IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Command queue descriptor page size is 4KB and not the page size used by the
kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 requires at least one interrupt vector for completions so fix the minvec
argument to pci_enable_msix_range() accordingly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call request module on mlx5_ib so it will be available for applications
requiring it, such as installers that require boot over IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.
Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify bcmgenet driver so that it can be used on Broadcom 7xxx
MIPS-based STB platforms without a device tree.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce stack use by using kmemdup and not using a very
large struct on stack.
In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Getting the pf_id from the function number was a good place to start,
but when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number. This works in NPAR mode as well.
Change-ID: I65e3dd6c97594890c2bad566b83cc670b1dae534
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ needs to have at least as many entries as VFs, or the VFs will
get errors from the FW when they send messages to the PF. Since we don't
know how many VFs we'll end up with, just set up 128 descriptors.
Change-ID: I04ae3d1c7faf09110eb782214e9c05aeb62a6c59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.
Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.
Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.
Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase reset delay to ensure all internal caches are properly flushed
in worst case scenario.
Change-ID: I6f059a9e024fbf9ef1debd32497eed21369957fc
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated. Since we're
using rtnl_link_stats64 in other parts of the driver, we should use it
here as well. We've just been lucky that the field definitions are the
same sizes.
Change-ID: I19fc71619905700235dcdf0d3c8153aec81d36de
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.
It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.
This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).
The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.
Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds additional text description for base pf0 and flow director
generated interrupts. Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.
Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments. This makes the user interface much more forgiving and user
friendly.
Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.
Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In sky2_change_mtu setting B0_IMSK to 0 may be delayed due to PCI write posting
which could result in irqs being still active when synchronize_irq is called.
Since we are not prepared to handle any further irqs after synchronize_irq
(our resources are freed after that) force the write by a consecutive read from
the same register.
Similar situation in sky2_all_down: Here we disabled irqs by a write to B0_IMSK
but did not ensure that this write took place before synchronize_irq. Fix that
too.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a spurious interrupt dont forget to reenable the interrupts that
have been masked by reading the interrupt source register.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pxa168_eth_open() the irqs are enabled before napi. This opens a tiny time
window in which the irq handler is processed, disables irqs but then is not able
to schedule the not yet activated napi, leaving irqs disabled forever (since
irqs are reenabled in napi poll function).
Fix this race by activating napi before irqs are activated.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pci_dev_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using global variables we are going to use dynamically allocated
memory. It allows to append a support of more than one ethernet adapter which
might have different settings simultaniously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves couple of issues in ixgbevf_probe/remove():
1. Fix a case where adapter->state is tested after free_netdev() this is
same as the patch for ixgbe from Daniel Borkmann <dborkman@redhat.com>:
commit b5b2ffc0574e1f27 ("ixgbe: fix use after free adapter->state test in ixgbe_remove/ixgbe_probe")
2. Move pci_set_drvdata() after all the error checks in ixgbevf_probe() and
then add a check in ixgbevf_probe() to avoid running the cleanup functions
twice in cases where probe failed.
CC: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds initial support for VFs on a new mac - X550.
The patch adds the basic structures and device IDs for the X550 VFs
that would allow the driver to load and pass traffic.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.
This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods. Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification. These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the shared code checksum calculation function only
returns a u16 and cannot return an error code. Unfortunately
a variety of errors can happen that completely prevent the
calculation of a checksum. So, change the function return value
from a u16 to an s32 and return a negative value on error, or the
positive checksum value when there is no error.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some X550 procedures will be using CS4227 PHY and need to
perform combined read and write operations. This patch
adds those methods.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550 hardware will use more bits in the mask, so change
the prototypes to match. This larger mask will require changes
in callers which use the higher bits. Likewise since X550 will
use different semaphore mask values and will use the lan_id
value. So save these values in the ixgbe_phy_info struct.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since on X550 we use host interface commands to read,write and erase
some commands require more time to complete. So this adds a timeout
parameter to ixgbe_host_interface_command as wells as a return_data
parameter allowing us to return with any data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key. This patch will enable this functionality
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accessing the CIAA/D register can block access to the PCI config space.
This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.
In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.
CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the tail writes for the ixgbe descriptor queues. The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.
It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME within #ifdef blocks depending on
CONFIG_PM may be dropped now.
Do that in the e1000e and igb network drivers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wake On Lan was not working on laptop DELL Vostro 1500.
If WOL was turned on, BCM4401 was powered up in suspend mode. LEDs blinked.
But the laptop could not be woken up with the Magic Packet. The reason for
that was that PCIE was not enabled as a system wakeup source and
therefore the host PCI bridge was not powered up in suspend mode.
PCIE was not enabled in suspend by PM because no child devices were
registered as wakeup source during suspend process.
On laptop BCM4401 is connected through the SSB bus, that is connected to the
PCI-Express bus. SSB and B44 did not use standard PM wakeup functions
and did not forward wakeup settings to their parents.
To fix that B44 driver enables PM wakeup and registers new wakeup source
using device_set_wakeup_enable(). Wakeup is automatically reported to the parent SSB
bus via power.wakeup_path. SSB bus enables wakeup for the parent PCI bridge, if there is any
child devices with enabled wakeup functionality. All other steps are
done by PM core code.
Signed-off-by: Andrey Skvortsov <Andrej.Skvortzov@gmail.com>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silences various sparse warnings
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker ports will use new "swdev" hwmode for bridge port offload policy.
Current supported policy settings are BR_LEARNING and BR_LEARNING_SYNC.
User can turn on/off device port FDB learning and syncing to bridge.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
