IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
KASAN found this problem. find_first_bit() expects to look at a
pointer pointing to a long, but we look at a u32 - this is going to be
an issue with endianness but, KSAN already flags this as out-of-bounds
stack reads. This fixes it by just importing inot a local long.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218150812.68195-1-carsten.haitzler@foss.arm.com
Komeda HW can support dual-link which splits display frame to two halves
(left/link0, right/link1) and output them by two output links.
Due to the halved pixel rate of each link, the pxlclk of dual-link can be
reduced two times compare with single-link.
For enabling dual-link:
- The DT need to configure two output-links for the pipeline node.
- Komeda enable dual-link when both link0 and link1 have been connected.
Example of how the pipeline node will look like for dual-link setup
pipe0: pipeline@0 {
clocks = <&fpgaosc2>;
clock-names = "pxclk";
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
dp0_pipe0_link0: endpoint@0 {
reg = <0>;
remote-endpoint = <&dlink_connector_in0>;
};
dp0_pipe0_link1: endpoint@1 {
reg = <1>;
remote-endpoint = <&dlink_connector_in1>;
};
};
};
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618081013.13638-3-james.qian.wang@arm.com
Similar to Layer Split, but Splitter is used for writeback, which splits
the compiz result to two half parts and then feed them to two scalers.
v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
One crtc can use two komeda_pipeline, and one works as master and as
slave. the slave pipeline doesn't have its own output and timing
ctrlr, but pre-composite the input layer data flow and then feed the
result to master. the pipeline configuration like:
slave-layer-0 \
... slave->CU
slave-layer-4 / \
\
master-layer-0 --------> master->CU -> ...
... /
master-layer-4 ------>
Since komeda Compiz doesn't output alpha, so the slave->CU result
only can be used as bottom input when blend it with master input data
flows.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Komeda supports two types of layer split:
- none-scaling split
- scaling split
Since D71 merger only support scaler as input, so for none-scaling split,
the two layer dflow will be output to compiz directly. for scaling_split,
the data flow will be merged by merger firstly, then output the merged
data flow to compiz.
Komeda handles the split in kernel completely to hide the detailed and
complicated split calcualtion to user mode, for user only need to set the
layer_split property to enable/disable it.
v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Introduce a new component komeda_merger, because D71 HW supports to split
a whole image to two half parts and does the scaling independently. Merger
merges two separate results to one, and output it to compositor or wb_layer
For this patch:
- Add the definition of komeda_merger/merger_state
- Report and initialize komeda_merger according to the D71 HW.
v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Current komeda driver uses three dedicated clks for a specific purpose:
- mclk: main engine clock
- pclk: APB clock
- pipeline->aclk: AXI clock.
But per spec the komeda HW only has three input clks:
- ACLK: used for AXI masters, APB slave and most pipeline processing
- PXCLK for pipeline 0: output pixel clock for pipeline 0
- PXCLK for pipeline 1: output pixel clock for pipeline 1
So one ACLK is enough, no need to split it to three mclk/pclk/axiclk.
drop pclk/pipeline->axiclk. but only keep one mclk in komeda driver.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
This patch add the initial and necessary logic for CORE to support scaler:
- Complete the struct komeda_scaler and komeda_scaler_state for adding
the scaler specific features and capablities.
- Implement komeda_scaler_validate to check the scaler with the data flow
configurations.
- Enable scaling support for plane input path (layer input data flow).
v2: Fix a typo, and rename "needs_scaling" to "en_scaling"
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fix the kbuild test rebot reported warnings:
- symbol was not declared. Should it be static?
- missing braces around initializer
Depends on:
- https://patchwork.freedesktop.org/series/58976/
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: james qian wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Add a debugfs node "register" and entry function dump_register to
dev/pipeline/component to register dump, then user can read
"/sys/kernel/debug/komeda/register" to get the register values via these
chip function.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
[Added the d71_layer_dump() function that was in a previous commit]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
komeda_accemble_pipelines is for:
1. Verifing the component->supported_inputs according to the
pipeline->avail_components.
2. Generating component->supported_outputs.
v2: Lower the debug message of komeda_component_dump to DRM_DEBUG.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
D71 consists of a number of Register Blocks, every Block controls a
specific HW function, every block has a common block_header to represent
its type and pipeline information.
GCU (Global Control Unit) is the first Block which describe the global
information of D71 HW, Like number of block contained and the number of
pipeline supported.
So the d71_enum_resources parsed GCU and create pipeline according
the GCU configuration, and then iterate and detect the blocks that
indicated by the GCU and block_header.
And this change also added two struct d71_dev/d71_pipeline to extend
komeda_dev/komeda_pipeline to add some d71 only members.
v2:
- Return the specific errno not -1.
- Use DRM_DEBUG as default debug msg printer.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
With drmP.h removed from drm_modeset_helper.h the build of
komeda filed as reported by linux-next
Add missing include files to fix build.
For the files touched group include files and sort them.
The fix was tested on a tree with drm-misc-next merged.
And the patch was also tested to work without drm-misc-next merged.
Build tested on arm + x86.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> [linux-next]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Wang <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208221324.27002-1-sam@ravnborg.org
Parse DT and initialize corresponding dev/pipeline attributes.
Changes in v4:
- Rebase.
Changes in v3:
- Fixed style problem found by checkpatch.pl --strict.
Changes in v2:
- Unified abbreviation of "pipeline" to "pipe".
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
1. Added a brief definition of komeda_dev/pipeline/component, this change
didn't add the detailed component features and capabilities, which will
be added in the following changes.
2. Corresponding resources discovery and initialzation functions.
Changes in v4:
- Deleted unnecessary headers
Changes in v3:
- Fixed style problem found by checkpatch.pl --strict.
Changes in v2:
- Unified abbreviation of "pipeline" to "pipe".
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
