IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
sil24_interrupt() loads host->ports[i] into a local variable,
validates it, and then loads the value again in the call to
sil24_host_intr(). This patch replaces the second load by a
reference to the local variable.
This is safe since no side-effects have occurred since the
initial load. It also improves readability since it makes
it clear that the parameter to sil24_host_intr() is the same
value which was just validated.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some embedded platforms, such as blackfin, the gpio interrupt for
IDE interface is designed to be triggered with high voltage. The gpio
port should be configured properly by set_irq_type() when register
the irq. This patch enable the generic pata platform driver to
accept platform irq flags data.
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch applies some trivial cleanups to sata_promise:
- repair whitespace damage
- correct comment at board_2057x_pata definition
- pull SATAII TX4 support code out to separate functions
- rename ata_nr to ata_no for consistency with libata's port_no
- remove some init-time debug printks (requested by Jeff)
This patch should cause no behavioural changes, except for
the removed printks.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
drivers/ata/sata_promise.c | 56 ++++++++++++++++++---------------------------
1 files changed, 23 insertions(+), 33 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix various bugs in pio/mwdma mode programming.
* Control bits in the timing register wasn't cleared properly while
programming PIO mode.
* MWDMA mode programming cleared the wrong part of control bits.
* MWDMA mode programming cleared udma_mask even when the controller
doesn't support UDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sx4:
- describe overall driver theory of operation
- add a few constants that will be used in the future
sata_via:
- remove mention of an old-EH function that is going away
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* convert tabs to spaces
* convert some hex numbers to (1 << n) preferred format
* document i2c and timer control register bits
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make it easier to verify which struct initializers are present, by
presenting them in the order in which they are defined in the API
header.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH. Remove.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the register offset table more maintainable.
From the 'sii-lbt' branch, which enables the LBT chip feature.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci: enable sg segment clustering
The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->cbl == ATA_CBL_SATA indicates SATA cable while ap->flags &
ATA_FLAG_SATA indicates SATA host port. Till now they always gave the
same result but SATA/PATA bridge handling will change that. Switch to
ATA_FLAG_SATA test if we're testing for host port type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTM/_STM support. acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle. A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend. _STM is executed in ata_acpi_on_resume(). With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.
ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used. These two
functions are responsible for determining whether specific ACPI method
is used and when.
On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag. This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).
On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF. _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies. As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.
If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure. If it fails again on the second try, ACPI is disabled
on the device. Note that successful configuration clears ACPI failed
status.
With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume(). As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add missing LOCKING: and RETURNS: to function comment.
* Don't conditionalize warning messages with ata_msg_probe(). Print
directly with KERN_WARNING.
* Drop duplicate debug messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch cleans up ata_acpi_exec_tfs() and its friends.
* Rename taskfile_array to ata_acpi_gtf and make it __packed as it's
used as argument to ACPI method, and use pointer to ata_acpi_gtf and
number of taskfiles to represent _GTF taskfiles instead of a pointer
casted into unsigned long and byte count. This makes argument
re-checking in do_drive_set_taskfiles() unnecessary.
* Pointer in void * not in unsigned long.
* Clean up do_drive_get_GTF() error handling and make
do_drive_get_GTF() return number of taskfiles on success, 0 if _GTF
doesn't exist or doesn't contain valid ata. -errno on other errors.
* Remove superflous check for acpi->buffer.pointer.
* Update taskfile_load_raw() such that printed messages look similar
to the messages printed by ata_eh_report().
* s/do_drive_get_GTF/ata_dev_get_GTF/
s/do_drive_set_taskfiles/ata_dev_set_taskfiles/
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add acpi_handle to ata_host and ata_port. Rename
ata_device->obj_handle to ->acpi_handle and move it above such that
it doesn't get cleared on reconfiguration.
* Replace ACPI node association which ata_acpi_associate() which is
called once during host initialization. Unlike the previous
implementation, ata_acpi_associate() uses ATA_FLAG_ACPI_SATA to
choose between IDE or SATA ACPI hierarchy and uses simple child look
up instead of recursive walk to match the nodes. This is way safer
and simpler. Please read the following message for more info.
http://article.gmane.org/gmane.linux.ide/17554
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are some devices (for example Dell Multimedia Keyboard SK-8135) that have
a volume control knob which generates relative events instead of absolute.
hid-input maps them to ABS_VOLUME. HUT pages don't restrict volume to absolute
values.
Adding REL_VOLUME doesn't seem feasible, nothing knows how to handle it. This
patch translates relative ABS_VOLUME events into appropriate number of series
of VOLUME_UP or VOLUME_DOWN events respectively, so that userspace sees the
correct values in the end.
kernel.org bugzilla 5233
Reported-by: Jochen Eisinger <jochen@penguin-breeder.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This keyboard has wireless mouse which has left, middle, right buttons and
2-dimensional scrolling wheel. Unfornetuly, this wheel reports side scrolling
events and 11 or 12 button events at the same time.
I've wrote a patch to fix this mapping. I'm not sure if this mapping is proper
for buttons, because , for example, there is no entry for "burn cd" in input.h.
The patch also supress 11 and 12 button events from mouse when you scroll the
wheel left and right. With this patch, only side scrolling events are
reported. (This mouse has only 4 buttons and 2D wheel. There is no such
buttons like 11 and 12.)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When setting the autocentering of PID devices, PID_DIRECTION_ENABLE is not
being explicitely set to 1. This results in autocentering working only on the
vertical axis when this field is preset to 0.
Fix that by setting it explicitely to 1 when preparing the set_effect report
for autocentering spring effect.
Signed-off-by: Diogo Kastrup <dk@bighost.com.br>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Lately there have been quite a lot of bug reports against broken devices
which require us to fix their report descriptor in the runtime, before it
is passed to the HID parser. Those devices have eaten quite an amount of
our quirks space, which isn't particularly necessary - the quirks are not
needed after the report descriptor is parsed, and they just consume bits.
Therefore this patch separates the quirks for report descriptor fixup, and
moves their handling into separate code. The quirks are then forgotten as
soon as the report descriptor has been parsed.
Module parameter 'rdesc_quirks' is introduced to be able to modify these
quirks in runtime in a similar way to 'quirks' parameter for ordinary HID
quirks.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices manufactured by NCR have userspace hiddev-based drivers,
which do all the necessary device querying by themselves. The devices
must not be queried directly by the generic HID driver, as reported by
NCR engineers.
Cc: Petr Ostadal <postadal@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Petalynx Maxter remote control [1] 0x18b1/0x0037 emits 0xfa and 0xfc from
consumer page (reserved in HUT 1.12) for back and more keys. It also emits
a few usages from LOGIVENDOR page, which need adding.
Also, this device has broken report descriptor - the reported maximum is too
low - it doesn't contain the range for 'back' and 'more' keys, so we need to
bump it up before the report descriptor is being parsed.
Besides all this, it also requires NOGET quirk.
This patch does so.
[1] http://www.elmak.pl/index.php?option=com_phpshop&page=shop.browse&category_id=14&ext=opis&lang=en
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When comparing usb vs ps2 / testing the keycodes generated for the easy access
keys on my trust (microsoft compatible) keyboard. I noticed the search key
generated the keycode for find when connected through USB. This lead me to
check the consumer page mappings in hid-input.c . And it turns out the the
mapping for ID 0x221 deviates from the HUT standard document:
http://www.usb.org/developers/devclass_docs/Hut1_12.pdf
Currently it is incorrectly mapped to find, whereas it should be mapped to
search. I also added missing bindings for ID 0x21f, the real find and for
0x222, goto.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch provides support for the Gameron dual psx adaptor. The
modification is to add the quirk HID_QUIRK_MULTI_INPUT for this
specific USB device.
Signed-off-by: Julien Eyries <jeyries@yahoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as914) replaces a call to flush_scheduled_work() with
cancel_work_sync(), in order to help avoid potential deadlocks.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft SideWinder GameVoice driver is a trivial device with a few buttons
(0x09 HID usage) and an audio connector, which just forwards the audio input
into oridinary sound card present in the computer.
Despite this fact, the only interface of this device reports itself as a
Telephony/Headset type of HID device. This is apparently incorrect - the device
itself doesn't provide any audio/telephony functionality. This is achieved in
userland application which only needs to receive the button events from the HID
driver.
This patch establishes a new quirk which forces hid-input to claim a device it
will otherwise leave untouched.
Reported-by: Tomas Carnecky <tom@dbservice.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Chicony KU-0418 (aka Saitek PZ08AU gaming keyboard) has a separate
"tactical pad" with 11 non-functional buttons - they generate usage
codes from 0xff00 (MSVENDOR) usage page. Special case handling for
this keyboard added, so no later clash with MSVENDOR mappings is going
to occur.
Pointed out in bugzilla #7352
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There have been many reports recently about broken HID devices, the
diagnosis of which required users to recompile their kernels in order
to be able to provide debugging output needed for coding a quirk for
a particular device.
This patch makes CONFIG_HID_DEBUG default y if !EMBEDDED and makes it
possible to control debugging output produced by HID code by supplying
'debug=1' module parameter.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Changes to last version:
- spelling fix
- cleaned up probe code
Thomas.
Ethernet driver for EISA only SNI RM200/RM400 machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes to last version:
- use netdev_alloc_skb
- make init_rx_bufs just fail and not panic, if skb alloc fails
- don/t free_irq, if request_irq failed
Thomas.
Extracted chip specific code out of lasi_82596.c and placed into a lib82596.c
to make it usable for other 82596 drivers
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was mistakenly set to interrupt on the second packet instead of first, causing
some interesting latency behaviour.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It does not really make sense to update the RX config register
before the mac filtering registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Merged from Realtek's r8169-6.001 driver.
I have added some locking to protect against the arp monitoring
timer in the bonding driver. Accessing the configuration registers
is otherwise performed under RTNL locking.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It does not cost much and it will ease the identification of (so far)
unknown devices.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
