IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently, the driver probes just fine and binds all its resources even
if the physical device is not present.
As the device lacks an identification register, let's at least read the
LSR register to check whether a device at the configured address responds
to the request at all.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-7-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the interrupt line is shared with other devices, the IRQ must be
level-triggered, as only one device can trigger a falling edge. To support
this, try to acquire the IRQ with IRQF_TRIGGER_LOW|IRQF_SHARED first.
Interrupt controllers that lack support for level-triggers will return an
error, in which case the driver will now retry the acqusition with
IRQF_TRIGGER_FALLING, which was also the default before.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-6-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a threaded IRQ handler to get rid of the irq_work kthread.
This also allows for the driver to use interrupts generated by
a threaded controller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-5-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently only uses IRQF_TRIGGER_FALLING if the probing
happened without a device-tree setup. The device however will always
generate falling edges on its IRQ line, so let's use that flag in
all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-4-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the length is zero then the print_hex_dump_bytes won't output
anything, so testing the length before the call is unnecessary.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-2-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to display console messages in low power mode, console pins
must be kept active after suspend call.
Initial patch "serial: stm32: add support for no_console_suspend" was part
of "STM32 usart power improvement" series, but as dependancy to
console_suspend pinctl state has been removed to fit with Rob comment [1],
this patch has no more dependancy with any other patch of this series.
[1] https://lkml.org/lkml/2019/7/9/451
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200519094104.27082-1-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable kgdb to debug the early parts of the kernel.
Unfortunately kgdb normally is a client of the tty API in the kernel
and serial drivers don't register to the tty layer until fairly late
in the boot process.
Serial drivers do, however, commonly register a boot console. Let's
enable the kgdboc driver to work with boot consoles to provide early
debugging.
This change co-opts the existing read() function pointer that's part
of "struct console". It's assumed that if a boot console (with the
flag CON_BOOT) has implemented read() that both the read() and write()
function are polling functions. That means they work without
interrupts and read() will return immediately (with 0 bytes read) if
there's nothing to read. This should be a safe assumption since it
appears that no current boot consoles implement read() right now and
there seems no reason to do so unless they wanted to support
"kgdboc_earlycon".
The normal/expected way to make all this work is to use
"kgdboc_earlycon" and "kgdboc" together. You should point them both
to the same physical serial connection. At boot time, as the system
transitions from the boot console to the normal console (and registers
a tty), kgdb will switch over.
One awkward part of all this, though, is that there can be a window
where the boot console goes away and we can't quite transtion over to
the main kgdboc that uses the tty layer. There are two main problems:
1. The act of registering the tty doesn't cause any call into kgdboc
so there is a window of time when the tty is there but kgdboc's
init code hasn't been called so we can't transition to it.
2. On some serial drivers the normal console inits (and replaces the
boot console) quite early in the system. Presumably these drivers
were coded up before earlycon worked as well as it does today and
probably they don't need to do this anymore, but it causes us
problems nontheless.
Problem #1 is not too big of a deal somewhat due to the luck of probe
ordering. kgdboc is last in the tty/serial/Makefile so its probe gets
right after all other tty devices. It's not fun to rely on this, but
it does work for the most part.
Problem #2 is a big deal, but only for some serial drivers. Other
serial drivers end up registering the console (which gets rid of the
boot console) and tty at nearly the same time.
The way we'll deal with the window when the system has stopped using
the boot console and the time when we're setup using the tty is to
keep using the boot console. This may sound surprising, but it has
been found to work well in practice. If it doesn't work, it shouldn't
be too hard for a given serial driver to make it keep working.
Specifically, it's expected that the read()/write() function provided
in the boot console should be the same (or nearly the same) as the
normal kgdb polling functions. That means continuing to use them
should work just fine. To make things even more likely to work work
we'll also trap the recently added exit() function in the boot console
we're using and delay any calls to it until we're all done with the
boot console.
NOTE: there could be ways to use all this in weird / unexpected ways.
If you do something like this, it's a bit of a buyer beware situation.
Specifically:
- If you specify only "kgdboc_earlycon" but not "kgdboc" then
(depending on your serial driver) things will probably work OK, but
you'll get a warning printed the first time you use kgdb after the
boot console is gone. You'd only be able to do this, of course, if
the serial driver you're running atop provided an early boot console.
- If your "kgdboc_earlycon" and "kgdboc" devices are not the same
device things should work OK, but it'll be your job to switch over
which device you're monitoring (including figuring out how to switch
over gdb in-flight if you're using it).
When trying to enable "kgdboc_earlycon" it should be noted that the
names that are registered through the boot console layer and the tty
layer are not the same for the same port. For example when debugging
on one board I'd need to pass "kgdboc_earlycon=qcom_geni
kgdboc=ttyMSM0" to enable things properly. Since digging up the boot
console name is a pain and there will rarely be more than one boot
console enabled, you can provide the "kgdboc_earlycon" parameter
without specifying the name of the boot console. In this case we'll
just pick the first boot that implements read() that we find.
This new "kgdboc_earlycon" parameter should be contrasted to the
existing "ekgdboc" parameter. While both provide a way to debug very
early, the usage and mechanisms are quite different. Specifically
"kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and
there is a transition from one to the other. The "ekgdboc" parameter,
on the other hand, replaces the "kgdboc" parameter. It runs the same
logic as the "kgdboc" parameter but just relies on your TTY driver
being present super early. The only known usage of the old "ekgdboc"
parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should
be noted that "kbd" has special treatment allowing it to init early as
a tty device.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This file is only ever compiled if that config is on since the
Makefile says:
obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
Let's get rid of the useless #ifdef.
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.7.Icb528f03d0026d957e60f537aa711ada6fd219dc@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This reverts commit 81eaadcae81b4c1bf01649a3053d1f54e2d81cf1.
Commit 81eaadcae81b ("kgdboc: disable the console lock when in kgdb")
is no longer needed now that we have the patch ("kgdb: Disable
WARN_CONSOLE_UNLOCKED for all kgdb"). Revert it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.2.I02258eee1497e55bcbe8dc477de90369c7c7c2c5@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d0815b ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user is not supposed to thinker with the underlying sysrq_key_op.
Make that explicit by adding a handful of const notations.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-2-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export a pointer to the sysrq_get_key_op(). This way we can cleanly
unregister it, instead of the current solutions of modifuing it inplace.
Since __sysrq_get_key_op() is no longer used externally, let's make it
a static function.
This patch will allow us to limit access to each and every sysrq op and
constify the sysrq handling.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-1-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No other functions use the return value of mxser_change_speed() and the
return value is always 0 now. Make it return void. This fixes the
following coccicheck warning:
drivers/tty/mxser.c:645:5-8: Unneeded variable: "ret". Return "0" on
line 650
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200506061735.19369-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf14 ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.
Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace contents of EXAR_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512140252.67631-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe.
In discussion on the mailing list, it has been determined that this is
not the correct type of fix for this issue. Revert it so that we can do
this correctly.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Cc: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXrVmRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymY+ACfelBeBAxlYjuvZ8QpDYSkR9fl8EIAoKeuJocX
TaXtUFCvCSax68siL81w
=L0Rp
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues"
* tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xilinx_uartps: Fix missing id assignment to the console
vt: fix unicode console freeing with a common interface
Revert "tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart"
Support 32-bit access for the TX/RX hold registers UTXH and URXH.
This is required for some newer SoCs.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-3-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the name of macro for general usage.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-1-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9231e69831551da3a78a618b31702ea4dedd5e
Rajendra writes:
Greg, there are other patches in the series which have a
dependency on this patch [1] would it be possible for you to
drop this patch and instead ack it so it can be taken via the
msm tree?
So dropping it from here.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1588507469-31889-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a28e ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a28e ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By directly using kfree() in different places we risk missing one if
it is switched to using vfree(), especially if the corresponding
vmalloc() is hidden away within a common abstraction.
Oh wait, that's exactly what happened here.
So let's fix this by creating a common abstraction for the free case
as well.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-by: syzbot+0bfda3ade1ee9288a1be@syzkaller.appspotmail.com
Fixes: 9a98e7a80f95 ("vt: don't use kmalloc() for the unicode screen buffer")
Cc: <stable@vger.kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2005021043110.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 580d952e44de5509c69c8f9346180ecaa78ebeec ("tty:
serial: bcm63xx: fix missing clk_put() in bcm63xx_uart") because we
should not be doing a clk_put() if we were not successful in getting a
valid clock reference via clk_get() in the first place.
Fixes: 580d952e44de ("tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200501013904.1394-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains a handful of fixes that I'd like to target for 5.7.
Specifically:
* The change of a linker argument to allow linking with lld.
* A build fix for configurations without a frame pointer.
* A handful of build fixes related the SBI 0.1 vs 0.2 split.
* The removal of STRICT_KERNEL_RWX for !MMU, which isn't useful
-----BEGIN PGP SIGNATURE-----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=MtxP
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes.
Specifically:
- fix linker argument to allow linking with lld
- build fix for configurations without a frame pointer
- a handful of build fixes related the SBI 0.1 vs 0.2 split
- remove STRICT_KERNEL_RWX for !MMU, which isn't useful"
* tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: select ARCH_HAS_STRICT_KERNEL_RWX only if MMU
riscv: sbi: Fix undefined reference to sbi_shutdown
tty: riscv: Using RISCV_SBI_V01 instead of RISCV_SBI
riscv: sbi: Correct sbi_shutdown() and sbi_clear_ipi() export
riscv: fix vdso build with lld
RISC-V: stacktrace: Declare sp_in_global outside ifdef
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200427122415.47416-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No users of hvcs_driver_string, remove it. This fixes the following gcc
warning:
drivers/tty/hvc/hvcs.c:199:19: warning: ‘hvcs_driver_string’ defined but
not used [-Wunused-const-variable=]
static const char hvcs_driver_string[]
^~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200403071325.3721-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the following messages are seen when booting i.MX8QXP:
fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)
It is not really useful to have such messages on every boot, so change
them to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
