IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add toggle table related function to enhance WL throughput when WL coexist
with 4/18 HID.
The toggle table feature will toggle WL/BT priority table during WL slot,
it can decrease the impact from HID's frequently packets and prevent HID
lag.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-11-pkshih@realtek.com
Add modifications for A2DP interoperability issue of TWS earphones.
Some TWS earphones has low buffer size, so it's necessary to reduce
the slot period to let it get data more frequently.
(e.g. use 4-slot to replace the original 2-slot method).
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-10-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
Add message for debugging usage and the program flow is no change.
Add a variable reserved for WLAN firmware synchronize.
Add a group of variable to save BT packet counter, it will be
assigned as mechanism judgment in the future. Now it is just for
debug usage.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-3-pkshih@realtek.com
Add considering for different WLAN beacon interval in coexistence
mechanism.
Because the WLAN beacon period may be not 100 ms, so it's necessary
to consider any beacon period and set timer according to the interval.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-2-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Add counter to count BT info C2H command for debug usage.
It could present the C2H channel situation.
Fix BT IQK state decision condition for counting.
The original condition is wrong, it would cause coexistence mechanism
going to the wrong strategy.
New format supports getting TDMA parameter from WL firmware, since
coexistence needs current TDMA parameter to decide strategy.
Remove unnecessary operations about scoreboard, it is not a must for
current version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-8-pkshih@realtek.com
The original stop_dm flag is shared with the wifi and coexistence
mechanism internal usage, which represent two meanings, and makes
developers hard to debug.
Add a new flag manual_control for coexistence mechanism usage only.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-7-pkshih@realtek.com
This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com
Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com
Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com
BT firmware will report BLE-HID and BLE-RCU in different profile.
We can distinguish the two profile from BT info now.
Add the coexistence for BLE-HID coexistence,
it can make BLE HID work more smoothly.
BLE-HID need to Tx/Rx packet more frequently to respond
user operation, but RCU doesn't.
In the case of RCU coexistence, it will make Wi-Fi have a
higher priority to earn more Wi-Fi throughput.
If BLE-HID go for the same case,
it will make user feel mouse is lagging.
Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030055506.6560-1-pkshih@realtek.com
This patch adds a function which is able to dump firmware fifo when
firmware crashes. If firmware needs more than one time to dump all logs,
it will set a bit called "more bit" in the header of the first log, and
driver needs to set a register to inform firmware that it is ready for the
next dump.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-5-tehuang@realtek.com
Rtw88 currently has a function to dump reserved page section of the
firmware fifo. Reserved page is just part of the firmware fifo, there
are multiple sections in the firmware fifo for different usages, such as
firmware rx fifo and tx fifo.
This commit adds a function to check not only the reserved page section
but also other parts of the firmware fifo. In addition, we need to dump
firmware fifo to dump the debug log message if firmware crashes.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-4-tehuang@realtek.com
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
Previous settings for TX descriptors of and reserved page packets
are insufficient.
For the sequence number of packets downloaded to reserved page, it
should be filled by hardware.
And for ps-poll packets in reserved page, to prevent AID being
changed by hardware, NAVUSEHDR should be set.
Additionally, the rate should be adjusted based on the current band
for mgmt and reserved page packets.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-4-yhchuang@realtek.com
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips.
This patch adds the basic functions such as parameter tables, chip
information, power on flow.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b4376 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: f5df1a8b4376 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
Make objects about 8723d functions and 8723d tables,
i.e. rtw8723d.o and rtw8723d_table.o, an individual
kernel module called rtw88_8723d.ko.
For 8723d pcie chip, i.e. 8723DE chip, add a chip
entry point module called rtw88_8723de.ko which
will depend on rtw88_8723d.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-6-yhchuang@realtek.com
Make objects about 8822b functions and 8822b tables,
i.e. rtw8822b.o and rtw8822b_table.o, an individual
kernel module called rtw88_8822b.ko.
For 8822b pcie chip, i.e. 8822BE chip, add a chip
entry point module called rtw88_8822be.ko which
will depend on rtw88_8822b.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-5-yhchuang@realtek.com
Make objects about 8822c functions and 8822c tables,
i.e. rtw8822c.o and rtw8822c_table.o, an individual
kernel module called rtw88_8822c.ko.
For 8822c pcie chip, i.e. 8822CE chip, add a chip
entry point module called rtw88_8822ce.ko which
will depend on rtw88_8822c.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-4-yhchuang@realtek.com
Since 8723D use different address of ltecoex register, this commit add a
new field in chip_info and fill proper address. Then, ltecoex_read_reg()
and ltecoex_reg_write() can use them to access ltecoex according to chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-7-yhchuang@realtek.com
Flush queue is used to check if queue is empty, before doing something
else. Since 8723D uses different registers and page number of
availabl/reserved occupy 8 bits instead of 16 bits, so use a 'wsize' field
to discriminate which rtw_read{8,16} is adopted.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-6-yhchuang@realtek.com
Without this patch, wifi card can't initialize properly due to BT in USB
suspend state. So, we disable BT USB suspend (wakeup) in shutdown callback
that is the moment before rebooting. To save BT USB power, we can't do this
in 'remove' callback.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-5-yhchuang@realtek.com
When chip's temperature is changed, RF characters are changed. To keep the
characters to be consistent, 8723d uses thermal meter to assist in
calibrating LCK, IQK, crystal and TX power.
A base thermal value is programmed in efuse, all calibration data in
MP process is based on this thermal value. So we calucate the delta of
thermal value between the base value, and use this delta to reference XTAL
and TX power offset tables to know how much we need to adjust.
For IQK and LCK, driver checks if delta of thermal value is over 8, then
they are triggered.
For crystal adjustment, when delta of thermal value is changed, we check
XTAL tables to get offset of XTAL value. If thermal value is larger than
base value, positive table (_p as suffix) is used. Otherwise, we use
negative table (_n as suffix). Then, we add offset to XTAL default value
programmed in efuse, and write sum value to register.
To compensate TX power, there are two hierarchical tables. First level use
delta of thermal value to access eight tables to yield delta of TX power
index. Then, plus base TX power index to get index of BB swing table
(second level tables) where register value is induced.
BB swing table can't deal with all cases, if index of BB swing table is
over the size of the table. In this case, TX AGC is used to compensate the
remnant part. Assume 'upper' is the upper bound of BB swing table, and
'target' is the desired index. Then, we can illustrate them as
compensation method BB swing TX AGC
------------------- -------- --------------
target > upper upper target - upper
target < 0 0 target
otherwise target 0
For debug purpose, add a column 'rem' to tx_pwr_tbl entry, and it looks
like
path rate pwr base (byr lmt ) rem
A CCK_1M 32(0x20) 34 -2 ( 0 -2) 0
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-4-yhchuang@realtek.com
IQ calibration is used to calibrate RF characteristic to yield expected
performance. Basically, we do calibration twice and compare the similarity
to determine calibration is good or not, if not we do the third
calibration, and then compare with the results of first and second
calibration. If it still not similar, IQK is failed.
Before doing calibration, we need to backup registers that will be
modified in calibration procedure, and restore these registers after
calibration is done.
A calibration procedure can divided into four sub-procedures that are
S1-TX, S1-RX, S0-TX and S0-RX. Where, S1 and S0 represent to path A and B
respectively. Each sub-procedure configure proper registers, and then
rigger one-shot calibration and poll until completion. For RX calibration,
it needs to do twice one-shot calibration, first one is to yield parameter
used by second one.
The result of TX part is stored for TX power tracking that adjusts TX AGC
to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-3-yhchuang@realtek.com
LC calibration is done by hardware circuit. Driver sets the LCK bit to kick
start, and then poll the bit to check if it's done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-2-yhchuang@realtek.com
DIG sets only one IG register for most chips, but 8723D need to set
additional register for CCK rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-8-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
Update RTL8822C devices' phy tables to v50.
The new parameters introduces new RFE type 5 for some new modules.
Also added a new regulatory CN for power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424073812.26896-1-yhchuang@realtek.com
Implement rtw_chip_ops::phy_set_param and ::mac_init to initialize
mac/bb/rf, and they are used during interface up. The procedure contains
power on sequence registers, download firmware, load predefined parameters,
mac/bb/rf specific register and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-9-yhchuang@realtek.com
The WLAN CPU of 8723D device is different from others, add legacy
firmware download function for it. A new variable wlan_cpu is used to
decide which firmware download function we should use.
Legacy firmware file contains 32 bytes header including version and
subversion. When downloading to wlan cpu, header is excluded.
Firmware is downloaded via beacon queue to reserved page that is a part of
TX buffer. Since 11N WLAN CPU uses different control registers, this patch
introduces related control registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
8723D devices need to grant efuse access before dumping physical efuse
map, other chips don't need it, so keep this ops as blank.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-8-yhchuang@realtek.com
8723D use SIPI to indirectly read RF register instead of directly read,
so introduce a new struct rtw_rf_sipi_addr and new function
rtw_phy_read_rf_sipi(). Since other chips don't use the new function,
only 8723D needs to fill struct rtw_rf_sipi_addr in rtw_chip_info.
Because there are two kinds of functions for reading RF registers now,
change rtw_phy_read_rf() to chip->ops->read_rf() in
rtw_phy_write_rf_reg_sipi() so that we can switch tp proper RF read
functions depends on the type of the chip.
Though 8723D is an 1x1 chip, it has two RF PHY and we can switch to
one of them, and that should be configured properly. Hence, add a
fix_rf_phy_num to struct rtw_chip_info to allow driver to set one of
the PHY's registers for 8723D, even it is only 1x1. Another variable
rf_phy_num is introduced to keep the constraint number of RF path we
can access, and its value is:
rf_phy_num = (fix_rf_phy_num ? fix_rf_phy_num : rf_path_num)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-5-yhchuang@realtek.com
RTL8723DE is an 11n 1x1 2.4G single band chip with the
following capabilities:
- TX/RX BD size: 16/8
- TX/RX desc size: 40/24
- physical/logical/protected efuse size: 512/512/96
- TX gain index factor: 1
- max TX power index: 0x3F
- band: 2G
- HT: support
- VHT: Not support
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-2-yhchuang@realtek.com
To support ieee80211_ops::set_antenna, the driver can decide if the
antenna mask is accepted, otherwise it can return an error code.
Because each chip could have different limitations, let the chip
check the mask and return.
Also the antenna mask for TRX from upper space is 32-bit long.
Change the antenna mask for rtw_chip_ops::set_antenna from u8 to u32.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410100950.3199-2-yhchuang@realtek.com
In previous setting, management packets' sequence numbers will
not increase and always stay at 0. Add hw sequence number support
for mgmt packets.
The table below shows different sequence number setting in the
tx descriptor.
seq num ctrl | EN_HWSEQ | DISQSELSEL | HW_SSN_SEL
------------------------------------------------------
sw ctrl | 0 | N/A | N/A
hw ctrl per MACID | 1 | 0 | N/A
hw ctrl per HWREG | 1 | 1 |HWREG(0/1/2/3)
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200326020408.25218-1-yhchuang@realtek.com
Add a new entry "coex_info" in debugfs to dump coex's states for
us to debug on coex's issues.
The basic concept for co-existence (coex, usually for WiFi + BT)
is to decide a strategy based on the current status of WiFi and
BT. So, it means the WiFi driver requires to gather information
from BT side and choose a strategy (TDMA/table/HW settings).
Althrough we can easily check the current status of WiFi, e.g.,
from kernel log or just dump the hardware registers, it is still
very difficult for us to gather so many different types of WiFi
states (such as RFE config, antenna, channel/band, TRX, Power
save). Also we will need BT's information that is stored in
"struct rtw_coex". So it is necessary for us to have a debugfs
that can dump all of the WiFi/BT information required.
Note that to debug on coex related issues, we usually need a
longer period of time of coex_info dump every 2 seconds (for
example, 30 secs, so we should have 15 times of coex_info's
dump).
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200313033008.20070-2-yhchuang@realtek.com
Each device has only one reserved page shared with all of the
vifs, so it seems not reasonable to pass vif as one of the
arguments to rtw_fw_download_rsvd_page(). If driver is going
to run more than one vif, the content of reserved page could
not be built for all of the vifs.
To fix it, let each vif maintain its own reserved page list,
and build the final reserved page to download to the firmware
from all of the vifs. Hence driver should add reserved pages
to each vif according to the vif->type when adding the vif.
For station mode, add reserved page with rtw_add_rsvd_page_sta().
If the station mode is going to suspend in PNO (net-detect)
mode, remove the reserved pages used for normal mode, and add
new one for wowlan mode with rtw_add_rsvd_page_pno().
For beacon mode, only beacon is required to be added using
rtw_add_rsvd_page_bcn().
This would make the code flow simpler as we don't need to
add reserved pages when vif is running, just add/remove them
when ieee80211_ops::[add|remove]_interface.
When driver is going to download the reserved page, it will
collect pages from all of the vifs, this list is maintained
by rtwdev, with build_list as the pages' member. That way, we
can still build a list of reserved pages to be downloaded.
Also we can get the location of the pages from the list that
is maintained by rtwdev.
The biggest problem is that the first page should always be
beacon, if other type of reserved page is put in the first
page, the tx descriptor and offset could be wrong.
But station mode vif does not add beacon into its list, so
we need to add a dummy page in front of the list, to make
sure other pages will not be put in the first page. As the
dummy page is allocated when building the list, we must free
it before building a new list of reserved pages to firmware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-4-yhchuang@realtek.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225002746.GA26789@embeddedor
Remove unused fab_version member from struct rtw_hal.
Some of the checks being made were nonsense.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware value of secondary channel offset isn't very intuitive. This
commit adds enumeration, so we can easier to check the logic with the
suffix of enumeration name, likes _UPPER or _LOWER.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As driver can easily get vif with container_of(), we can
just remove it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
