IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Some registers had wrong default values in cs42l42_reg_defaults[].
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211015133619.4698-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.
The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 585e7079de0e ("ASoC: cs42l42: Add Capture Support")
Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When capture and playback substreams are both running at the same time,
cs42l42_pcm_hw_params() would be called for each direction. The first
call will configure the PLL. The second call must not write the PLL
configuration registers again if the first substream is already running,
as this could destabilize the PLL.
The DAI is marked symmetric sample bits and sample rate, so the two
directions will always have the same SCLK (I2S always has 2 channel slots
so the DAI does not need to require symmetric channels to guarantee the
same SCLK). However, since cs42l42_pll_config() is checking for an active
stream it may as well test that the requested SCLK is the same as the
currently active configuration.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A little pop can be heard obviously from HP while playing a silent.
This patch fixes it by using two functions:
1. Enable HP 1bit output mode.
2. Change the charge pump switch size during playback on and off.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211014094054.811-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several things the patch adding the support for 'I2S Reference'
got wrong:
- "None" selection is in fact equals to last selected reference
- The custom put overrides RX/TX len, TDM slot sizes, etc
- the enum is useless in most part for the reference tracking
- there is no need for EXT control as there is a single bit in
RT1011_TDM1_SET_1 register (bit 7) which selects the reference
- it was using ucontrol->value.integer.value[0] in the put/get callbacks
which causesed access to 'I2S Reference' enum with alsamixer to fail
Complements: c3de683c4d1d ("ASoC: rt1011: Fix 'I2S Reference' enum control caused error")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211013123300.11095-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa22f ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This drops the rt9210 support due to a race with a new version being
sent out for some incremental changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
Access to 'I2S Reference' enum causes alsamixer to fail to load:
$ alsamixer
cannot load mixer controls: Invalid argument
cml_rt1011_rt5682 cml_rt1011_rt5682: control 2:0:0:TL I2S Reference:0: access overflow
The reason is that the original patch adding the code was using
ucontrol->value.integer.value[0]
instead the correct
ucontrol->value.enumerated.item[0]
for an ENUM control.
Fixes: 87f40af26c262 ("ASoC: rt1011: add i2s reference control for rt1011")
Reported-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211011144518.2518-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure the default 0dB playback path is always used.
The code that set FULL_SCALE_VOL based on LOAD_DET_RCSTAT was
spurious, and resulted in a -6dB attenuation being accidentally
inserted into the playback path.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211011144903.28915-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98927 codec on some devices (i.e. Xiaomi Mi A2 Lite phone) requires
hardware-resetting the codec by driving a reset-gpio. This series adds
support for it through an optional reset-gpios property.
v4:
* Correctly assert/deassert the GPIO states
* Wait for the i2c port to be ready after reset
* Reset device when removed
v3:
* Fix indentation on the dev_err_probe line
v2:
* Use dev_err_probe instead of dev_err
Alejandro Tafalla (2):
ASoC: max98927: Handle reset gpio when probing i2c
dt-bindings: sound: max98927: Add reset-gpios optional property
.../devicetree/bindings/sound/max9892x.txt | 3 +++
sound/soc/codecs/max98927.c | 25 +++++++++++++++++++
sound/soc/codecs/max98927.h | 1 +
3 files changed, 29 insertions(+)
--
2.33.0
When the system plays a sound immediately after resuming from S3,
it could hear a little pop from headphones.
It is due to the HP was unmuted before the completion of
jack re-detection finished in parallel.
This patch adds a lock to make sure the HP unmute after jack detect handler,
and adds a few depop changes.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211007085519.12543-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is to fix audio 3.5mm jack detection failure
on wcd938x codec based target.
Fixes: bcee7ed09b8e (ASoC: codecs: wcd938x: add Multi Button Headset Control support)
Signed-off-by: Venkata Prasad Potturu <potturu@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1633614619-27026-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices using the NAU8824 have only one speaker. To still have things
working properly this requires the left + right channels to both be mixed
to the left speaker output.
This mixer setup is done by userspace based on UCM profiles. But this
requires userspace to know that there is a mono-speaker. Add a helper
function (for the machine driver) to get a components string providing
this info.
This is done inside the codec driver because the codec driver already
has a DMI quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211002211459.110124-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk mechanism to allow specifying that active-high jack-detection
should be used on platforms where this info is not available in devicetree.
And add an entry for the Cyberbook T116 tablet to the DMI table, so that
jack-detection will work properly on this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211002211459.110124-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The NAU8824_JACK_LOGIC define was wrong, for active high jack-detect
to work bit 1 needs to be set, rather then bit 0.
The correct bit was found in the Android kernel source dump for
a Cyberbook T116 tablet; and this was also tested on that same tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211002211459.110124-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new IRQF_NO_AUTOEN flag when requesting the IRQ, rather then
disabling it immediately after requesting it.
This fixes a possible race where the IRQ might trigger between requesting
and disabling it; and this also leads to a small code cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211003132255.31743-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new IRQF_NO_AUTOEN flag when requesting the IRQ, rather then
disabling it immediately after requesting it.
This fixes a possible race where the IRQ might trigger between requesting
and disabling it; and this also leads to a small code cleanup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211003132255.31743-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is for codec NAU88L21 of Nuvoton Technology Corporation.
The NAU88L21 is an ultra-low power high performance audio codec that
supports both analog and digital audio functions.
Signed-off-by: Seven Lee <wtli@nuvoton.com>
Link: https://lore.kernel.org/r/20211001103108.3297848-1-wtli@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the system resumes from S3, if the system plays a beep,
there is continuous "Zizi.." noise from HP that could be heard.
It is caused by the SAR mode switch during the combo jack
re-detection which be executed parallelly in a workqueue
after the system resumes.
This patch changes the behavior of SAR mode switch to
avoid this issue.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211001074113.2223-2-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec's ASRC was enabled, the DA and AD filters use
the reference clk which tracks the I2S clks.
And if the I2S clks' timing of open and close are not expected,
this patch allows the filters to switch to use sysclk if
ASRC's ref clks disappeared and could fix the below possible issues:
1. Avoid DA filter to keep surplus samples.
2. Avoid that AD filter works failed during dapm's power on.
For example,
if I2S clks were closed before dacdat during playback off
due to jack unplug, it causes ref clks disappeared and
DA filter remained some samples which will produce pop noise
on the next HP playback.
ASRC auto-disable could clear the samples during the playback off.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211001074113.2223-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI clock is only used in I2S mode, to make it clear
and to fix clock resource release issue, we move CCF clock
related code to rt5682_i2c_probe to fix clock
register/unregister issue.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/20210929054344.12112-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove a repeated "#include <linux/firmware.h>" in line 32.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Acked-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210929123217.5240-1-guozhengkui@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 1d25684e2251 ("ASoC: nau8824: Fix open coded prefix handling")
replaced the nau8824_dapm_enable_pin() helper with direct calls to
snd_soc_dapm_enable_pin(), but the helper was using
snd_soc_dapm_force_enable_pin() and not forcing the MICBIAS + SAR
supplies on breaks headphone vs headset and button-press detection.
Replace the snd_soc_dapm_enable_pin() calls with
snd_soc_dapm_force_enable_pin() to fix this.
Cc: stable@vger.kernel.org
Fixes: 1d25684e2251 ("ASoC: nau8824: Fix open coded prefix handling")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210929201512.460360-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series of patches gradually separates the ASoC specific wm_adsp
code from that required to manage firmware in Cirrus Logic DSPs.
The series starts with renaming, progresses to splitting the
functionality before finally moving the independent functionality into
drivers/firmware so that it can be used by both the existing ASoC
wm_adsp and new non-audio parts.
Charles Keepax (3):
ASoC: wm_adsp: Move check for control existence
ASoC: wm_adsp: Switch to using wm_coeff_read_ctrl for compressed
buffers
ASoC: wm_adsp: Move sys_config_size to wm_adsp
Simon Trimmer (13):
ASoC: wm_adsp: Remove use of snd_ctl_elem_type_t
ASoC: wm_adsp: Cancel ongoing work when removing controls
ASoC: wm_adsp: Rename generic DSP support
ASoC: wm_adsp: Introduce cs_dsp logging macros
ASoC: wm_adsp: Separate some ASoC and generic functions
ASoC: wm_adsp: Split DSP power operations into helper functions
ASoC: wm_adsp: Separate generic cs_dsp_coeff_ctl handling
ASoC: wm_adsp: Move check of dsp->running to better place
ASoC: wm_adsp: Pass firmware names as parameters when starting DSP
core
ASoC: wm_adsp: move firmware loading to client
ASoC: wm_adsp: Split out struct cs_dsp from struct wm_adsp
ASoC: wm_adsp: Separate wm_adsp specifics in cs_dsp_client_ops
firmware: cs_dsp: add driver to support firmware loading on Cirrus
Logic DSPs
MAINTAINERS | 11 +
drivers/firmware/Kconfig | 1 +
drivers/firmware/Makefile | 1 +
drivers/firmware/cirrus/Kconfig | 5 +
drivers/firmware/cirrus/Makefile | 3 +
drivers/firmware/cirrus/cs_dsp.c | 3109 ++++++++++++++++
include/linux/firmware/cirrus/cs_dsp.h | 242 ++
.../linux/firmware/cirrus}/wmfw.h | 8 +-
sound/soc/codecs/Kconfig | 1 +
sound/soc/codecs/cs47l15.c | 22 +-
sound/soc/codecs/cs47l24.c | 20 +-
sound/soc/codecs/cs47l35.c | 24 +-
sound/soc/codecs/cs47l85.c | 32 +-
sound/soc/codecs/cs47l90.c | 34 +-
sound/soc/codecs/cs47l92.c | 20 +-
sound/soc/codecs/madera.c | 18 +-
sound/soc/codecs/wm2200.c | 30 +-
sound/soc/codecs/wm5102.c | 16 +-
sound/soc/codecs/wm5110.c | 24 +-
sound/soc/codecs/wm_adsp.c | 3188 ++---------------
sound/soc/codecs/wm_adsp.h | 105 +-
21 files changed, 3794 insertions(+), 3120 deletions(-)
create mode 100644 drivers/firmware/cirrus/Kconfig
create mode 100644 drivers/firmware/cirrus/Makefile
create mode 100644 drivers/firmware/cirrus/cs_dsp.c
create mode 100644 include/linux/firmware/cirrus/cs_dsp.h
rename {sound/soc/codecs => include/linux/firmware/cirrus}/wmfw.h (91%)
--
2.33.0
As part of moving to remove the old style defines for the bus clocks update
the ak4458 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920163817.16490-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ak5558 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920164753.17030-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ak4671 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920164211.16718-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the alc5623 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920165036.17142-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the cpcap driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210921213034.31427-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ad193x driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916142232.33914-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some headsets require very different comparator thresholds for type detection,
as well as longer settling times. In order to detect a larger number of headsets,
use 2 thresholds to give maximum coverage (1.25V and 1.75V), as well as a longer
settling time of 100ms. This will not affect default audotodetect mode
and applies to manual mode type detection only.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210927111437.18113-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adav80x driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-6-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adau1977 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-5-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adau17x1 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-4-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adau1701 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-3-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adau1373 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the adau1372 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916151806.20756-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ad1836 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916142125.7226-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ak4642 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920164042.16624-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The versioning scheme was changed in an earlier patch, which caused the version
being used to initialize WCD9335 to be interpreted as if it was WCD937X, which
changed code paths causing broken headphones output. Pass WCD9335 instead of
WCD9335_VERSION_2_0 to wcd_clsh_ctrl_alloc to fix it.
Fixes: 19c5d1f6a0c3 ("ASoC: codecs: wcd-clsh: add new version support")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210925022339.786296-1-y.oudjana@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the alc5632 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920165128.17224-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the ak4104 driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210916150922.20183-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
