IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently the data transmission arbitration algorithm - DataTranARB
field on TQAVCTRL reg - is always set to CBS when the Tx mode is
changed from legacy to 'Qav' mode.
Make that configuration a bit more granular in preparation for the
upcoming Launchtime enabling patches, since CBS and Launchtime can be
enabled separately. That is achieved by moving the DataTranARB setup
to igb_config_tx_modes() instead.
Similarly, when disabling CBS we must check if it has been disabled
for all queues, and clear the DataTranARB accordingly.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this function retrieve what it needs from the Tx ring being
addressed since it already relies on what had been saved on it before.
Also, since this function will be used by the upcoming Launchtime
patches rename it to better reflect its intention. Note that
Launchtime is not part of what 802.1Qav specifies, but the i210
datasheet refers to this set of functionality as "Qav Transmission
Mode".
Here we also perform a tiny refactor at is_any_cbs_enabled(), and add
further documentation to igb_setup_tx_mode().
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-EOPNOTSUPP is the error value that should be reported if a flower
command is not supported by a driver. Fix it in couple of Intel drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move 10ms sleep out of function resetting TX queue.
Reset all the TX queues in one turn and
wait for all of them just once.
Use usleep_range() instead of mdelay() in order not to
affect transmission on other interfaces.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Issuing "ip link set up/down" can block TSICR interrupts, what results in
missing PTP Tx timestamp and no PPS pulse generation.
Problem happens when the link is set up with the TSICR interrupts pending.
ICR is cleared before enabling interrupts, while TSICR is not. When all TSICR
interrupts are pending at this moment, time_sync interrupt will never
be generated. TSICR should be cleared as well.
In order to reproduce the issue:
1. Setup linux with IEEE 1588 grandmaster and PPS output enabled
2. Continue setting link up/down with random intervals between commands
3. Wait until PPS is not generated ( only one pulse is generated and PPS
dies), and ptp4l complains constantly about Tx timeout.
Signed-off-by: Joanna Yurdal <jyu@trackman.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows filters added by tc-flower and specifying MAC addresses,
Ethernet types, and the VLAN priority field, to be offloaded to the
controller.
This reuses most of the infrastructure used by ethtool, but clsflower
filters are kept in a separated list, so they are invisible to
ethtool.
To setup clsflower offloading:
$ tc qdisc replace dev eth0 handle 100: parent root mqprio \
num_tc 3 map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 hw 0
(clsflower offloading depends on the netword driver to be configured
with multiple traffic classes, we use mqprio's 'num_tc' parameter to
set it to 3)
$ tc qdisc add dev eth0 ingress
Examples of filters:
$ tc filter add dev eth0 parent ffff: flower \
dst_mac aa:aa:aa:aa:aa:aa \
hw_tc 2 skip_sw
(just a simple filter filtering for the destination MAC address and
steering that traffic to queue 2)
$ tc filter add dev enp2s0 parent ffff: proto 0x22f0 flower \
src_mac cc:cc:cc:cc:cc:cc \
hw_tc 1 skip_sw
(as the i210 doesn't support steering traffic based on the source
address alone, we need to use another steering traffic, in this case
we are using the ethernet type (0x22f0) to steer traffic to queue 1)
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds basic functions needed to implement offloading for filters
created by tc-flower.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the capability of configuring the queue steering of arriving
packets based on their source and destination MAC addresses.
Source address steering (i.e. driving traffic to a specific queue),
for the i210, does not work, but filtering does (i.e. accepting
traffic based on the source address). So, trying to add a filter
specifying only a source address will be an error.
In practical terms this adds support for the following use cases,
characterized by these examples:
$ ethtool -N eth0 flow-type ether dst aa:aa:aa:aa:aa:aa action 0
(this will direct packets with destination address "aa:aa:aa:aa:aa:aa"
to the RX queue 0)
$ ethtool -N eth0 flow-type ether src 44:44:44:44:44:44 \
proto 0x22f0 action 3
(this will direct packets with source address "44:44:44:44:44:44" and
ethertype 0x22f0 to the RX queue 3)
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows igb_add_filter()/igb_erase_filter() to work on filters
that include MAC addresses (both source and destination).
For now, this only exposes the functionality, the next commit glues
ethtool into this. Later in this series, these APIs are used to allow
offloading of cls_flower filters.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect that when adding a steering filter for the local MAC
address, that all the traffic directed to that address will go to some
queue.
Currently, it's not possible to configure entries in the "in use"
state, which is the normal state of the local MAC address entry (it is
the default), this patch allows to override the steering configuration
of "in use" entries, if the filter to be added match the address and
address type (source or destination) of an existing entry.
There is a bit of a special handling for entries referring to the
local MAC address, when they are removed, only the steering
configuration is reset.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some igb models (82575 and i210) the MAC address filters can
control to which queue the packet will be assigned.
This extends the 'state' with one more state to signify that queue
selection should be enabled for that filter.
As 82575 parts are no longer easily obtained (and this was developed
against i210), only support for the i210 model is enabled.
These functions are exported and will be used in the next patch.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Makes it possible to direct packets to queues based on their source
address. Documents the expected usage of the 'flags' parameter.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will allow functionality depending on the hardware being traffic
class aware to work. In particular the tc-flower offloading checks
verifies that this bit is set.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On the RAH registers there are semantic differences on the meaning of
the "queue" parameter for traffic steering depending on the controller
model: there is the 82575 meaning, which "queue" means a RX Hardware
Queue, and the i350 meaning, where it is a reception pool.
The previous behaviour was having no effect for i210 based controllers
because the QSEL bit of the RAH register wasn't being set.
This patch separates the condition in discrete cases, so the different
handling is clearer.
Fixes: 83c21335c876 ("igb: improve MAC filter handling")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because the order of the parameters passes to 'hlist_add_behind()' was
inverted, the 'parent' node was added "behind" the 'input', as input
is not in the list, this causes the 'input' node to be lost.
Fixes: 0e71def25281 ("igb: add support of RX network flow classification")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'HWTSTAMP_TX_ON' should be handled as a value, not as a bit mask.
The modified code should behave the same, because HWTSTAMP_TX_ON is 1
and no other possible values of 'tx_type' would match the test.
However, this is more future-proof, should other values be allowed one day.
See 'struct hwtstamp_config' in 'include/uapi/linux/net_tstamp.h'
This fixes a warning reported by smatch:
igb_xmit_frame_ring() warn: bit shifter 'HWTSTAMP_TX_ON' used for logical '&'
Fixes: 26bd4e2db06be ("igb: protect TX timestamping from API misuse")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver notices that PCIe link is gone by reading 0xffffffff
from a register it clears hw->hw_addr and then calls netif_device_detach().
This happens when the PCIe device is physically unplugged for example
the user disconnected the Thunderbolt cable.
However, netif_device_detach() prevents netif_unregister() from bringing
the device down properly including tearing down MSI-X vectors. This
triggers following crash during the driver removal:
igb 0000:0b:00.0 enp11s0f0: PCIe link lost, device now detached
------------[ cut here ]------------
kernel BUG at drivers/pci/msi.c:352!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
...
Call Trace:
pci_disable_msix+0xc9/0xf0
igb_reset_interrupt_capability+0x58/0x60 [igb]
igb_remove+0x90/0x100 [igb]
pci_device_remove+0x31/0xa0
device_release_driver_internal+0x152/0x210
pci_stop_bus_device+0x78/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_bus_device+0x26/0xa0
pci_stop_bus_device+0x38/0xa0
pci_stop_and_remove_bus_device+0x9/0x20
trim_stale_devices+0xee/0x130
? _raw_spin_unlock_irqrestore+0xf/0x30
trim_stale_devices+0x8f/0x130
? _raw_spin_unlock_irqrestore+0xf/0x30
trim_stale_devices+0xa1/0x130
? get_slot_status+0x8b/0xc0
acpiphp_check_bridge.part.7+0xf9/0x140
acpiphp_hotplug_notify+0x170/0x1f0
...
To prevent the crash do not call netif_device_detach() in igb_rd32().
This should be fine because hw->hw_addr is set to NULL preventing future
hardware access of the now missing device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198181
Reported-by: Ferenc Boldog <ferenc.boldog@gmail.com>
Reported-by: Nikolay Bogoychev <nheart@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Add a per-VF value to know if a VF is trusted, by default don't
trust VFs.
* Implement netdev op to trust VFs (igb_ndo_set_vf_trust) and add
trust status to ndo_get_vf_config output.
* Allow a trusted VF to change MAC and MAC filters even if MAC
has been administratively set.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS to match the new convention..
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Credit-Based Shaper (CBS) qdisc offload
from Traffic Control system. This support enable us to leverage the
Forwarding and Queuing for Time-Sensitive Streams (FQTSS) features
from Intel i210 Ethernet Controller. FQTSS is the former 802.1Qav
standard which was merged into 802.1Q in 2014. It enables traffic
prioritization and bandwidth reservation via the Credit-Based Shaper
which is implemented in hardware by i210 controller.
The patch introduces the igb_setup_tc() function which implements the
support for CBS qdisc hardware offload in the IGB driver. CBS offload
is the only traffic control offload supported by the driver at the
moment.
FQTSS transmission mode from i210 controller is automatically enabled
by the IGB driver when the CBS is enabled for the first hardware
queue. Likewise, FQTSS mode is automatically disabled when CBS is
disabled for the last hardware queue. Changing FQTSS mode requires NIC
reset.
FQTSS feature is supported by i210 controller only.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Henrik Austad <henrik@austad.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver cannot map a TX buffer, instead of rolling back
gracefully and retrying later, we currently get a panic:
[ 159.885994] igb 0000:00:00.0: TX DMA map failed
[ 159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8
...
[ 159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8
Fix the erroneous test that leads to this situation.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The management port on an Edgecore AS7712-32 switch uses an igb MAC, but
it uses a BCM54616 PHY. Without a patch like this, loading the igb
module produces dmesg output like this:
[ 3.439125] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.439866] igb: probe of 0000:00:14.0 failed with error -2
Signed-off-by: John W Linville <linville@tuxdriver.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the PF receives a mailbox message from the VF, it grabs the mailbox
lock, reads the VF message from the mailbox, ACKs the message and drops
the lock.
While the PF is performing the action for the VF message, nothing
prevents another VF message from being posted to the mailbox. The
current code handles this condition by just dropping any new VF messages
without processing them. This results in a mailbox timeout in the VM
for posted messages waiting for an ACK, and the VF is reset by the
igbvf_watchdog_task in the VM.
Given the right sequence of VF messages and mailbox timeouts, this
condition can go on ad infinitum.
Modify the PF mailbox read method to take an 'unlock' argument that
optionally leaves the mailbox locked by the PF after reading the VF
message. This ensures another VF message is not posted to the mailbox
until after the PF has completed processing the VF message and written
its reply.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a mailbox unlock method to e1000_mbx_operations, which will be used
to unlock the PF/VF mailbox by the PF.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TSAUXC.DisableSystime is never set, so SYSTIM runs into a SYS WRAP
every 1100 secs on 80580/i350/i354 (40 bit SYSTIM) and every 35000
secs on 80576 (45 bit SYSTIM).
This wrap event sets the TSICR.SysWrap bit unconditionally.
However, checking TSIM at interrupt time shows that this event does not
actually cause the interrupt. Rather, it's just bycatch while the
actual interrupt is caused by, for instance, TSICR.TXTS.
The conclusion is that the SYS WRAP is actually expected, so the
"unexpected SYS WRAP" message is entirely bogus and just helps to
confuse users. Drop it.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the igb
driver still allowed TX packets to request HW timestamping. In this
situation, the _IGB_PTP_TX_IN_PROGRESS flag was set and would never
clear. This prevented any future HW timestamping requests to succeed.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Signed-off-by: Cliff Spradlin <cspradlin@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After add an ethertype filter, if user change the adapter speed several
times, the error "ethtool -N: etype filters are all used" is reported by
igb driver.
In older patch, function igb_nfc_filter_exit() and igb_nfc_filter_restore()
is not paried. igb_nfc_filter_restore() exist in igb_up(), but function
igb_nfc_filter_exit() is exist in __igb_close(). In the process of speed
changing, only igb_nfc_filter_restore() is called, it will take a position
of ethertype bitmap.
Reproduce steps:
Step 1: Add a etype filter by ethtool
$ethtool -N eth0 flow-type ether proto 0x88F8 action 1
Step 2: Change the adapter speed to 100M/full duplex
$ethtool -s eth0 speed 100 duplex full
Step 3: Change the adapter speed to 1000M/full duplex
ethtool -s eth0 speed 1000 duplex full
Repeat step2 and step3, then dmesg the system log, you can find the error
message, add new ethtype filter is also failed.
This fixing is move igb_nfc_filter_exit() from __igb_close() to igb_down()
to make igb_nfc_filter_restore()/igb_nfc_filter_exit() is paired.
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a few sparse warnings, these following
functions can be made static:
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_add_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_del_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_set_vf_mac_filter' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
