IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Suspend and crash dump operations can happen simultaneously
in case there is a FW assert during the suspend procedure
or when SSR calls all the devices crashdump callbacks.
To prevent that, a new flag is added, indicating that the
dumps collection is in progress, in order to allow the
suspend/reset decline if the dumps collection already started.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases the platform should be aware of the FW capabilities
to decide which feature to enable.
For example, FW can control the external REF clock for power saving.
Driver should notify the platform about that, to allow platform
power management optimization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add get_capa callback to platform ops to allow reading the platform
capabilities.
Supported capabilities:
- Keeping 11ad connection during suspend
- T_POWER_ON 0 support
- Usage of external clock
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-arrange the code to have dedicated function for device configuration
which takes place before FW starts running.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While wil_open is executed, any call to netif_running
would return a success. In case there are failures
within wil_open, should not treat the device as if it
is already opened in relevant functions (like FW recovery
and runtime suspend check).
Fix that by checking the device up flag instead.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Communication with FW must be done before wil->status
is initialized in order to properly handle cases where
communication with FW halts during reset sequence.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new value to the oob_mode module parameter for
supporting AP certification.
All enabled values of oob_mode (>0) are intended only
for debugging and diagnostics.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon connect timeout driver invokes _wil6210_disconnect() which iterates
over sta array and disconnects each connected sta. In practice, because
the connection is still ongoing and because cid is not yet allocated,
disconnect is not actually happening. This leaves FW in connecting
state while driver is in disconnected state.
To fix this, upon connect timeout, explicitly send WMI_DISCONNECT_CMDID
to FW to make sure it gets disconnected.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After setting HALP ICR bit, we keep it set until HALP unvote.
Masking HALP ICR should protect the driver from hitting the HALP ICR
over and over again. However, in case there is another MISC ICR
we will read the HALP ICR and issue a completion. This can lead to
a case where HALP voting is completed immediately, as the completion
is already set.
Reinit the HALP completion before the actual vote will clear previous
completions and protect from such cases.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver uses the bus_request platform operation to
request resources from the platform for a specific bandwidth.
Currently the driver requests resources for the maximum
theoretical bandwidth, when interface is brought up.
Refine this process a bit: now the driver will request a
small amount of resources when interface is up, and will only
issue the maximum request when connected.
This mechanism will be improved further in the future to make
more refined requests based on actual bandwidth.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Symbolic permissions are no longer recommended.
This patch changes the symbolic permissions in wil6210 driver
to octal permissions.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During reset sequence it is seen that device is generating an
interrupt eventhough interrupts are masked at device level.
Add workaround to disable the interrupts from host side during
reset and clear any pending interrupts before re-enabling
the interrupt.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
__func__ is automatically added to printouts by dynamic debug
mechanism and by wil_info/wil_err macros.
Remove __func__ from debug printouts to avoid duplication.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver may be used in platforms where some use sparrow cards while
other use sparrow-plus cards, where different FW image is needed.
Add the capability to load dedicated FW image in case sparrow-plus
card is detected and fallback to default image if such does not exist.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, AP SME is handled by driver/FW.
In case disable_ap_sme is true, driver doesn't turn-on
WIPHY_FLAG_HAVE_AP_SME and the responsibility for
AP SME is passed to user space.
With AP SME disabled, driver reports assoc request frame
to user space which is then responsible for sending assoc
response frame and for sending NL80211_CMD_NEW_STATION.
Driver also reports disassoc frame to user space
which should then send NL80211_CMD_DEL_STATION.
NL80211_CMD_SET_STATION with NL80211_STA_FLAG_AUTHORIZED
is used by user space to allow/disallow data transmit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.
The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the FW version is taken from the sw_version field
of the FW ready event. This version is based on internal
version control revision and it is difficult to map to actual
FW version.
Fix this by using the actual FW version stored in the FW file
header record.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When driver is loaded, extract a capabilities record
from the FW file. This record contains bits indicating
which optional features are supported by this FW.
The driver can use this information to determine
which functionality to support and/or expose to user
space.
The extraction is done before wiphy structure is
registered, because the capabilities can affect
information published by the this structure.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the places that check wil->scan_request and
call cfg80211_scan_done are not consistently protected,
so there is a risk that cfg80211_scan_done will be called
with NULL scan_request, causing a kernel crash.
Fix this by using p2p_wdev_mutex in few other places
that access scan_request. This makes sense since
scan_request may point to p2p_wdev, and it is not worth
the extra complexity of adding a new mutex.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently wiphy structure is initialized and registered
in wil_if_alloc, before some information is available such
as MAC address and capabilities. As a result there is a
small chance user space will get incorrect information
from calls such as NL80211_CMD_GET_WIPHY.
Fix this by seperating the registration and moving it
to wil_if_add which is executed later, after all
relevant information is known.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stations disconnection is executed as part of wil_reset so no
need to do it in wil_down.
Removal of the disconnect operation will also preserve the lock
of wil->mutex during the whole reset flow and prevent handling of
connect event while resetting.
Set wil_status_resetting in earlier stage in the flow to prevent
double resetting call in case communication with FW fails while
bringing the interface down.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix stop p2p device handling to identify between search
and listen and update the upper layers with the appropriate
notification.
The stop of p2p radio operations also needs to be performed
in __wil_down.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the logging category of HALP functions from
MISC to IRQ, since the HALP mechanism is closely
related to interrupts. Both HALP and IRQ create
a heavy load of logging messages when enabled,
so their logging is typically disabled during normal debug
scenarios. Having them in the same logging category
will make it easier to disable logging for both in one go.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case HALP vote times out, we need to mask the HALP IRQ, as done
in case the interrupt is received, as this interrupt should be
set until completion of the low latency operation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure the device led to be used for notifying
the AP activity (60G device supports leds 0-2).
The host can also configure the blinking frequency of the led in
three states.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In idle times 60G device can enter deep sleep and turn off
its XTAL clock.
Host access triggers the device power-up flow which will hold
the AHB during XTAL stabilization until device switches from
slow-clock to XTAL clock.
This behavior can stall the PCIe bus for some arbitrary period
of time.
In order to prevent this stall, host can vote for High Latency
Access Policy (HALP) before reading from PCIe bus.
This vote will wakeup the device from deep sleep and prevent
deep sleep until unvote is done.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
RX_HTRSH interrupt sometimes triggered during device reset
procedure.
To prevent handling this interrupt when not required, unmask
this interrupt only if we are connected and mask it when
disconnected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add module parameter oob_mode. Takes effect the next time
the interface is brought up and FW is loaded. Puts the FW
in special "out of the box" (OOB) mode which is used for
diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashed with no_fw_recovery mode enabled, user space
could still call wil_cfg80211_change_iface quickly to change
interface type, and this would cause recovery to proceed and
FW crash logs may be lost.
Fix this problem by not resetting the FW in case no_fw_recovery
is enabled.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
