IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The patch 15a6af94a277 ("spi: Increase imx51 ecspi burst length based
on transfer length") increased the burst length calculation in
mx51_ecspi_prepare_transfer() to be based on the transfer length.
This breaks HW CS + SPI_CS_WORD support which was added in
6e95b23a5b2d ("spi: imx: Implement support for CS_WORD") and transfers
with bits-per-word != 8, 16, 32.
SPI_CS_WORD means the CS should be toggled after each word. The
implementation in the imx-spi driver relies on the fact that the HW CS
is toggled automatically by the controller after each burst length
number of bits. Setting the burst length to the number of bits of the
_whole_ message breaks this use case.
Further the patch 15a6af94a277 ("spi: Increase imx51 ecspi burst
length based on transfer length") claims to optimize the transfers.
But even without this patch, on modern spi-imx controllers with
"dynamic_burst = true" (imx51, imx6 and newer), the transfers are
already optimized, i.e. the burst length is dynamically adjusted in
spi_imx_push() to avoid the pause between the SPI bursts. This has
been confirmed by a scope measurement on an imx6d.
Subsequent Patches tried to fix these and other problems:
- 5f66db08cbd3 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
- e9b220aeacf1 ("spi: spi-imx: correctly configure burst length when using dma")
- c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
- cf6d79a0f576 ("spi: spi-imx: fix off-by-one in mx51 CPU mode burst length")
but the HW CS + SPI_CS_WORD use case is still broken.
To fix the problems revert the burst size calculation in
mx51_ecspi_prepare_transfer() back to the original form, before
15a6af94a277 ("spi: Increase imx51 ecspi burst length based on
transfer length") was applied.
Cc: Stefan Moring <stefan.moring@technolution.nl>
Cc: Stefan Bigler <linux@bigler.io>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Carlos Song <carlos.song@nxp.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Thorsten Scherer <T.Scherer@eckelmann.de>
Fixes: 15a6af94a277 ("spi: Increase imx51 ecspi burst length based on transfer length")
Fixes: 5f66db08cbd3 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
Fixes: e9b220aeacf1 ("spi: spi-imx: correctly configure burst length when using dma")
Fixes: c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
Fixes: cf6d79a0f576 ("spi: spi-imx: fix off-by-one in mx51 CPU mode burst length")
Link: https://lore.kernel.org/all/20240618-oxpecker-of-ideal-mastery-db59f8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Thorsten Scherer <t.scherer@eckelmann.de>
Link: https://msgid.link/r/20240618-spi-imx-fix-bustlength-v1-1-2053dd5fdf87@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
While adding a SPI device, the SPI core ensures that multiple logical CS
doesn't map to the same physical CS. For example, spi->chip_select[0] !=
spi->chip_select[1] and so forth. However, unlike the SPI master, the SPI
slave doesn't have the list of chip selects, this leads to probe failure
when the SPI controller is configured as slave. Update the
__spi_add_device() function to perform this check only if the SPI
controller is configured as master.
Fixes: 4d8ff6b0991d ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20240617153052.26636-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case usage of OCTAL mode, buswidth parameter can take the value 8.
As return value of stm32_qspi_get_mode() is used to configure fields
of CCR registers that are 2 bits only (fields IMODE, ADMODE, ADSIZE,
DMODE), clamp return value of stm32_qspi_get_mode() to 4.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Misplaced parenthesis make test of mode wrong in case mode is equal to
SPI_TX_OCTAL or SPI_RX_OCTAL.
Simplify this sanity test, if one of this bit is set, property
cs-gpio must be present in DT.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some internals of the cs35l56 can only support SPI speeds of up to
11MHz. Whilst some use-cases could support higher rates, keep things
simple by dropping the SPI speed down to this avoid any potential
issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240607103423.4159834-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The root clock is actually 49.152MHz not 40MHz, as it is derived from
the primary audio clock, update the driver to match. This error can
cause the actual clock rate to be higher than the requested clock rate
on the SPI bus.
Fixes: ef75e767167a ("spi: cs42l43: Add SPI controller support")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20240604131704.3227500-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8cc3bad9d9d6 ("spi: Remove unneded check for orig_nents")
introduced a regression: unmapped data could now be passed to the DMA
APIs, resulting in null pointer dereferences. Commit 9f788ba457b4 ("spi:
Don't mark message DMA mapped when no transfer in it is") and commit
da560097c056 ("spi: Check if transfer is mapped before calling DMA sync
APIs") addressed the problem, but only partially. Unidirectional
transactions will still result in null pointer dereference. To prevent
that from happening, assign a dummy scatterlist when no data is mapped,
so that the DMA API can be called and not result in a null pointer
dereference.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/r/8ae675b5-fcf9-4c9b-b06a-4462f70e1322@linaro.org
Reported-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Closes: https://lore.kernel.org/all/d3679496-2e4e-4a7c-97ed-f193bd53af1d@notapiano
Closes: https://lore.kernel.org/all/4748499f-789c-45a8-b50a-2dd09f4bac8c@notapiano
Fixes: 8cc3bad9d9d6 ("spi: Remove unneded check for orig_nents")
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[nfraprado: wrote the commit message]
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://msgid.link/r/20240529-dma-oops-dummy-v1-1-bb43aacfb11b@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During dummy-cycles xSPI will switch GPIO into Hi-Z mode. In that dummy
period voltage on data lines will slowly drop, what can cause
unintentional modebyte transmission. Value send to SPI memory chip will
depend on last address, and clock frequency.
To prevent unforeseen consequences of that behaviour, force send
single modebyte(0x00).
Modebyte will be send only if number of dummy-cycles is not equal
to 0. Code must also reduce dummycycle byte count by one - as one byte
is send as modebyte.
Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
Link: https://msgid.link/r/20240529074037.1345882-2-wsadowski@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
A couple of fixes to avoid calling DMA sync API when it's not needed.
This doesn't stop from discussing if IOMMU code is doing the right thing,
i.e. dereferences SG list when orig_nents == 0, but this is a separate
story.
On stm32mp157 enabling the controller before asserting CS makes the
hardware trigger spurious interrupts in a tight loop and the transfers
fail. Revert the commit that swapped the order of enable and CS. This
reintroduces the problem that swapping was supposed to fix, which
however is less grave.
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/all/39033ed7-3e57-4339-80b4-fc8919e26aa7@pengutronix.de/
Fixes: 52b62e7a5d4f ("spi: stm32: enable controller before asserting CS")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240523103326.792907-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The resent update to remove the orig_nents checks revealed
that not all DMA sync backends can cope with the unallocated
SG list, while supplying orig_nents == 0 (the commit 861370f49ce4
("iommu/dma: force bouncing if the size is not cacheline-aligned"),
for example, makes that happen for the IOMMU case). It means
we have to check if the buffers are DMA mapped before trying
to sync them. Re-introduce that check in a form of calling
->can_dma() in the same way as it's done in the DMA mapping loop
for the SPI transfers.
Reported-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/r/8ae675b5-fcf9-4c9b-b06a-4462f70e1322@linaro.org
Closes: https://lore.kernel.org/all/d3679496-2e4e-4a7c-97ed-f193bd53af1d@notapiano
Fixes: 8cc3bad9d9d6 ("spi: Remove unneded check for orig_nents")
Suggested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the DesignWare SPI controller driver supports only host mode.
However, spi2 on the Kendryte K210 SoC supports only target mode,
triggering an error message on e.g. SiPEED MAiXBiT since commit
98d75b9ef282f6b9 ("spi: dw: Drop default number of CS setting"):
dw_spi_mmio 50240000.spi: error -22: problem registering spi host
dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22
As spi2 rightfully has no "num-cs" property, num_chipselect is now zero,
causing spi_alloc_host() to fail to register the controller. Before,
the driver silently registered an SPI host controller with 4 chip
selects.
Reject target mode early on and warn the user, getting rid of the
error message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/7ae28d83bff7351f34782658ae1bb69cc731693e.1715163113.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Before ORing the new clock rate with the control register value read
from the hardware, the existing clock rate needs to be masked off as
otherwise the existing value will interfere with the new one.
CC: stable@vger.kernel.org
Fixes: 8596124c4c1b ("spi: microchip-core-qspi: Add support for microchip fpga qspi controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240508-fox-unpiloted-b97e1535627b@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
Both dma_unmap_sgtable() and sg_free_table() in spi_unmap_buf_attrs()
have checks for orig_nents against 0. No need to duplicate this.
All the same applies to other DMA mapping API calls.
Also note, there is no other user in the kernel that does this kind of
checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240507201028.564630-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
As Arnd suggested we may drop linux/spi/pxa2xx_spi.h as most of
its content is being used solely internally to SPI subsystem
(PXA2xx drivers). Hence this refactoring series with the additional
win of getting rid of legacy documentation.
Note, that we have the only user of a single plain integer field
in the entire kernel for that. Switching to software nodes does not
diminish any of type checking as we only pass an integer.
Merge series from Serge Semin <fancer.lancer@gmail.com>:
The main goal of the short series is to provide a procedure implementing
the auto-detection of the number of native Chip-Select signals supported
by the controller. The suggested algorithm is straightforward. It relies
on the fact that the SER register writable flags reflects the actual
number of available native chip-select signals. So the DW APB/AHB SSI
driver now tests the SER register for having the writable bits,
calculates the number of CS signals based on the number of set flags and
then initializes the num_cs private data field based on that, which then
will be passed to the SPI-core subsystem indicating the number of
supported hardware chip-selects. The implemented procedure will be useful
for the DW SSI device nodes not having the explicitly set "num-cs"
property. In case if the property is specified it will be utilized instead
of the auto-detection procedure.
Besides of that a small cleanup patch is introduced in the head of the
series. It converts the driver to using the BITS_TO_BYTES() macro instead
of the hard-coded DIV_ROUND_UP()-based calculation of the number of
bytes-per-transfer-word.
Now the struct chip_data is local to spi-pxa2xx.c, move
its definition to the C file. This will slightly speed up
a build and also hide badly named data type (too generic).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The timeout field is used only once and assigned to a predefined
constant. Replace all that by using the constant directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA related fields are set once and never modified. It effectively
repeats the content of the same fields in struct pxa2xx_spi_controller.
With that, remove DMA parameters from struct chip_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The documentation is referring to the legacy enumeration of the SPI
host controllers and target devices. It has nothing to do with the
modern way, which is the only supported in kernel right now. Hence,
remove outdated documentation file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no user of the linux/spi/pxa2xx_spi.h. Move its contents
to the drivers/spi/spi-pxa2xx.h.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases the number of the chip select pins might come from
the device property. Allow driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240417110334.2671228-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The modpost script is not happy
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/spi/spi-bitbang.o
because there is a missing module description.
Add it to the module.
While at it, update the terminology in Kconfig section to be in align
with added description along with the code comments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240502171518.2792895-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DW APB/AHB SSI core now supports the procedure automatically detecting the
number of native chip-select lines. Thus there is no longer point in
defaulting to four CS if the platform doesn't specify the real number
especially seeing the default number didn't correspond to any original DW
APB/AHB databook.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-5-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Number of native chip-select lines is either retrieved from the "num-cs"
DT-property or auto-detected in the generic DW APB/AHB SSI probe method.
In the former case the property is supposed to be of the "u32" size.
Convert the field type to being u32 then to be able to drop the temporary
variable afterwards.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-4-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside with the FIFO depth and DFS field size it's possible to auto-detect
a number of native chip-select synthesized in the DW APB/AHB SSI IP-core.
It can be done just by writing ones to the SER register. The number of
writable flags in the register is limited by the SSI_NUM_SLAVES IP-core
synthesize parameter. All the upper flags are read-only and wired to zero.
Based on that let's add the number of native CS auto-detection procedure
so the low-level platform drivers wouldn't need to manually set it up
unless it's required to set a constraint due to platform-specific reasons
(for instance, due to a hardware bug).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240424150657.9678-3-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit dd3e7cba1627 ("ocfs2/dlm: move BITS_TO_BYTES() to bitops.h
for wider use") there is a generic helper available to calculate a number
of bytes needed to accommodate the specified number of bits. Let's use it
instead of the hard-coded DIV_ROUND_UP() macro function.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240424150657.9678-2-fancer.lancer@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the STM32F4/7, the MOSI and CLK pins float while the controller is
disabled. CS is a regular GPIO, and therefore always driven. Currently,
the controller is enabled in the transfer_one() callback, which runs
after CS is asserted. Therefore, there is a period where the SPI pins
are floating while CS is asserted, making it possible for stray signals
to disrupt communications. An analogous problem occurs at the end of the
transfer when the controller is disabled before CS is released.
This problem can be reliably observed by enabling the pull-up (if
CPOL=0) or pull-down (if CPOL=1) on the clock pin. This will cause two
extra unintended clock edges per transfer, when the controller is
enabled and disabled.
Note that this bug is likely not present on the STM32H7, because this
driver sets the AFCNTR bit (not supported on F4/F7), which keeps the SPI
pins driven even while the controller is disabled.
Enabling/disabling the controller as part of runtime PM was suggested as
an alternative approach, but this breaks the driver on the STM32MP1 (see
[1]). The following quote from the manual may explain this:
> To restart the internal state machine properly, SPI is strongly
> suggested to be disabled and re-enabled before next transaction starts
> despite its setting is not changed.
This patch has been tested on an STM32F746 with a MAX14830 UART
expander.
[1] https://lore.kernel.org/lkml/ZXzRi_h2AMqEhMVw@dell-precision-5540/T/
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Link: https://lore.kernel.org/r/20240424135237.1329001-2-ben.wolsieffer@hefring.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Wolfram Sang <wsa+renesas@sang-engineering.com>:
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_*() functions causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
obvious and self explaining.
This is part of a tree-wide series. The rest of the patches can be found here
(some parts may still be WIP):
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux.git i2c/time_left
Because these patches are generated, I audit them before sending. This is why I
will send series step by step. Build bot is happy with these patches, though.
No functional changes intended.
Merge series from Lorenzo Bianconi <lorenzo@kernel.org>:
Introduce support for SPI-NAND driver of the Airoha NAND Flash Interface
found on Airoha ARM EN7581 SoCs.
If spi_sync() is called with the non-empty queue and the same spi_message
is then reused, the complete callback for the message remains set while
the context is cleared, leading to a null pointer dereference when the
callback is invoked from spi_finalize_current_message().
With function inlining disabled, the call stack might look like this:
_raw_spin_lock_irqsave from complete_with_flags+0x18/0x58
complete_with_flags from spi_complete+0x8/0xc
spi_complete from spi_finalize_current_message+0xec/0x184
spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474
spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230
__spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4
__spi_transfer_message_noqueue from __spi_sync+0x204/0x248
__spi_sync from spi_sync+0x24/0x3c
spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd]
mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154
_regmap_raw_read from _regmap_bus_read+0x44/0x70
_regmap_bus_read from _regmap_read+0x60/0xd8
_regmap_read from regmap_read+0x3c/0x5c
regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd]
mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd]
mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x118/0x1f4
irq_thread from kthread+0xd8/0xf4
kthread from ret_from_fork+0x14/0x28
Fix this by also setting message->complete to NULL when the transfer is
complete.
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20240430182705.13019-1-mans@mansr.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are macros spi_valid_txbuf() and spi_valid_rxbuf() for determining
if an xfer actually intended to send or receive data.
These checks were hard-coded in spi_statistics_add_transfer_stats(). We
can make use of the macros instead to make the code more readable and
more robust against potential future changes in case the definition of
what valid means changes.
The macro takes the spi_message as an argument, so we need to change
spi_statistics_add_transfer_stats() to take the spi_message as an
argument instead of the controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240430201530.2138095-3-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-9-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240430114142.28551-8-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20240430114142.28551-7-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-6-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-5-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240430114142.28551-4-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-3-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240430114142.28551-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce support for SPI-NAND driver of the Airoha NAND Flash Interface
found on Airoha ARM SoCs.
Tested-by: Rajeev Kumar <Rajeev.Kumar@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/6c9db20505b01a66807995374f2af475a23ce5b2.1714377864.git.lorenzo@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Call readl_relaxed_poll_timeout() with no sleep at the start of
cqspi_wait_for_bit(). If its short timeout expires, a sleeping
readl_relaxed_poll_timeout() call takes the relay.
The reason is to avoid hrtimer interrupts on the system. All read
operations are expected to take less than 100µs.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-3-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support reads through polling, without any IRQ. The main reason is
performance; profiling shows that the first IRQ comes quickly on our
specific hardware. Once this IRQ arrives, we poll until all data is
retrieved. Avoid initial sleep to reduce IRQ count.
Hide this behavior behind a quirk flag.
This is confirmed through micro-benchmarks, but also end-to-end
performance tests. Mobileye EyeQ5, octal flash, reading 235M on a UBIFS
filesystem:
- No optimizations, ~10.34s, ~22.7 MB/s, 199230 IRQs
- CQSPI_SLOW_SRAM, ~10.34s, ~22.7 MB/s, 70284 IRQs
- CQSPI_RD_NO_IRQ, ~9.37s, ~25.1 MB/s, 521 IRQs
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240423-cdns-qspi-mbly-v4-2-3d2a7b535ad0@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
