the i2c
header doesn't happen to be included first, we hit the standard "struct
declared inside parameter list" warnings from gcc. So add a simple
forward decl of the i2c_client struct.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Common code interprets this as a signed value (a negative value is used to
request dynamic ID allocation), so make sure the platform data has proper
types to support that.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 7444a72eff ("gpiolib: allow user-selection")
removed HAVE_GPIO_LIB Kconfig symbol, but the header file still uses the
name [to confuse readers wrt #ifdef/#else/#endif location].
The real Kconfig symbol nowadays is CONFIG_GPIOLIB.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph reported a nice splat which illustrated a race in the new stack
based kmap_atomic implementation.
The problem is that we pop our stack slot before we're completely done
resetting its state -- in particular clearing the PTE (sometimes that's
CONFIG_DEBUG_HIGHMEM). If an interrupt happens before we actually clear
the PTE used for the last slot, that interrupt can reuse the slot in a
dirty state, which triggers a BUG in kmap_atomic().
Fix this by introducing kmap_atomic_idx() which reports the current slot
index without actually releasing it and use that to find the PTE and delay
the _pop() until after we're completely done.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears i386 uses kmap_atomic infrastructure regardless of
CONFIG_HIGHMEM which results in a compile error when highmem is disabled.
Cure this by providing the needed few bits for both CONFIG_HIGHMEM and
CONFIG_X86_32.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
