IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The generic ID can be used by topology:
- Toplogy can create FE links and set their ID, machine drivers will
be notified and check this ID for machine-specific init.
- Toplogy can use the ID to find existing BE & CC links and further
configure them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake platform has 3 pin widgets in HDMI codec. This patch adds
3 FE and BE dai links to support these in rt286 machine
Also add jack initialization for each of the device.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMIC BE can have 2 or 4 channels supported. The DMIC fixup needs
to take this into account.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only add ignore suspend flag for some DAIs and not all.
This patches removes it from the DAIs where we do not support
this
It also marks the endpoints for which ignore_suspend should be
enabled
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vunny Sodhi <vunnyx.sodhi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM Machine map for machine was not specifying the paths
correctly.
The correct order should be:
"DMIC01 Rx" (SoC DMIC BE), connected to "DMIC AIF" (DMic Codec
AIF) and then "DMic" (DMic codec Input) connected to "SoC DMIC"
(Machine DMIC MIC Widget)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since in Skylake we support another DAI for DMIC quad capture,
add a dailink for this as well. Also specify constrains for DMIC
FE devices and fixup for DMIC BEs
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM ops are required so that DAPM will suspend and resume the DSP
pipelines properly
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ref configuration for Skylake, we support only 16bit, 48KHz,
stereo audio, so specify these as constrains for the devices
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSP0 FMT uses 24 bits so fix to the value to 24 bits
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the SKL I2S machine driver using Realtek ALC286S codec
in I2S mode.
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
