IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var) which helps readability
and also handles all corner-cases properly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
if atmel,pmecc-lookup-table-offset is not found in DT node, we don't
need to map the ROM table as we will build a runtime gf table anyway.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's better to use a macro instead of just a number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch makes MTD dynamic partitioning more flexible by removing
overlap checks for dynamic partitions. I don't see any particular
reason why overlapping dynamic partitions should be prohibited while
static partitions are allowed to overlap freely.
The checks previously had an off-by-one error, where 'end' should be
one less than what it is currently set at, and adding partitions out of
increasing order will fail. Disabling the checks resolves this issue.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch makes a sysfs variable called 'offset' on each partition
which contains the offset in bytes from the beginning of the master
device that the partition starts.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For many use cases, it helps to have a device node for the entire
MTD device as well as device nodes for the individual partitions.
For example, this allows querying the entire device's properties.
A common idiom is to create an additional partition which spans
over the whole device.
This patch makes a config option, CONFIG_MTD_PARTITIONED_MASTER,
which makes the master partition present even when the device is
partitioned. This isn't turned on by default since it presents
a backwards-incompatible device numbering.
The patch also makes the parent of a partition device be the master,
if the config flag is set, now that the master is a full device.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes a spelling typo in MODULE_DESCRIPTION in
ts5500_flash.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
[ Brian: fixed grammar in a spelling patch :) ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Denali Controller IP does not support sub-page writes.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
The variable used for handling the return of wait_for_cmpletion_timeout
was int but should be unsigned long, where it was not in use for
anything else and the return value in case of completion (>0) is not
used it was removed and wait_for_completion_timeout() used directly in
the if condition.
To make the timeout values a bit simpler to read and also handle all of
the corner cases correctly the declarations are moved to
msecs_to_jiffies().
The timeout declaration cleanup is just for readability
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case of scan_bbt() failure, we should better propagate it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When displaying dev_err() messages it is useful to print the error value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
[Brian: fix up "can not" at the same time]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These lines were all indented one tab more than they should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Without this patch the timings are all set to 0 if not specified in the dts.
With this patch the driver falls back to use the defaults that are already
present in the driver and are known to work okay for some (older) boards.
Tested on a custom SPEAr600 based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a NAND device is not really present or pin muxes are not correctly
configured we can lock up the kernel waiting infinitely for NAND_STATUS
to be ready.
This can be easily reproduced on TI's DRA7-evm board by booting it
without NAND support in u-boot and disabling NAND pin muxes in the kernel.
Add timeout when waiting for NAND_CMD_RESET completion. As per ONFi v4.0
tRST can be upto 250ms for EZ-NAND and 5ms for raw NAND.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Flash lock/unlock is a flash-specific operations. Factor out a callback
for it to more readily support other vendors.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: VIET NGA DAO <vndao@altera.com>
If we encounter an uncorrectable ECC error while scanning for the fastmap
UBI must not fail hard. Instead fall back to scanning mode.
Reported-by: Alexander Block <Alexander.Block@continental-corporation.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This function was added to fastmap in a very early stage
to have paranoid assertions.
With the current fastmap implementation this assert will never
trigger as fastmap PEBs are not seen by the WL sub-system.
Remove it to save us some CPU cycles.
Signed-off-by: Richard Weinberger <richard@nod.at>
Fastmap need access to various WL data structures as
fastmap tightly depends on WL.
To make the access less invasive add accessor functions.
Signed-off-by: Richard Weinberger <richard@nod.at>
Fastmap is tightly connected to the WL sub-system, many fastmap-specific
functionslive in wl.c.
To get rid of most #ifdefs in wl.c move this functions into a new file
and include it into wl.c
Signed-off-by: Richard Weinberger <richard@nod.at>
If fm_debug is set fastmap debugging is enabled by default.
This is useful if one wants to debug fastmap on an UBI device
with serves the rootfs.
The the UBI attach mechanism runs long before debugfs can be mounted
and chk_fastmap set.
Signed-off-by: Richard Weinberger <richard@nod.at>
This self check allows Fastmap to detect absent PEBs while
writing a new fastmap to the MTD device.
It will help to find implementation issues in Fastmap.
Signed-off-by: Richard Weinberger <richard@nod.at>
In some error paths the WL sub-system gives up on a PEB
and frees it's ubi_wl_entry struct but does not set
the entry in ubi->lookuptbl to NULL.
Fastmap can stumble over such a stale pointer as it uses
ubi->lookuptbl to find all PEBs.
Fix this by introducing a new helper function which free()s
a WL entry and removes the reference from the lookup table.
Signed-off-by: Richard Weinberger <richard@nod.at>
Don't update the fastmap upon detach if fastmap checking is enabled.
This is poor men's power cut testing feature. :-)
Signed-off-by: Richard Weinberger <richard@nod.at>
Using this debugfs knob fastmap self checks can be controlled.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
If UBI is unable to write the fastmap to the device
we have make sure that upon next attach UBI will fall
back to scanning mode.
In case we cannot ensure that they only thing we can do
is falling back to read-only mode.
The current error handling code is not powercut proof.
It could happen that a powercut while invalidating would
lead to a state where an too old fastmap could be used upon
attach.
This patch addresses the issue by writing a fake fastmap
super block to a fresh PEB instead of reerasing the existing one.
The fake fastmap super block will UBI case to do a full scan.
Signed-off-by: Richard Weinberger <richard@nod.at>
The current code assumes that each fastmap has the same amount of PEBs.
So far this is true but will change soon.
Signed-off-by: Richard Weinberger <richard@nod.at>
a) Rename ubi->fm_sem to ubi->fm_eba_sem as this semaphore
protects EBA changes.
b) Turn ubi->fm_mutex into a rw semaphore. It will still serialize
fastmap writes but also ensures that ubi_wl_put_peb() is not
interrupted by a fastmap write. We use a rw semaphore to allow
ubi_wl_put_peb() still to be executed in parallel if no fastmap
write is happening.
Signed-off-by: Richard Weinberger <richard@nod.at>
ubi_wl_get_peb() returns a fresh PEB which can be used by
user of UBI. Due to the pool logic fastmap will correctly
map this PEB upon attach time because it will be scanned.
If a new fastmap is written (due to heavy parallel io)
while the before the fresh PEB is assigned to the EBA table
it will not be scanned as it is no longer in the pool.
So, the race window exists between ubi_wl_get_peb()
and the EBA table assignment.
We have to make sure that no new fastmap can be written
while that.
To ensure that ubi_wl_get_peb() will grab ubi->fm_sem in read mode
and the user of ubi_wl_get_peb() has to release it after the PEB
got assigned.
Signed-off-by: Richard Weinberger <richard@nod.at>
Don't use a fixed size for the WL pool.
Make it instead 50% of the user pool.
We don't make it 100% as it is not as heavily used as the user pool.
Signed-off-by: Richard Weinberger <richard@nod.at>
This logic is in vain as we treat protected PEBs also as used, so this
case must not happen.
If a PEB is found which is in the EBA table but not known as used
has to be issued as fatal error.
Signed-off-by: Richard Weinberger <richard@nod.at>
It is legal to have PEBs left in the used list.
This can happen if UBI copies a PEB and a powercut happens
between writing a new fastmap and adding this PEB into the EBA table.
In this case the old PEB will be used.
Signed-off-by: Richard Weinberger <richard@nod.at>
This function a) requests a new PEB, b) writes data to it,
c) returns the old PEB and d) registers the new PEB in the EBA table.
For the non-fastmap case this works perfectly fine and is powercut safe.
Is fastmap enabled this can lead to issues.
If a new fastmap is written between a) and c) the freshly requested PEB
is no longer in a pool and will not be scanned upon attaching.
If now a powercut happens between c) and d) the freshly requested PEB
will not be scanned and the old one got already scheduled for erase.
After attaching the EBA table will point to a erased PEB.
Fix this issue by swapping steps c) and d).
Signed-off-by: Richard Weinberger <richard@nod.at>
There is always exactly one ubi_attach_info object allocated,
therefore we don't have to care about the name.
Signed-off-by: Richard Weinberger <richard@nod.at>
There is no need to switch to ro mode if ubi_update_fastmap() fails.
Also get rid of the ifdef.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
...such that we can implement NOP variants of some functions.
This will help to reduce fastmap specific ifdefs in other c files.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
If ubi_update_fastmap() fails notify the user.
This is not a hard error as ubi_update_fastmap() makes sure that upon failure
the current on-flash fastmap will no be used upon next UBI attach.
Signed-off-by: Richard Weinberger <richard@nod.at>
