IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch enables the MAX77686 PMIC drivers in the multi_v7_defconfig used
on exynos4412-prime family of SoCs [1]. The exynos4412-prime based boards
are producing the following runtime errors only on the multi_v7_defconfig [2]:
kern.err: deviceless supply vdd_arm not found, using dummy regulator
kern.err: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage to 1287500
kern.err: cpufreq: __target_index: Failed to change cpu frequency: -22
I reviewed the exynos_defconfig, which does not produce these runtime
errors. It was obvious that the exynos_defconfig has the PMIC drivers
enabled, whereas the multi_v7_defconfig does not. This patch has been tested
on a odroid-u2 and a odroid-u3 board. It has resolved the runtime errors.
Therefore, I purpose we enabled these drivers in the multi_v7_defconfig.
[1] http://www.hardkernel.com/main/products/prdt_info.php?g_code=G135270682824
[2] http://storage.armcloud.us/kernel-ci/mainline/v3.18-rc7-48-g7cc78f8/arm-multi_v7_defconfig/lab-tbaker-00/boot-exynos4412-odroidu3.html
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The existing MCE code calls flush_tlb hook with IS=0 (single page) resulting
in partial invalidation of TLBs which is not right. This patch fixes
that by passing IS=0xc00 to invalidate whole TLB for successful recovery
from TLB and ERAT errors.
Cc: stable@vger.kernel.org
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
upatepp can get called for a nohpte fault when we find from the linux
page table that the translation was hashed before. In that case
we are sure that there is no existing translation, hence we could
avoid doing tlbie.
We could possibly race with a parallel fault filling the TLB. But
that should be ok because updatepp is only ever relaxing permissions.
We also look at linux pte permission bits when filling hash pte
permission bits. We also hold the linux pte busy bits while
inserting/updating a hashpte entry, hence a paralle update of
linux pte is not possible. On the other hand mprotect involves
ptep_modify_prot_start which cause a hpte invalidate and not updatepp.
Performance number:
We use randbox_access_bench written by Anton.
Kernel with THP disabled and smaller hash page table size.
86.60% random_access_b [kernel.kallsyms] [k] .native_hpte_updatepp
2.10% random_access_b random_access_bench [.] doit
1.99% random_access_b [kernel.kallsyms] [k] .do_raw_spin_lock
1.85% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
1.26% random_access_b [kernel.kallsyms] [k] .native_flush_hash_range
1.18% random_access_b [kernel.kallsyms] [k] .__delay
0.69% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
0.37% random_access_b [kernel.kallsyms] [k] .clear_user_page
0.34% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
0.32% random_access_b [kernel.kallsyms] [k] fast_exception_return
0.30% random_access_b [kernel.kallsyms] [k] .hash_page_mm
With Fix:
27.54% random_access_b random_access_bench [.] doit
22.90% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
5.76% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
5.20% random_access_b [kernel.kallsyms] [k] fast_exception_return
5.12% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
4.80% random_access_b [kernel.kallsyms] [k] .hash_page_mm
3.31% random_access_b [kernel.kallsyms] [k] data_access_common
1.84% random_access_b [kernel.kallsyms] [k] .trace_hardirqs_on_caller
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- removal of now dead code and AT91-specific driver
- removal of !DT initialization in some core AT91 drivers
- simplification of Kconfig DT board file selection: now automatic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUgJyWAAoJEAf03oE53VmQ/o0IAK56Q3+fTgTi5uT5RwvYpFI+
U3Zosn6UNe2kxNpJMtsaWM7vCrmMdHb6LPaf4dy66e4tL4sBhYmyXhWU9UTEiwtw
l3Y5QCVqOpOKtVc/cYOtYtHYkcHyqyVa0qRb3XITvwpUeG0iJxrtcMRYTlDUpKD4
pJEfRK2CcHUrNXnnOcHkYaj0d5dXlJ2wJeGiAkCI0iuVWh4f44ipOAPI/0vZLO39
OIFBZRwXmQpWwncLlbVrwScK7ZD8I/qersrH72c3RdIBp0K6tbuNSXkLFL7pZhp0
pJ1Yh44HLmAklx4G0Ui0h4fWu5wMCrT7YBUXZ3Jv+RTRwW1Sr9pAhZdGxXtAYXo=
=CEE6
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup5' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/cleanup
Pull "Fifth batch of cleanup/SoC for 3.19" from Nicolas Ferre:
- removal of now dead code and AT91-specific driver
- removal of !DT initialization in some core AT91 drivers
- simplification of Kconfig DT board file selection: now automatic
* tag 'at91-cleanup5' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUgI0MAAoJEAf03oE53VmQauEH/38kPqGBa4Me4pBhvA9xMsDH
8cCuJ3Mpo14NiEADu56QY5dG5qnVfA1F0Mn+Xs/1iR8b9TQPoHIs7D8BO25Yb8vJ
KdkeIfUBgFl8GV8W6QfABRf6Mr2aidVknBNBE/hsUStDkU3hNU0i3p/kn87f/QH8
SuFXao18pqqQJ+pVigMRyEWbfGXYYUcJoKQYg8Us/LNHLP4Zl3PSerqAhPnvjts6
QrQvT6t4ijCixvLs8/baEwFNylUWarRbziVh6GPmzBrOl8KL93NPwnGXcCbE9zXS
tVjcXYgRcq9h7rUp83AqxnxWPbKdJnD3S91huwhikZirt7+CcgulAbe5BLYcnnE=
=FZRZ
-----END PGP SIGNATURE-----
Merge tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
Pull "First batch of defconfigs for AT91 / 3.19:" from Nicolas Ferre:
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
commit 68a3c0433077 ([media] ARM: OMAP2: RX-51: update
si4713 platform data) updated board-rx51-peripherals.c
so that si4713 could be easily used on DT boot, but
it ended up introducing a build warning whenever
si4713 isn't enabled.
This patches fixes that warning:
arch/arm/mach-omap2/board-rx51-peripherals.c:1000:36: warning: \
‘rx51_si4713_platform_data’ defined but not used [-Wunused-variable]
static struct si4713_platform_data rx51_si4713_platform_data = {
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUffEUAAoJEPOmecmc0R2Bk4QH/0O8+misF7MM3/EX0UOicb09
zrrVaPfH8GKHz3NlXGNZhIgy1coNoElBmdWPEb+XI+tRI3vKcyHtsJp78XHYupBl
yHFXjRYw4dHwwc08cQRDzf8qfWFpTnKX/gSBhgn5+kuIvylalLmnY8RjYtuQcaYW
DEc5B8eEMmmDH1Y3UBat+JOIJZY4NWxc9zmK+wRuMtcLt8ieCmgOWVMBjl8BerAe
Vdi0EM3YicA/HDzPVNq3xQK6cUtWDfKSFvkJhwc9Q40Yl4LQaOf2YMA2sZ/4+Qnl
F1LLJtJFMo9A0vECDJIfleXJRXnq0VjVp1Mn18Do8J6zsazzS94ppSDyk5EliVg=
=jMaL
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "last dts changes for 3.19" from Jason Cooper:
- rk3288 thermal driver that got accepted into the thermal tree
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
* tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: dts: rockchip: enable thermal on rk3288-evb board
ARM: dts: rockchip: add main thermal info to rk3288
ARM: dts: rockchip: add RK3288 Thermal data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the selection of the new PWM driver using TC Blocks. This driver is
useful so we enable it in both sama5 and at91_dt defconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the Atmel eXtended DMA Controller driver option. This driver is first used
on SAMA5D4 SoCs and only relevant in sama5_defconfig file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add neon support for sama5d4 and large blocks/files support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adjusts the registration of the cpufreq-dt driver in the
mvebu platform to indicate to the cpufreq driver that the platform has
independent clocks for each CPU.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=R4je
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "ARM: tegra: IOMMU support for v3.19" from Thierry Reding:
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
* tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since PCIe is using SMMUv1 which only supports 15-bit stream ID,
only 7-bit PCI bus id is used to specify stream ID. Therefore,
we only limit the PCI bus range to 0x7f.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Armada 370/XP suspend/resume support
- mvebu SoC driver suspend/resume support
- irqchip
- clocksource
- mbus
- clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uX+e
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-suspend-3.19' of git://git.infradead.org/linux-mvebu into next/soc
Pull "mvebu SoC suspend changes for v3.19" from Jason Cooper:
- Armada 370/XP suspend/resume support
- mvebu SoC driver suspend/resume support
- irqchip
- clocksource
- mbus
- clk
* tag 'mvebu-soc-suspend-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
Documentation: dt-bindings: minimal documentation for MVEBU SDRAM controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a squash of several imx_v6_v7_defconfig update patches.
- Enable tlv320aic3x audio codec by default (Phytec PBAB01 board)
- Enable DS1307 rtc and gpio fan by default (TBS2910 board)
- Select thermal related drivers
- Add SNVS power off driver
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When hardware supports APIC/x2APIC virtualization we don't need to use
pirqs for MSI handling and instead use APIC since most APIC accesses
(MMIO or MSR) will now be processed without VMEXITs.
As an example, netperf on the original code produces this profile
(collected wih 'xentrace -e 0x0008ffff -T 5'):
342 cpu_change
260 CPUID
34638 HLT
64067 INJ_VIRQ
28374 INTR
82733 INTR_WINDOW
10 NPF
24337 TRAP
370610 vlapic_accept_pic_intr
307528 VMENTRY
307527 VMEXIT
140998 VMMCALL
127 wrap_buffer
After applying this patch the same test shows
230 cpu_change
260 CPUID
36542 HLT
174 INJ_VIRQ
27250 INTR
222 INTR_WINDOW
20 NPF
24999 TRAP
381812 vlapic_accept_pic_intr
166480 VMENTRY
166479 VMEXIT
77208 VMMCALL
81 wrap_buffer
ApacheBench results (ab -n 10000 -c 200) improve by about 10%
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the hardware supports APIC virtualization we may decide not to use
pirqs and instead use APIC/x2APIC directly, meaning that we don't want
to set x86_msi.setup_msi_irqs and x86_msi.teardown_msi_irq to
Xen-specific routines. However, x2APIC is not set up by the time
pci_xen_hvm_init() is called so we need to postpone setting these ops
until later, when we know which APIC mode is used.
(Note that currently x2APIC is never initialized on HVM guests. This
may change in the future)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Introduce support for new hypercall GNTTABOP_cache_flush.
Use it to perform cache flashing on pages used for dma when necessary.
If GNTTABOP_cache_flush is supported by the hypervisor, we don't need to
bounce dma map operations that involve foreign grants and non-coherent
devices.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Introduce an arch specific function to find out whether a particular dma
mapping operation needs to bounce on the swiotlb buffer.
On ARM and ARM64, if the page involved is a foreign page and the device
is not coherent, we need to bounce because at unmap time we cannot
execute any required cache maintenance operations (we don't know how to
find the pfn from the mfn).
No change of behaviour for x86.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge xen/mm32.c into xen/mm.c.
As a consequence the code gets compiled on arm64 too.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
In xen_dma_map_page, if the page is a local page, call the native
map_page dma_ops. If the page is foreign, call __xen_dma_map_page that
issues any required cache maintenane operations via hypercall.
The reason for doing this is that the native dma_ops map_page could
allocate buffers than need to be freed. If the page is foreign we don't
call the native unmap_page dma_ops function, resulting in a memory leak.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
dev_addr is the machine address of the page.
The new parameter can be used by the ARM and ARM64 implementations of
xen_dma_map_page to find out if the page is a local page (pfn == mfn) or
a foreign page (pfn != mfn).
dev_addr could be retrieved again from the physical address, using
pfn_to_mfn, but it requires accessing an rbtree. Since we already have
the dev_addr in our hands at the call site there is no need to get the
mfn twice.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Use is_device_dma_coherent to check whether we need to issue cache
maintenance operations rather than checking on the existence of a
particular dma_ops function for the device.
This is correct because coherent devices don't need cache maintenance
operations - arm_coherent_dma_ops does not set the hooks that we
were previously checking for existance.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Introduce a boolean flag and an accessor function to check whether a
device is dma_coherent. Set the flag from set_arch_dma_coherent_ops.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Introduce a boolean flag and an accessor function to check whether a
device is dma_coherent. Set the flag from set_arch_dma_coherent_ops.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Remove code duplication in mm32.c by calling the native dma_ops if the
page is a local page (not a foreign page). Use a simple pfn_valid(pfn)
check to figure out if the page is local, exploiting the fact that dom0
is mapped 1:1, therefore pfn_valid always returns false when called on a
foreign mfn.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Dom0 is not actually capable of issuing outer_inv_range or
outer_clean_range calls.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
The feature has been removed from Xen. Also Linux cannot use it on ARM32
without CONFIG_ARM_LPAE.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Currently the kernel patches all necessary instructions once at boot
time, so modules are not covered by this.
Change the apply_alternatives() function to take a beginning and an
end pointer and introduce a new variant (apply_alternatives_all()) to
cover the existing use case for the static kernel image section.
Add a module_finalize() function to arm64 to check for an
alternatives section in a module and patch only the instructions from
that specific area.
Since that module code is not touched before the module
initialization has ended, we don't need to halt the machine before
doing the patching in the module's code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If the overflow threshold for a counter is set above or near the
0xffffffff boundary then the kernel may lose track of the overflow
causing only events that occur *after* the overflow to be recorded.
Specifically the problem occurs when the value of the performance counter
overtakes its original programmed value due to wrap around.
Typical solutions to this problem are either to avoid programming in
values likely to be overtaken or to treat the overflow bit as the 33rd
bit of the counter.
Its somewhat fiddly to refactor the code to correctly handle the 33rd bit
during irqsave sections (context switches for example) so instead we take
the simpler approach of avoiding values likely to be overtaken.
We set the limit to half of max_period because this matches the limit
imposed in __hw_perf_event_init(). This causes a doubling of the interrupt
rate for large threshold values, however even with a very fast counter
ticking at 4GHz the interrupt rate would only be ~1Hz.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If I include asm/irq.h on the top of my code, and set ARCH=arm64,
I'll get a compile warning, details are below:
warning: ‘struct pt_regs’
declared inside parameter list [enabled by default]
This patch is suggested by Arnd, see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-December/308270.html
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Building arm64.allmodconfig leads to the following warning:
usb/gadget/function/f_ncm.c:203:0: warning: "NCAPS" redefined
#define NCAPS (USB_CDC_NCM_NCAP_ETH_FILTER | USB_CDC_NCM_NCAP_CRC_MODE)
^
In file included from /home/build/work/batch/arch/arm64/include/asm/io.h:32:0,
from /home/build/work/batch/include/linux/clocksource.h:19,
from /home/build/work/batch/include/clocksource/arm_arch_timer.h:19,
from /home/build/work/batch/arch/arm64/include/asm/arch_timer.h:27,
from /home/build/work/batch/arch/arm64/include/asm/timex.h:19,
from /home/build/work/batch/include/linux/timex.h:65,
from /home/build/work/batch/include/linux/sched.h:19,
from /home/build/work/batch/arch/arm64/include/asm/compat.h:25,
from /home/build/work/batch/arch/arm64/include/asm/stat.h:23,
from /home/build/work/batch/include/linux/stat.h:5,
from /home/build/work/batch/include/linux/module.h:10,
from /home/build/work/batch/drivers/usb/gadget/function/f_ncm.c:19:
arch/arm64/include/asm/cpufeature.h:27:0: note: this is the location of the previous definition
#define NCAPS 2
So add a ARM64 prefix to avoid such problem.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is not valid to select CONFIG_PM directly without selecting
CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME too, because that breaks
dependencies (ia64 does that) and it is not necessary to select
CONFIG_PM directly if CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is
selected, because CONFIG_PM will be set automatically in that
case (sh does that).
Fix those mistakes.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of using the dev_ops ->stop|start() callbacks for genpd, let's
convert to use genpd's flag field and set it to GENPD_FLAG_PM_CLK.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Earlier implementation assumed last instruction is BPF_EXIT.
Since this is no longer a restriction in eBPF, we remove this
limitation.
Per Alexei Starovoitov [1]:
> classic BPF has a restriction that last insn is always BPF_RET.
> eBPF doesn't have BPF_RET instruction and this restriction.
> It has BPF_EXIT insn which can appear anywhere in the program
> one or more times and it doesn't have to be last insn.
[1] https://lkml.org/lkml/2014/11/27/2
Fixes: e54bcde3d69d ("arm64: eBPF JIT compiler")
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
All functions declared in this file are gone.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: re-order patches so modify board-dt-sam9]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As AT91 !DT code is now removed, cleanup the PIT clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: split patch]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
As putting data which is read mostly together, we can avoid
unnecessary cache line bouncing.
Other architectures, such as ARM and x86, adopted the same idea.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
vsys is the core always-on supply of the Marsboard.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
