IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This changes the TPID of the egress frames to use the TPID stored in the
IFH (internal frame header), which ensures that this is the TPID classified
for the frame at ingress.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rule counter must be cleared when creating a new rule, even if the VCAP
lookup is currently disabled.
This ensures that rules located in VCAPs that use external counters (such
as Sparx5 IS2 and ES0) will have their counter reset even if the VCAP
lookup is not enabled at the moment.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Fixes: 95fa74148d ("net: microchip: sparx5: Reset VCAP counter for new rules")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A valid frame should never use a multicast address as its source MAC
address, so discard these invalid frames.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-14 (ice)
This series contains updates to ice driver only.
Karol extends support for GPIO pins to E823 devices.
Daniel Vacek stops processing of PTP packets when link is down.
Pawel adds support for BIG TCP for IPv6.
Tony changes return type of ice_vsi_realloc_stat_arrays() as it always
returns success.
Zhu Yanjun updates kdoc stating supported TLVs.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Mention CEE DCBX in code comment
ice: Change ice_vsi_realloc_stat_arrays() to void
ice: add support BIG TCP on IPv6
ice/ptp: fix the PTP worker retrying indefinitely if the link went down
ice: Add GPIO pin support for E823 products
====================
Link: https://lore.kernel.org/r/20230214213003.2117125-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the basic ethtool ops get_drvinfo and get_link for ngbe and txgbe.
Ngbe implements get_link_ksettings, nway_reset and set_link_ksettings
for free using phylib code.
The code related to the physical interface is not yet fully implemented
in txgbe using phylink code. So do not implement get_link_ksettings,
nway_reset and set_link_ksettings in txgbe.
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230214091527.69943-1-mengyuanlou@net-swift.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5-updates-2023-02-10
1) From Roi and Mark: MultiPort eswitch support
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort Eswitch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
2) From Jiri: Improvements and fixes for mlx5 netdev's devlink logic
2.1) Cleanups related to mlx5's devlink port logic
2.2) Move devlink port registration to be done before netdev alloc
2.3) Create auxdev devlink instance in the same ns as parent devlink
2.4) Suspend auxiliary devices only in case of PCI device suspend
* tag 'mlx5-updates-2023-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Suspend auxiliary devices only in case of PCI device suspend
net/mlx5: Remove "recovery" arg from mlx5_load_one() function
net/mlx5e: Create auxdev devlink instance in the same ns as parent devlink
net/mlx5e: Move devlink port registration to be done before netdev alloc
net/mlx5e: Move dl_port to struct mlx5e_dev
net/mlx5e: Replace usage of mlx5e_devlink_get_dl_port() by netdev->devlink_port
net/mlx5e: Pass mdev to mlx5e_devlink_port_register()
net/mlx5: Remove outdated comment
net/mlx5e: TC, Remove redundant parse_attr argument
net/mlx5e: Use a simpler comparison for uplink rep
net/mlx5: Lag, Add single RDMA device in multiport mode
net/mlx5: Lag, set different uplink vport metadata in multiport eswitch mode
net/mlx5: E-Switch, rename bond update function to be reused
net/mlx5e: TC, Add peer flow in mpesw mode
net/mlx5: Lag, Control MultiPort E-Switch single FDB mode
====================
Link: https://lore.kernel.org/r/20230214221239.159033-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original behavior introduced by commit c6acd629ee ("net/mlx5e: Add
support for devlink-port in non-representors mode") correctly
re-instantiated uplink devlink port and related netdevice during devlink
reload. However with migration to auxiliary devices, this behaviour
changed.
Restore the original behaviour and tear down auxiliary devices
completely during devlink reload.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_load_one() is always called with recovery==false, so remove the
unneeded function arg.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Commit cited in "fixes" tag moved the devlink port under separate
devlink entity created for auxiliary device. Respect the network
namespace of parent devlink entity and allocate the devlink there.
Fixes: ee75f1fc44 ("net/mlx5e: Create separate devlink instance for ethernet auxiliary device")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move the devlink port registration to be done right after devlink
instance registration.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
No need to have dl_port which is tightly coupled with mlx5e code
in mlx5 core code. Move it to struct mlx5e_dev and loose
mlx5e_devlink_get_dl_port() helper.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On places where netdev pointer is available, access related devlink_port
pointer by netdev->devlink_port instead of using
mlx5e_devlink_get_dl_port() which is going to be removed.
Move SET_NETDEV_DEVLINK_PORT() call right after devlink port
registration to make sure netdev->devlink_port is valid.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The comment is no longer applicable, as the devlink reload and instance
cleanup are both protected with devlink instance lock, therefore no race
can happen.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The parse_attr argument is not being used in
actions_match_supported_fdb(). remove it.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
get_route_and_out_devs() is uses the following condition
mlx5e_eswitch_rep() && mlx5e_is_uplink_rep() to check if a given netdev is the
uplink rep.
Alternatively we can just use the straight forward version
mlx5e_eswitch_uplink_rep() that only checks if a given netdev is uplink rep.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In MultiPort E-Switch mode a single RDMA is created. This device has multiple
RDMA ports that represent the uplink ports that are connected to the E-Switch.
Account for this when creating the RDMA device so it has an additional port for
the non native uplink.
As a side effect of this patch, use shared fdb in multiport eswitch mode.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In a follow-up commit multiport eswitch mode will use a shared fdb.
In shared fdb there is a single eswitch fdb and traffic could come from any
port. to distinguish between the ports set a different metadata per uplink port.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The vport bond update function is really updating the vport metadata
and there is no direct relation to bond. Rename the function
to vport metadata update to be used a followup commit.
This commit doesn't change any functionality.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
While at it rename mlx5_lag_mpesw_is_activated() to mlx5_lag_is_mpesw() to
be consistent with checking if other lag modes are activated.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort E-Switch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
Example:
$ devlink dev param set pci/0000:00:0b.0 name esw_multiport value 1 \
cmode runtime
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
From the function ice_parse_org_tlv, CEE DCBX TLV is also supported.
So update the comment. Or else, it is confusing.
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
smatch reports:
smatch warnings:
drivers/net/ethernet/intel/ice/ice_lib.c:3612 ice_vsi_rebuild() warn: missing error code 'ret'
If an error is encountered for ice_vsi_realloc_stat_arrays(), ret is not
assigned an error value so the goto error path would return success. The
function, however, only returns 0 so an error will never be reported; due
to this, change the function to return void.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Enable sending BIG TCP packets on IPv6 in the ice driver using generic
ipv6_hopopt_jumbo_remove helper for stripping HBH header.
Tested:
netperf -t TCP_RR -H 2001:db8:0:f101::1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,TRANSACTION_RATE
Tested on two different setups. In both cases, the following settings were
applied after loading the changed driver:
ip link set dev enp175s0f1np1 gso_max_size 130000
ip link set dev enp175s0f1np1 gro_max_size 130000
ip link set dev enp175s0f1np1 mtu 9000
First setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
134 279 410 3961.584
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
135 178 216 6093.404
The other setup:
Before:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
218 414 478 2944.765
After:
Minimum 90th 99th Transaction
Latency Percentile Percentile Rate
Microseconds Latency Latency Tran/s
Microseconds Microseconds
146 238 266 4700.596
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the link goes down the ice_ptp_tx_tstamp() may loop re-trying to
process the packets till the 2 seconds timeout finally drops them.
In such a case it makes sense to just drop them right away.
Signed-off-by: Daniel Vacek <neelx@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extend the action stats callback implementation to update stats for actions
that are associated with hw counters.
Note that the callback may be called from tc action utility or from tc
flower. Both apis expect the driver to return the stats difference from
the last update. As such, query the raw counter value and maintain
the diff from the last api call in the tc layer, instead of the fs_core
layer.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently a hardware counter is associated with a flow cookie.
This does not apply to flows using branching action which are required to
return per action stats.
A single counter may apply to multiple actions.
Scan the flow actions in reverse (from the last to the first action) while
caching the last counter.
Associate all the flow attribute tc action cookies with the current
cached counter.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tc parse action phase translates the tc actions to mlx5 flow
attributes data structure that is used during the flow offload phase.
Currently, the flow offload stage instantiates hw counters while
associating them to flow cookie. However, flows with branching
actions are required to associate a hardware counter with its action
cookies.
Store the parsed tc action cookies on the flow attribute.
Use the list of cookies in the next patch to associate a tc action cookie
with its allocated hw counter.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently a hw count action is appended to the last action of the action
list. However, a branching action may terminate the action list before
reaching the last action.
Append a count action to a branching action.
In the next patches, filters with branching actions will read this counter
when reporting stats per action.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ionic device has on-board memory (CMB) that can be used
for descriptors as a way to speed descriptor access for faster
packet processing. It is rumored to improve latency and/or
packets-per-second for some profiles of small packet traffic,
although your mileage may vary.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the pointer already, don't need to go through the
lif struct for it.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the following modes to the nfp driver:
NFP_MEDIA_10GBASE_LR
NFP_MEDIA_25GBASE_LR
NFP_MEDIA_25GBASE_ER
These modes are supported by the hardware and,
support for them was recently added to firmware.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-02-09 (i40e)
Jan removes i40e_status from the driver; replacing them with standard
kernel error codes.
Kees Cook replaces 0-length array with flexible array.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
net/i40e: Replace 0-length array with flexible array
i40e: use ERR_PTR error print in i40e messages
i40e: use int for i40e_status
i40e: Remove string printing for i40e_status
i40e: Remove unused i40e status codes
====================
Link: https://lore.kernel.org/r/20230209172536.3595838-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous code, TX timestamp accuracy was bad because the irq
handler got the timestamp from the timestamp register at that time.
This hardware has "Timestamp capture" feature which can store
each TX timestamp into the timestamp descriptors. To improve
TX timestamp accuracy, implement timestamp descriptors' handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous code, the gptp flag was completely related to
the !dir_tx in struct rswitch_gwca_queue because
rswitch_gwca_queue_alloc() was called below:
< In rswitch_txdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->tx_queue, true, false,
TX_RING_SIZE);
So, dir_tx = true, and gptp = false.
< In rswitch_rxdmac_alloc() >
err = rswitch_gwca_queue_alloc(ndev, priv, rdev->rx_queue, false, true,
RX_RING_SIZE);
So, dir_tx = false, and gptp = true.
In the future, a new queue handling for timestamp will be implemented
and this gptp flag is confusable. So, remove the gptp flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To improve readability, move linkfix related variables to
struct rswitch_gwca. Also, rename function names "desc" with "linkfix".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To add a new ring which is really related to timestamp (ts_ring)
in the future, rename the following members to improve readability:
ring --> tx_ring
ts_ring --> rx_ring
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new user of MSCC_OCELOT_SWITCH_LIB was added, bringing back an old
link failure that was fixed with e5f3155267 ("ethernet: fix
PTP_1588_CLOCK dependencies"):
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_ptp_enable':
ocelot_ptp.c:(.text+0x8ee): undefined reference to `ptp_find_pin'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_get_ts_info':
ocelot_ptp.c:(.text+0xd5d): undefined reference to `ptp_clock_index'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_init_timestamp':
ocelot_ptp.c:(.text+0x15ca): undefined reference to `ptp_clock_register'
x86_64-linux-ld: drivers/net/ethernet/mscc/ocelot_ptp.o: in function `ocelot_deinit_timestamp':
ocelot_ptp.c:(.text+0x16b7): undefined reference to `ptp_clock_unregister'
Add the same PTP dependency here, as well as in the MSCC_OCELOT_SWITCH_LIB
symbol itself to make it more obvious what is going on when the next
driver selects it.
Fixes: 3d7316ac81 ("net: dsa: ocelot: add external ocelot switch control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230209124435.1317781-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
