IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The HDMI driver was registering a single ALSA card so far with the name
vc4-hdmi.
Obviously, this is not going to work anymore when we will have multiple
HDMI controllers since we will end up trying to register two files with the
same name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e60a37444e848a384a45707a21d6df8883115f86.1599120059.git-series.maxime@cerno.tech
The audio configuration has changed for the BCM2711, with notably a
different parent clock and a different channel configuration.
Make that modular to be able to support the BCM2711.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/85a8ca721c2d800be758c55870cea98536749680.1599120059.git-series.maxime@cerno.tech
If the encoder is disabled and re-enabled (eg mode change) all infoframes
are reset, whilst the audio subsystem know nothing about this change.
The driver therefore needs to reinstate the audio infoframe for
itself.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cd579ccc2c9b9d2fce0ebaf32f847cedb0e4a7a2.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be setup at around 101% of the pixel rate. This
was done previously by setting the clock rate to 163.7MHz at probe time and
only check in mode_valid whether the mode pixel clock was under the pixel
clock +1% or not.
However, with 4k we need to change that frequency to a higher frequency
than 163.7MHz, and yet want to have the lowest clock as possible to have a
decent power saving.
Let's change that logic a bit by setting the clock rate of the HSM clock
to the pixel rate at encoder_enable time. This would work for the
BCM2711 that support 4k resolutions and has a clock that can provide it,
but we still have to take care of a 4k panel plugged on a BCM283x SoCs
that wouldn't be able to use those modes, so let's define the limit in
the variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7e692ddc231d33dd671e70ea04dd1dcf56c1ecb3.1599120059.git-series.maxime@cerno.tech
Similarly to the audio support, CEC support is not there yet for the
BCM2711, so let's skip entirely the CEC initialization through a variant
flag.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bd0c4afa83b4e121692352cdc2dd1886162c7552.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single debugfs file so far with the name
hdmi_regs.
Obviously, this is not going to work anymore when will have multiple HDMI
controllers since we will end up trying to register two files with the same
name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9505c1eb40b3ef3709277bf9e8af77917b249c32.1599120059.git-series.maxime@cerno.tech
The vc4 CRTC will use the encoder type to control its output clock
muxing. However, this will be different from HDMI0 to HDMI1, so let's
store our type in the variant structure so that we can support multiple
controllers later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2736a86b498551ba9dbc5803c5bb910627a2550c.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the timings setup in the HDMI controller
of the BCM2711 is slightly different, mostly because it supports higher
resolutions and thus needed more spaces for the various timings, resulting
in the register layout changing.
Let's add a callback for that as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0cfcbb379212f90b4abc76c0ccf3b90d1d7c0268.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the CSC setup is slightly different in
the BCM2711 than in the previous generations. Let's add a callback for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5c19bbf10153cb42ca0fb67e08606c8295c17236.1599120059.git-series.maxime@cerno.tech
The HDMI PHY in the BCM2711 HDMI controller is significantly more
complicated to setup than in the older BCM283x SoCs.
Let's add hooks to enable and disable the PHY.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7216826284dbc60a58bdacd662805d20699e5c80.1599120059.git-series.maxime@cerno.tech
The BCM2711 and BCM283x HDMI controllers use a slightly different reset
sequence, so let's add a callback to reset the controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a34bcb493da07eae58ed704f65e72ce0748e8952.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 have most of the registers
reorganized in multiple registers areas and at different offsets than
previously found.
The logic however remains pretty much the same, so it doesn't really make
sense to create a whole new driver and we should share the code as much as
possible.
Let's implement some indirection to wrap around a register and depending on
the variant will lookup the associated register on that particular variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3070236daff920e7edd11c5a72ac31fd0f6a656b.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 has a pretty different clock and
registers areas than found in the older BCM283x SoCs.
Let's create a variant structure to store the various adjustments we'll
need later on, and a function to get the resources needed for one
particular version.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/71cfa3ce3d865bbab52a0e5651bc052dc4893f11.1599120059.git-series.maxime@cerno.tech
The vc4_hdmi_connector was only used to switch between drm_connector to
drm_encoder. However, we can now use vc4_hdmi to do the switch, so that
structure is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/aee5120728db350b19c074de4290eafaf01e6671.1599120059.git-series.maxime@cerno.tech
The unbind function needs to retrieve a vc4_hdmi structure pointer through
the struct device that we're given since we want to support multiple HDMI
controllers.
However, our optional ASoC support doesn't make that trivial since it will
overwrite the device drvdata if we use it, but obviously won't if we don't
use it.
Let's make sure the fields are at the proper offset to be able to cast
between the snd_soc_card structure and the vc4_hdmi structure
transparently so we can support both cases.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/717082cba06b5c06280f26c56c08aee512365ed3.1599120059.git-series.maxime@cerno.tech
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/536ecce5898ea75839fa3788b876009d69a5ccae.1599120059.git-series.maxime@cerno.tech
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/886b955586264ce078d7d35e9b8ef9ae51675c27.1599120059.git-series.maxime@cerno.tech
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/93b418d63c876355af2b3d3afebe31a256268623.1599120059.git-series.maxime@cerno.tech
