IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Re-write the end of 'nl80211_trigger_scan()' with a more standard, easy to
understand and future proof version.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173551.274448-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 5fe231e873 ("cfg80211: vastly simplify locking"), the
'unlock' label at the end of 'nl80211_trigger_scan()' is useless and
misleading, because nothing is unlocked there.
Direct return can be used instead of 'err = -<error code>; goto unlock;'
construction.
Remove this label and simplify code accordingly.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173539.274395-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211 vendor netlink dumpit, like netlink_callback->dump, should
signal successful completion by returning 0.
Currently, that will just cause dumpit to be called again, possibly
many times until an error occurs. Since skb->len is never going to be
0 by the time dumpit is called, the only way for dumpit to signal
completion is by returning an error. If it returns a positive value,
the current message is cancelled, but that positive value is returned
and nl80211_vendor_cmd_dump gets called again.
Fix that by passing a return value of 0 through.
Signed-off-by: Julian Squires <julian@cipht.net>
Link: https://lore.kernel.org/r/20200720145033.401307-1-julian@cipht.net
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently rates_idx is being initialized with the value -1 and this
value is never read so the initialization is redundant and can be
removed. The next time the variable is used it is assigned a value
that is returned a few statements later. Just return i - 1 and
remove the need for rates_idx.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200722153830.959010-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters. This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.
The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.
Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#378 [hci0] 1659.247156
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#39 [hci0] 7.422109
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 60.000 msec (0x0060)
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaibhav Gupta says:
====================
net: ethernet: use generic power management
Linux Kernel Mentee: Remove Legacy Power Management.
The purpose of this patch series is to upgrade power management in net ethernet
drivers. This has been done by upgrading .suspend() and .resume() callbacks.
The upgrade makes sure that the involvement of PCI Core does not change the
order of operations executed in a driver. Thus, does not change its behavior.
In general, drivers with legacy PM, .suspend() and .resume() make use of PCI
helper functions like pci_enable/disable_device_mem(), pci_set_power_state(),
pci_save/restore_state(), pci_enable/disable_device(), etc. to complete
their job.
The conversion requires the removal of those function calls, change the
callbacks' definition accordingly and make use of dev_pm_ops structure.
All patches are compile-tested only.
Test tools:
- Compiler: gcc (GCC) 10.1.0
- allmodconfig build: make -j$(nproc) W=1 all
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory, so memset is not needed
dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of struct octeon_dispatch is too small, it is better to use
kmalloc instead of vmalloc.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure.
This helper offers defense-in-depth against potential integer
overflows, while at the same time makes it explicitly clear that
we are dealing with a flexible array member.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure.
This helper offers defense-in-depth against potential integer
overflows, while at the same time makes it explicitly clear that
we are dealing witha flexible array member.
Also, remove unnecessary pointer identifier sub_pool.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 4.8.7 firmware, adjtime can change delta instead of absolute time,
which greately increases snap accuracy. PPS alignment doesn't have to
be set for every single TOD change. Other minor changes includes:
adding more debug logs, increasing snap accuracy for pre 4.8.7 firmware
and supporting new tcs2bin format.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Parkin says:
====================
l2tp: tidy up l2tp core API
This short series makes some minor tidyup changes to the L2TP core API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Improve the description of the key l2tp subsystem data structures.
* Add high-level description of the main APIs for interacting with l2tp
core.
* Add documentation for the l2tp netlink session command callbacks.
* Document the session pseudowire callbacks.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the l2tp subsystem's exported symbols are exported using
EXPORT_SYMBOL_GPL, except for l2tp_recv_common and l2tp_ioctl.
These functions alone are not useful without the rest of the l2tp
infrastructure, so there's no practical benefit to these symbols using a
different export policy.
Change these exports to use EXPORT_SYMBOL_GPL for consistency with the
rest of l2tp.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure of an L2TP data packet header varies depending on the
version of the L2TP protocol being used.
struct l2tp_session used to have a build_header callback to abstract
this difference away. It's clearer to simply choose the correct
function to use when building the data packet (and we save on the
function pointer in the session structure).
This approach does mean dereferencing the parent tunnel structure in
order to determine the tunnel version, but we're doing that in the
transmit path in any case.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_delete is used to schedule a session instance for deletion.
The function itself always returns zero, and none of its direct callers
check its return value, so have the function return void.
This change de-facto changes the l2tp netlink session_delete callback
prototype since all pseudowires currently use l2tp_session_delete for
their implementation of that operation.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel and session instances are reference counted, and shouldn't be
directly freed by pseudowire code.
Rather than exporting l2tp_tunnel_free and l2tp_session_free, make them
private to l2tp_core.c, and export the refcount functions instead.
In order to do this, the refcount functions cannot be declared as
inline. Since the codepaths which take and drop tunnel and session
references are not directly in the datapath this shouldn't cause
performance issues.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __l2tp_session_unhash was first added it was used outside of
l2tp_core.c, but that's no longer the case.
As such, there's no longer a need to export the function. Make it
private inside l2tp_core.c, and relocate it to avoid having to declare
the function prototype in l2tp_core.h.
Since the function is no longer used outside l2tp_core.c, remove the
"__" prefix since we don't need to indicate anything special about its
expected use to callers.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txtimestamp selftest sets a fixed 500us tolerance. This value was
arrived at experimentally. Some platforms have higher variances. Make
this adjustable by adding the following flag:
-t N: tolerance (usec) for timestamp validation.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-07-30
Please note that I did the first time now --no-ff merges
of my testing branch into the master branch to include
the [PATCH 0/n] message of a patchset. Please let me
know if this is desirable, or if I should do it any
different.
1) Introduce a oseq-may-wrap flag to disable anti-replay
protection for manually distributed ICVs as suggested
in RFC 4303. From Petr Vaněk.
2) Patchset to fully support IPCOMP for vti4, vti6 and
xfrm interfaces. From Xin Long.
3) Switch from a linear list to a hash list for xfrm interface
lookups. From Eyal Birger.
4) Fixes to not register one xfrm(6)_tunnel object twice.
From Xin Long.
5) Fix two compile errors that were introduced with the
IPCOMP support for vti and xfrm interfaces.
Also from Xin Long.
6) Make the policy hold queue work with VTI. This was
forgotten when VTI was implemented.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignment.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignments.
Issue found with checkpatch.pl
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace memsets of 1 byte with simple assignments.
Issue reported by checkpatch.pl.
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let
PCI core handle the work.
e100_suspend() calls __e100_shutdown() to perform intermediate tasks.
__e100_shutdown() calls pci_save_state() which is not recommended.
e100_suspend() also calls __e100_power_off() which is calling PCI helper
functions, pci_prepare_to_sleep(), pci_set_power_state(), along with
pci_wake_from_d3(...,false). Hence, the functin call is removed and wol is
disabled as earlier using device_wakeup_disable().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
and pci_enable/disable_device(), which is not recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let
PCI core handle the work.
ixgbe_suspend() calls __ixgbe_shutdown() to perform intermediate tasks.
__ixgbe_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.
Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove legacy PM callbacks and use generic operations. With legacy code,
drivers were responsible for handling PCI PM operations like
pci_save_state(). In generic code, all these are handled by PCI core.
The generic suspend() and resume() are called at the same point the legacy
ones were called. Thus, it does not affect the normal functioning of the
driver.
__maybe_unused attribute is used with .resume() but not with .suspend(), as
.suspend() is called by .shutdown().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves. The required operations are
done by PCI core.
PCI drivers are not expected to invoke PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_set_power_state(), etc. Their tasks are completed by PCI core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit 7ecacafc24.
Testing this change on a board with RTL8822CE, I found that enabling
autosuspend has no effect on the stability of the system. The board
continued working after autosuspend, suspend and reboot.
The original commit makes it impossible to enable autosuspend on working
systems so it should be reverted. Disabling autosuspend should be done
via module param or udev in userspace instead.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
