IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
GPIO_S0_SC57 / GPIO_S0_SC61 can be muxed to PCU_UART_TXD / PCU_UART_RXD,
add a pinconf group for this.
On Bay Trail board schematics using these pins as UART these are
called UART3_TXD / UART3_RXD, name the pinconf group "uart3_grp"
to be consistent with the schematics.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For all the "score" pin-groups all the intel_pingroup-s to select
the non GPIO function are re-used for byt_score_gpio_groups[].
But this is incorrect since a pin-group includes the mode setting,
which for the non GPIO functions generally is 1, where as to select
the GPIO function mode must be set to 0.
So the GPIO function needs separate intel_pingroup-s with their own mode
value of 0.
Add a new PIN_GROUP_GPIO macro which adds a foo_gpio entry to each
pin-group defined this way and update byt_score_gpio_groups[] to point
to the new foo_gpio entries.
The "sus" usb_oc_grp usb_ulpi_grp and pcu_spi_grp pin-groups are special
because these have a non 0 mode value to select the GPIO functions and
these already have matching foo_gpio pin-groups, leave these are unchanged.
The pmu_clk "sus" groups added in commit 2f46d7f7e959 ("pinctrl: baytrail:
Add pinconf group + function for the pmu_clk") do need to use the new
PIN_GROUP_GPIO macro.
Fixes: 2f46d7f7e959 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* New agnostic driver to support Lunar Lake and newer platforms
* New driver for Intel Meteor Point-S (PCH for Meteor Lake-S)
* Update drivers to use new PM helpers
* Use RAII for locking in a few drivers (Raag, Andy)
* Reduce locking scope in some functions (Raag)
* Miscellaneous cleanups (Raag)
The following is an automated git shortlog grouped by driver:
alderlake:
- Switch to use Intel pin control PM ops
baytrail:
- Simplify code with cleanup helpers
- Move default strength assignment to a switch-case
- Factor out byt_gpio_force_input_mode()
- Fix types of config value in byt_pin_config_set()
broxton:
- Switch to use Intel pin control PM ops
cannonlake:
- Switch to use Intel pin control PM ops
cedarfork:
- Switch to use Intel pin control PM ops
denverton:
- Switch to use Intel pin control PM ops
elkhartlake:
- Switch to use Intel pin control PM ops
emmitsburg:
- Switch to use Intel pin control PM ops
geminilake:
- Switch to use Intel pin control PM ops
icelake:
- Switch to use Intel pin control PM ops
intel:
- Add Intel Meteor Point pin controller and GPIO support
- use the correct _PM_OPS() export macro
- Add a generic Intel pin control platform driver
- Revert "Unexport intel_pinctrl_probe()"
- allow independent COMPILE_TEST
- Refactor intel_pinctrl_get_soc_data()
- Move default strength assignment to a switch-case
- Make PM ops functions static
- Provide Intel pin control wide PM ops structure
jasperlake:
- Switch to use Intel pin control PM ops
lakefield:
- Switch to use Intel pin control PM ops
lewisburg:
- Switch to use Intel pin control PM ops
lynxpoint:
- Simplify code with cleanup helpers
meteorlake:
- Switch to use Intel pin control PM ops
sunrisepoint:
- Switch to use Intel pin control PM ops
tangier:
- simplify locking using cleanup helpers
- Move default strength assignment to a switch-case
- Enable 910 Ohm bias
tigerlake:
- Switch to use Intel pin control PM ops
-----BEGIN PGP SIGNATURE-----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=72T1
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v6.8-1
* New agnostic driver to support Lunar Lake and newer platforms
* New driver for Intel Meteor Point-S (PCH for Meteor Lake-S)
* Update drivers to use new PM helpers
* Use RAII for locking in a few drivers (Raag, Andy)
* Reduce locking scope in some functions (Raag)
* Miscellaneous cleanups (Raag)
The following is an automated git shortlog grouped by driver:
alderlake:
- Switch to use Intel pin control PM ops
baytrail:
- Simplify code with cleanup helpers
- Move default strength assignment to a switch-case
- Factor out byt_gpio_force_input_mode()
- Fix types of config value in byt_pin_config_set()
broxton:
- Switch to use Intel pin control PM ops
cannonlake:
- Switch to use Intel pin control PM ops
cedarfork:
- Switch to use Intel pin control PM ops
denverton:
- Switch to use Intel pin control PM ops
elkhartlake:
- Switch to use Intel pin control PM ops
emmitsburg:
- Switch to use Intel pin control PM ops
geminilake:
- Switch to use Intel pin control PM ops
icelake:
- Switch to use Intel pin control PM ops
intel:
- Add Intel Meteor Point pin controller and GPIO support
- use the correct _PM_OPS() export macro
- Add a generic Intel pin control platform driver
- Revert "Unexport intel_pinctrl_probe()"
- allow independent COMPILE_TEST
- Refactor intel_pinctrl_get_soc_data()
- Move default strength assignment to a switch-case
- Make PM ops functions static
- Provide Intel pin control wide PM ops structure
jasperlake:
- Switch to use Intel pin control PM ops
lakefield:
- Switch to use Intel pin control PM ops
lewisburg:
- Switch to use Intel pin control PM ops
lynxpoint:
- Simplify code with cleanup helpers
meteorlake:
- Switch to use Intel pin control PM ops
sunrisepoint:
- Switch to use Intel pin control PM ops
tangier:
- simplify locking using cleanup helpers
- Move default strength assignment to a switch-case
- Enable 910 Ohm bias
tigerlake:
- Switch to use Intel pin control PM ops
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use macros defined in linux/cleanup.h to automate resource lifetime
control in the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When ->pin_config_set() is called from the GPIO library (assumed
GpioIo() ACPI resource), the argument can be 1, when, for example,
PullDefault is provided. In such case we supply sane default in
the driver. Move that default assingment to a switch-case, so
it will be consolidated in one place.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is a piece of code that it being used at least twice.
Factor it out.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When unpacked, the config value is split to two of different types.
Fix the types accordingly.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The kernel.h is a mess of unrelated things and we only used it
as a proxy to array_size.h, hence switch from former to the latter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since Baytrail pinctrl device is not attached to acpi_lpss_pm_domain,
runtime PM serves no purpose here. Drop it and switch to pm_sleep_ptr()
as now we only have suspend and resume handles in place.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20231003114036.27674-2-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to update debounce pulse value in case debounce is to be
disabled. Break such a case where arg value is zero.
Fixes: 4cfff5b7af8b ("pinctrl: baytrail: consolidate common mask operation")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-gpio/d164d471-5432-4c3c-afdb-33dc8f53d043@moroto.mountain/
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cleaning up the driver to use pm_ptr() and *_PM_OPS() macros that
make it simpler and allows the compiler to remove those functions
if built without CONFIG_PM and CONFIG_PM_SLEEP support.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20230717172821.62827-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Raag Jadav <raag.jadav@intel.com> says:
This series exports common pinctrl functions that are used across
Intel specific platform drivers to PINCTRL_INTEL namespace and
reuses them into Baytrail, Cherryview and Lynxpoint drivers.
This helps reduce their code and memory footprint.
X86 kernels are fairly unikernels such that pinctrl-intel driver is
enabled by most Linux distributions and most Intel specific platform
drivers (inside drivers/pinctrl/intel) depend on it.
The only exception to this is Lynxpoint. But taking into account its
fairly old age, it wouldn't suffer much from pinctrl-intel dependency.
bloat-o-meter:
==============
Intel:
add/remove: 17/10 grow/shrink: 0/0 up/down: 375/-319 (56)
Total: Before=9598, After=9654, chg +0.58%
Baytrail:
add/remove: 1/6 grow/shrink: 0/2 up/down: 41/-441 (-400)
Total: Before=16538, After=16138, chg -2.42%
Cherryview:
add/remove: 1/6 grow/shrink: 2/0 up/down: 90/-272 (-182)
Total: Before=18133, After=17951, chg -1.00%
Lynxpoint:
add/remove: 1/6 grow/shrink: 0/1 up/down: 24/-354 (-330)
Total: Before=7836, After=7506, chg -4.21%
Link: https://lore.kernel.org/r/20230814060311.15945-1-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reuse common functions from pinctrl-intel driver.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230814060311.15945-3-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Consolidate common mask operation outside of switch cases and
limit IO operations to positive cases.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Invert if condition and get rid of redundant else.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230616203356.27343-4-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add warning for BYT_VAL_REG retrieval failure and continue such case
to avoid unintended reads/writes in pm_ops.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230616203356.27343-3-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce scope of spinlock to IO operations in ->dbg_show() hook
and save a few bytes.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-12 (-12)
Function old new delta
byt_gpio_dbg_show 890 878 -12
Total: Before=17029, After=17017, chg -0.07%
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230616203356.27343-2-raag.jadav@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The bias setting (pull-up or pull-down) are bit fields and
we never enable them both, hence use BIT() macro to define
them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use same formatting strings where it makes sense, so linker
will utilize only a single copy of it, otherwise make the
style similar to the rest of the messages of the close enough
semantics.
add/remove: 1/0 grow/shrink: 2/2 up/down: 91/-110 (-19)
Total: Before=17562, After=17543, chg -0.11%
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert driver to use generic data type and hence a new member in
the struct intel_function. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
While at it, switch to use hwirq variable instead of offset for
the sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a
derivative of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in
the Renesas drivers. Mainly sharing similar data between the
different SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmJBsSwACgkQQRCzN7AZ
XXOoVhAAhHW2FSXB8ud1mdyuN3CswMSiWrZqC8nveznHMcddzsDvZsGsAP8x6fKi
1CgTXDQblA/plpxqORvBDA8Ji9+z9NAilIMds1ZcMbPjpY1l63uD5VhWq7tpPN1H
ALnJAhc4rl1fkJ01U5sTtHJ8xibjpN690ZCrfzNwdLOQAUvXJ22zuyuIcSBFiSMv
ij4E2fejOj0ZN7rzb8xTxcaSWUrj5Kci5Eaq6yi/clKHaOrrV5r/tX9yo7uWF3mi
6UX/1IioougtMF2bhsoodQE5E5XN8Hjm2+VWULxBCsKjI1gKY/NR2GXeaHHJve8B
do3Y45cU+zZSWVo4mmlf/Z3+4npIQlMFe8LvDmBvb3ZopcbapuGiOSzYxT6aZA/z
WtGDDIaECcNF/dJCHwRugAsG5OhT0AYyNblMxsmW+ARoTocMlYPG8Jq4KEmIoIEz
m+UArJEe8asQlk4ebK/e0x2hbywgfN02ILO8OygpXpwsHAyx7pjDk7SABkzrAQLg
vTpI1i7q1hsYyeTm9RXJJd2VTe9fpYLTgjTa5bnqBQNcsyEd5o9QtH/IwARS/NP7
nNlZLUIUsOa782O6N4oT5JGb96a3cMxHv+hAIKcwhxK/54IYrGh+/BAORnfoe0Vo
h6pwKoUVE+L70t0RfmVqYK0EX6zsWSnb1NNNJFM+uLLpfFnx+1U=
=TY4V
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time. Just new driver code and improvements!
New drivers:
- New driver for the Broadcom BCM4908 SoC.
- New subdriver for Tesla FSD (Full Self Driving) SoC, a derivative
of the Samsung Exynos pin control driver.
- New driver for the Amlogic Meson S4 SoC.
- New driver for the Sunplus SP7021 SoC.
- New driver for the Microsemi Ocelot family ServalT SoC.
- New subdriver for Intel Alder Lake-M SoC.
- New subdriver for Intel Ice Lake-N SoC, including PCH support.
- New subdriver for Renesas R8A779F0 SoC.
- New subdriver for Mediatek MT8186 SoC.
- New subdriver for NXP Freescale i.MX93 SoC.
- New driver for Nuvoton WPCM450 SoC.
- New driver for Qualcomm SC8280XP SoC.
Improvements:
- Wakeup support on Samsung Exynos850 and ExynosAutov9.
- Serious and voluminous maintenance cleanup and refactoring in the
Renesas drivers. Mainly sharing similar data between the different
SoC subdrivers.
- Qualcomm SM8450 EGPIO support.
- Drive strength support on the Mediatek MT8195.
- Add some missing groups and functions to the Ralink RT2880"
* tag 'pinctrl-v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (188 commits)
pinctrl: mediatek: common-v1: fix semicolon.cocci warnings
pinctrl: nuvoton: wpcm450: Fix build error without OF
pinctrl: qcom-pmic-gpio: Add support for pm8450
dt-bindings: pinctrl: aspeed: Update gfx node in example
dt-bindings: pinctrl: rt2880: add missing pin groups and functions
pinctrl: ingenic: Fix regmap on X series SoCs
pinctrl: nuvoton: Fix return value check in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: off by one in wpcm450_gpio_register()
pinctrl: nuvoton: wpcm450: select GENERIC_PINCTRL_GROUPS
pinctrl: nuvoton: Fix sparse warning
pinctrl: mediatek: mt8186: Account for probe refactoring
pinctrl: mediatek: common-v1: Commonize spec_ies_smt_set callback
pinctrl: mediatek: common-v1: Commonize spec_pupd callback
pinctrl: mediatek: common-v1: Use common probe function
pinctrl: mediatek: common-v1: Add common probe function
pinctrl: mediatek: paris: Unify probe function by using OF match data
pinctrl/rockchip: Add missing of_node_put() in rockchip_pinctrl_probe
pinctrl: nomadik: Add missing of_node_put() in nmk_pinctrl_probe
pinctrl: berlin: fix error return code of berlin_pinctrl_build_state()
pinctrl: qcom: Introduce sc8280xp TLMM driver
...
On the Lenovo Yoga Tablet 2 830 / 1050 / 1051 models the 32KHz PMU clk,
which can be muxed externally to SUS pin 5 and/or 6 is used as a clock
for the audio codec.
On the 830 and 1050 models, with ship with Android as factory OS the
pin-muxing for this is not setup by the BIOS.
Add a pinconf group + function for the pmu_clk on SUS pin 5 and 6 to
allow setting the pinmux up from within the x86-android-tablets
platform code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223133153.730337-2-hdegoede@redhat.com
Some boards set the direct_irq_en flag in the conf0 register without
setting the correct trigger bits. The direct_irq_en flag just means that
the GPIO will send IRQs directly to the APIC instead of going through
the shared interrupt for the GPIO controller, in order for the pin to be
able to actually generate IRQs the trigger flags must configure the IRQ
as a level-high or level-low active IRQ.
Note testing shows that using edge trigger add the conf0 register level
does NOT work, instead edge triggering should be set at the IO-APIC level.
I believe that the direct_irq_en flag connects the output of the GPIO's IRQ
trigger block, which normally sets the status flag in the IRQ status reg at
0x800 to one of the IO-APIC pins according to the direct IRQ mux.
This means that the TRIG_LVL bit *must* be set, so that the GPIO's input
value is directly passed (1:1 or inverted) to the IO-APIC pin, if TRIG_LVL
is not set, selecting edge mode operation then on the first edge the
selected IO-APIC pin goes high, but since no write-to-clear write will be
done to the IRQ status reg at 0x800, the detected edge condition will never
get cleared.
This APIC pin stuck high condition can be observed with the pin configured
as level-high active, in the form of an interrupt storm. Clearing the
TRIG_MASK bits of conf0 stops the storm, reconfiguring them as edge again
results in a storm again as soon as the edge is triggered once.
Detect invalid trigger flags, log a FW_BUG warning when encountering this
and clear the direct_irq_en flag so that a driver can actually use the pin
as IRQ through gpiod_to_irq().
Specifically this allows the edt-ft5x06 touchscreen driver to use
INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet,
accompanied by the following new log message
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger, clearing
The new byt_direct_irq_sanity_check() function also checks that the
pin is actually appointed to one of the 16 direct-IRQs which the GPIO
controller supports and on success prints debug messages like these:
byt_gpio INT33FC:02: Pin 0: uses direct IRQ 0 (IO-APIC 67)
byt_gpio INT33FC:02: Pin 15: uses direct IRQ 2 (IO-APIC 69)
This is useful to figure out the GPIO pin belonging to ACPI
resources like this one: "Interrupt () { 0x00000043 }" or
the other way around.
The strict checking of valid trigger flags this introduces does result in
FW_BUG messages on quite a few devices. E.g. on the Yoga Tablet 2 1051L:
byt_gpio INT33FC:00: [Firmware Bug]: pin 92: direct_irq_en set but no IRQ assigned, clearing
byt_gpio INT33FC:00: [Firmware Bug]: pin 93: direct_irq_en set but no IRQ assigned, clearing
These 2 also have mux set to 7 and fall + rise + level trigger bits set,
presumably something has written 0xffffffff to their conf0 registers
byt_gpio INT33FC:02: Pin 3: uses direct IRQ 1 (IO-APIC 68)
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger (conf0: 2803cc00h), clearing
Most tablets seem to have this, looking at DSDTs this seems intended for
use with an I2C HID sensor-hub and is still set on devices without one.
To make sure this does not cause any regressions this has been tested,
including checking disabled direct-IRQs are not used in the DSDT,
on the following devices:
Asus ME176C
Asus TF103C
Chuwi Vi10 (with its Windows BIOS)
HP x2 10-n000nd
Lenovo Yoga Tablet 2 1050L (Android version, without EC, with buggy DSDT)
Lenovo Yoga Tablet 2 1051L (Windows version, with EC)
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The byt_irq_type function ends with the IRQ masked, this means that calls
to irq_set_irq_type() while the IRQ is enabled end up masking it, which
is wrong. Add the IRQCHIP_SET_TYPE_MASKED flag to fix this.
This will make the IRQ core call mask() + unmask() on the IRQ around
a set_type() call when the IRQ is enabled at the type of the call.
Note in practice irq_set_irq_type() getting called while the IRQ is enabled
almost never happens. I hit this with a buggy DSDT where a wrongly active
(_STA returns 0xf) I2C ACPI devices point to an IRQ already in use by an
_AEI handler, leading to the irq_set_irq_type() call in
acpi_dev_gpio_irq_get_by() getting called while the IRQ is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c742f ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d66 ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1d5 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We may use now available struct intel_pinctrl in the driver.
No functional change implied.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use local variable to keep device pointer in order to increase readability
of the driver.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to keep pointer to struct platform_device, which is container
of struct device, because the latter is what have been used everywhere outside
of ->probe() path. In any case we may derive pointer to the container when
needed.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is a logical continuation of the commit 5fbe5b5883f8 ("gpio: Initialize
the irqchip valid_mask with a callback") to split IRQ initialization to
hardware and valid mask setup parts.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
After commit 5ea422750a9f ("pinctrl: baytrail: Pass irqchip when
adding gpiochip") the GPIO IRQ chip structure is being initialized
under conditional when IRQ resource has been discovered. But that
commit left aside the assignment of ->init_valid_mask() callback
that is done unconditionally.
For sake of consistency and preventing some garbage in GPIO IRQ chip
structure group initialization together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: 9f573b98ca50 ("pinctrl: baytrail: Update irq chip operations")
Depends-on: ca8a958e2acb ("pinctrl: baytrail: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Update North Community pin list to be more clear about pin functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 39ce8150a079 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a079 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl2D6y0ACgkQQRCzN7AZ
XXNAfw//Zh0zkrwVSiDU7xgjIgLpngkmPeDoFZoPW5Uqh6G3KlabkE0y7CXZT2kd
hZU0v8CW/947t2zxNev6nNUPumfaTJsj5btVAvF8+QE2lnnbs3Id2mPVPK/mMUs+
bOVFkMMFvGzsY2TaKiJSgOiTe8LoUUl2tJ25mFRBwgtPWYJh2NLVwbzScv+KTBX2
Yy1UhltfWaobyPGgJucZn2yDbkZQeDLyKaExsL9jKBO9rAf8iwSOwkxEz5hLGRri
ejubLV2C5WDcAYIMO2WscFm/0Cxv8ooWBlGTG3+v3P1eaB7l7rYkGpVkoRJpS7gr
Qzf0z1PjVudCcwomkf7ZXJFVHCEkWe86oT4plII9TiZ0b5YpwxYA3Rzakrpb3K7E
gxCuMR1PQK9/2VcqtnXjV2N40KJNRhsAGx47YK3mZxFQun8ksLDTSwKCEPvQ5GT6
3CSYtqVkqgpRaj1MIe+QrFE5Y2bNPjYqXF8kqh5hz/2FWZErbaRuPuKscYh7x0Z4
wY157HEYTlSnSs3nHFtPO3qeXt0i2MNOKVpIlyKzUnafPoyxcnqaB/ZMt5Dp3ygX
NJI3xqULdSzXRpjj/oChCKzuNd9CmxO6yWMIK32f4Gdc3T1wmpBlOTIrHKUA5aZf
KN38L/8iGnzvOKC57552eFpTXaF4Plh2y7e0xQkq4eshhHpz8H8=
=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
