IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
controllers with XHCI_AVOID_BEI quirk cause too frequent interrupts
and affect power management.
To avoid interrupting on every isochronous interval the BEI (Block
Event Interrupt) flag is set for all except the last Isoch TRB in a URB.
This lead to event ring filling up in case several isoc URB were
queued and cancelled rapidly, which some controllers didn't
handle well, and thus the XHCI_AVOID_BEI quirk was introduced.
see commit 227a4fd801 ("usb: xhci: apply XHCI_AVOID_BEI quirk to all
Intel xHCI controllers")
With the XHCI_AVOID_BEI quirk each Isoch TRB will trigger an interrupt.
This can cause up to 8000 interrupts per second for isochronous transfers
with HD USB3 cameras, affecting power saving.
The event ring fits 256 events, instead of interrupting on every
isochronous TRB if XHCI_AVOID_BEI is set we make sure at least every
8th Isochronous TRB asserts an interrupt, clearing the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comment in usb_alloc_dev correctly states, drivers can't use
the DMA API on usb device, and at least calling dma_set_mask on them
is highly dangerous. Unlike what the comment states upper level drivers
also can't really use the presence of a dma mask to check for DMA
support, as the dma_mask is set by default for most busses.
Setting the dma_mask comes from "[PATCH] usbcore dma updates (and doc)"
in BitKeeper times, as it seems like it was primarily for setting the
NETIF_F_HIGHDMA flag in USB drivers, something that has long been
fixed up since.
Setting the dma_pfn_offset comes from commit b44bbc46a8
("usb: core: setup dma_pfn_offset for USB devices and, interfaces"),
which worked around the fact that the scsi_calculate_bounce_limits
functions wasn't going through the proper driver interface to query
DMA information, but that function was removed in commit 21e07dba9f
("scsi: reduce use of block bounce buffers") years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ROLE_CONTROL register would not have the actual CC terminations
unless the port does not set ROLE_CONTROL.DRP. For DRP ports,
CC_STATUS.cc1/cc2 indicates the final terminations applied
when TCPC enters potential_connect_as_source/_sink.
For DRP ports, infer port role from CC_STATUS and set corresponding
CC terminations before setting the orientation.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649b ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI specification quite clearly states that if a command
can't be completed in 10ms, the firmware must notify
about BUSY condition. Unfortunately almost none of the
platforms (the firmware on them) generate the BUSY
notification even if a command can't be completed in time.
The driver already considered that, and used a timeout
value of 5 seconds, but processing especially the alternate
mode discovery commands takes often considerable amount of
time from the firmware, much more than the 5 seconds. That
happens especially after bootup when devices are already
connected to the USB Type-C connector. For now on those
platforms the alternate mode discovery has simply failed
because of the timeout.
To improve the situation, increasing the timeout value for
the command completion to 1 minute. That should give enough
time for even the slowest firmware to process the commands.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New core functions to make sending/receiving USB control messages easier
and saner.
In discussions, it turns out that the large majority of users of
usb_control_msg() do so in potentially incorrect ways. The most common
issue is where a "short" message is received, yet never detected
properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make
working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only
"complete" send/receive will work without causing an error.
Link: https://lore.kernel.org/r/20200914153756.3412156-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Johan writes:
USB-serial fixes for 5.9-rc5
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: support dynamic Quectel USB compositions
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
The PMC microcontroller that we use for configuration, does
not supply any status information back. For port status we
need to talk to another controller on the board called IOM
(I/O manager).
By checking the port status before configuring the muxes, we
can make sure that we do not reconfigure the port after
bootup when the system firmware (for example BIOS) has
already configured it.
Using the status information also to check if DisplayPort
HPD is still asserted when the cable plug is disconnected,
and clearing it if it is.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.
Fixes: ff4a30d5e2 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.
Fixes: 7990be48ef ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
