IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Since it uses the same NIC table as rx flow vlan filter therefore
rx-flow vlan filter accepts only vlans that present on the interface
in case of rx-vlan-filter is on.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 EtherType filters allows to filter packet by EtherType field or
both EtherType and User Priority (PCP) field of 802.1Q.
UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That
is to distinguish VLAN filter from L2 Ethertype filter with
UserPriority since both User Priority and VLAN ID are passed in the
same 'vlan' parameter.
Example:
To add a filter that directs IP4 packess of priority 3 to queue 3:
ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF \
action 3 loc 16
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN filter (VLAN id) is compared against 16 filters.
VLAN id must be accompanied by mask 0xF000. That is to distinguish
VLAN filter from L2 Ethertype filter with UserPriority since both
User Priority and VLAN ID are passed in the same 'vlan' parameter.
Flow type may be any as it is not matched for VLAN filter.
Due to fixed order of the rules in the NIC, the location 0-15 are
reserved for vlan filters.
Example:
To add a rule that directs packets from VLAN 2001 to queue 5:
ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 5 loc 0
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of L3/L4 5-tuple {protocol, src-ip, dst-ip, src-port, dst-port}
filters. Mask is not supported. Src-port and dst-port are only compared for
TCP/UDP/SCTP packets. Both IPv4 and IPv6 are supported.
The supported actions are the drop and the queue assignment.
Due to fixed order of the rules in the NIC, the location 32-39 are
reserved for L3/L4 5-tuple filters. The locations 32 and 36 are
reserved for IPv6 filters.
Examples:
sudo ethtool -N eth0 flow-type ip6 src-ip 2001:db8:0:f101::2 \
dst-ip 2001:db8:0:f101::5 action -1 loc 36
sudo ethtool -N eth0 flow-type udp4 src-ip 10.0.0.4 \
dst-ip 10.0.0.7 src-port 2000 dst-port 2001 action 2 loc 32
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to support ntuple filter configuration.
Add rule, remove rule, reapply on interface up.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing register definitions and the functions accessing them
related to rx-flow filters.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Checksum offloads could not be configured and ignored netdev features
flag for checksumming.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.
The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.
Fixes: 94b3b54230 ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.
Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.
This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45 ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c:282:5: warning:
symbol 'aq_fw2x_update_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several variables being initialized that are being set later
and hence the initialization is redundant and can be removed. Remove
then.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning:
symbol 'aq_fw1x_set_power' was not declared. Should it be static?
Fixes: a0da96c08c ("net: aquantia: implement WOL support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra characters from the names of structures to unify prefixes
used through the driver code (we normally use hw_atl for hw specifics).
HW_ATL_B0_ and HW_ATL_A0_ are the same and useless copies.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra spaces, corrected alignment.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add WOL support. Currently only magic packet
(ethtool -s <ethX> wol g) feature is implemented.
Remove hw_set_power and move that to FW_OPS set_power:
because WOL configuration behaves differently on 1x and 2x
firmwares
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added definitions and structures needed to support WOL.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the upload function, which worked incorrectly with
some chips.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.
Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc and/or allmulti to pass
the traffic in.
We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.
Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:525:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:536:5: warning:
symbol 'hw_atl_utils_mpi_set_state' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime change of pause frame configuration (rx/tx flow control)
via ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now pass link drop status to FW on init/deinit. This is required
to inform FW that driver took/released a control on link.
FW then will manage its own state and device power profile based
on this information. To improve management we remove mpi_set
function which ambiguously took both state and speed parameters.
Deinit callback is now a part of FW ops, as it actually manages the FW.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented ring size setup, min/max validation and reconfiguration in
runtime.
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Colin Ian King <colin.king@canonical.com>
This was originally mistakenly submitted to net-next. Resubmitting to net.
The comparison of numvecs < 0 is always false because numvecs is a u32
and hence the error return from a failed call to pci_alloc_irq_vectores
is never detected. Fix this by using the signed int ret to handle the
error return and assign numvecs to err.
Detected by CoverityScan, CID#1468650 ("Unsigned compared against 0")
Fixes: a09bd81b54 ("net: aquantia: Limit number of vectors to actually allocated irqs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function aq_fw2x_get_mac_permanent is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'aq_fw2x_get_mac_permanent' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should use pci_alloc_irq_vectors return value to correct number
of allocated vectors and napi instances. Otherwise it'll panic later
in pci_irq_vector.
Driver also should allow more than one MSI vectors to be allocated.
Error return path from pci_alloc_irq_vectors is also fixed to revert
resources in a correct sequence when error happens.
Reported-by: Long, Nicholas <nicholas.a.long@baesystems.com>
Fixes: 23ee07a ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, not reporting SG forced skbs to be linear for vlan
interfaces over atlantic NIC.
With this fix it is possible to enable SG feature on device and
therefore optimize performance.
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case netdev is closed at the moment of pci shutdown, aq_nic_stop
gets called second time. napi_disable in that case hangs indefinitely.
In other case, if device was never opened at all, we get oops because
of null pointer access.
We should invoke aq_nic_stop conditionally, only if device is running
at the moment of shutdown.
Reported-by: David Arcari <darcari@redhat.com>
Fixes: 90869ddfef ("net: aquantia: Implement pci shutdown callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ASUS XG-C100C with 1.5.44 firmware a special mode called "dirty wake"
is active. With this mode when motherboard gets powered (but no poweron
happens yet), NIC automatically enables powersave link and watches
for WOL packet.
This normally allows to powerup the PC after AC power failures.
Not all motherboards or bios settings gives power to PCI slots,
so this mode is not enabled on all the hardware.
4.16 linux driver introduced full hardware reset sequence
This is required since before that we had no NIC hardware
reset implemented and there were side effects of "not clean start".
But this full reset is incompatible with "dirty wake" WOL feature
it keeps the PHY link in a special mode forever. As a consequence,
driver sees no link and no traffic.
To fix this we forcibly change FW state to idle state before doing
the full reset. This makes FW to restore link state.
Fixes: c8c82eb net: aquantia: Introduce global AQC hardware reset sequence
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:508:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should close link and all NIC operations during shutdown.
On some systems graceful reboot never closes NIC interface on its own,
but only indicates pci device shutdown. Without explicit handler, NIC
rx rings continued to transfer DMA data into prepared buffers while CPU
rebooted already. That caused memory corruptions on soft reboot.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing prevents us from changing MAC on the running interface.
Allow this with ndev priv flag.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should report to napi full budget only when we have more job to do.
Before this fix, on any tx queue cleanup we forced napi to do poll again.
Thats a waste of cpu resources and caused storming with napi polls when
there was at least one tx on each interrupt.
With this fix we report full budget only when there is more job on TX
to do. Or, as before, when rx budget was fully consumed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B1 hardware changes behavior of mailbox interface, it has busy bit
always raised. Data ready condition should be detected by increment
of address register.
Old code has empty `for` loop, and that caused cpu overloads on B1
hardware. aq_nic_service_timer_cb consumed ~100ms because of that.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW 1.5.58 and below needs a fixed delay even after 0x18 register
is filled. Otherwise, setting MPI_INIT state too fast causes
traffic hang.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances (notably using thunderbolt interface) SPI
on chip reset may be in active transaction.
Here we forcibly cleanup SPI to prevent possible hangups.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:50:34: warning:
symbol 'hw_atl_boards' was not declared. Should it be static?
Fixes: 4948293ff9 ("net: aquantia: Introduce new AQC devices and capabilities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the aq_ndev_alloc() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices with known capabilities of Fibre media type we now report that
to ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These ops are not related to HW and are now implemented in pci module.
Thus, remove these ops pointers and implementation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver contained a dead code of maintaining multiple pci port instances.
That will never be used since for each pci function a separate NIC
instance is created.
Simplify this, making pci module only responsible for pci resource
management.
NIC initialization is also simplified accordingly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes unnecessary structure copying, and prepares the driver for
separate firmware ops table introduction.
We also remove extra copy of capabilities structure (which is const actually)
and also replace it with a const pointer in aq_nic_cfg.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of new AQC devices is going to be released. To support more
flexible capabilities management a number of static caps instances is now
declared. Devices now are mainly differs by supported speeds, but in future
more parameters will be customized. A set of AQC100 devices have
fibre media, not twisted pair - this is also reflected in
new capabilities definitions.
HW level also now directly exports hw_ops for each of A0/B0 hardware.
PCI configuration now uses a device configuration table where each
device ID is explicitly mapped with hardware OPs and capabilities
structures.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New set of aquantia devices has an upgraded hardware (B1).
The hardware interface is identical to B0. The difference will
be in firmware which is incompatible with old one.
Reorganized and removed duplicate speed and devid definitions
Introduced explicit flow control configuration defines
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb len should be fetched before gro_receive - otherwise we may get
wrong or even outdated skb data.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal functions for registers and HW access were not prefixed.
This introduce noise in global kernel symbols. Here we add explicit prefix
'hw_atl' to all the HW access layer functions.
Alignment and styling were fixed as well.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original driver code had internal registers and masks declarations
in low case and without any prefix.
Here we make all these uppercase and add already used HW_ATL prefix
to recognize these.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_s was hidden in aq_nic_internal.h, that made it difficult to access
nic fields and structures from other modules.
This change moves aq_nic_s struct into aq_nic.h and thus makes it available
to other driver modules, mainly pci module and hw related module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate useless passing of net_device_ops and ethtools_ops through
deep chain of calls.
Move all pci related code into aq_pci_func module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware operations and capabilities tables are constants and
never changed. Declare these as constants.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use direct aq_hw_s *self reference where possible
Eliminate useless abstraction PHAL, duplicated structures definitions,
Simplify nic config structure creation and management.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of aq_obj_s structure is noop, here we remove it
replacing access to flags filed directly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a suffix to distinguish kernel mainline version and aquantia releases
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On very first start we should read out current HW counter values
to make diff based calculations later.
This also should be done each time NIC gets down/up or wakes up
after sleep state. We reset link state explicitly to prevent diffs
from being summed this first time.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce timeout from 2 secs to 1 sec. If link is down,
reduce it to 500msec. This speeds up link detection.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This metric comes from HW and is also diff-calculated, like other counters
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally they were filled from ring sw counters.
These sometimes incorrectly calculate byte and packet amounts
when using LRO/LSO and jumboframes. Filling ndev counters from
hardware makes them precise.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device hardware provides only 32bit counters. Using these directly
causes byte counters to overflow soon. A separate nic level structure
with 64 bit counters is now used to collect incrementally all the stats
and report these counters to ethtool stats and ndev stats.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Fixes the following sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:224:5: warning:
symbol 'aq_ethtool_get_coalesce' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:245:5: warning:
symbol 'aq_ethtool_set_coalesce' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default Tx rates cause very long ISR delays on Tx.
0xff is 510us delay, giving only ~ 2000 interrupts per seconds for
Tx rings cleanup. With these settings udp tx rate was never higher than
~800Mbps on a single stream. Changing min delay to 0xF makes it
way better with ~6Gbps
TCP stream performance is almost unaffected by this change, since LSO
optimizations play important role.
CPU load is affected insignificantly by this change.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia NIC allows both TX and RX interrupt throttle rate (ITR)
management, but this was used in a very limited way via predefined
values. This patch allows to setup ITR default values via module
command line arguments and via standard ethtool coalescing settings.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That may lead to mmio resource leakage.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no much practical use from having MSIX vectors more that number
of cpus, thus cap this first with preconfigured limit, then with number
of cpus online.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing ifconfig down/up, driver did not reported carrier_off neither
in nic_stop nor in nic_start. That caused link to be visible as "up"
during couple of seconds immediately after "ifconfig up".
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Queue stat strings are cleaned up, duplicate stat name strings removed,
queue restarts counter added
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal statistics system on chip never gets reset until hardware
reboot. This is quite inconvenient in terms of ethtool statistics usage.
This patch implements incremental statistics update inside of
service callback.
Upon nic initialization, first request is done to fetch
initial stat data, current collected stat data gets cleared.
Internal statistics mailbox readout is improved to save space and
increase readability
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some spelling typos found in Kconfig files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.
This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
link changes.
- introduces new constant for minimum descriptors count required for queue
wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should inform user about wrong firmware version
by printing message in dmesg.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the HW supports up to 32 multicast filters we should
track count of multicast filters to avoid overflow.
If we attempt to add >32 multicast filter - just set NETIF_ALLMULTI flag
instead.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Igor Russkikh <Igor.Russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver choose the optimal interrupt throttling settings depends
of current link speed.
Due this bug link_status field from aq_hw is never updated and as result
always used same interrupt throttling values.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has the HW Checksum Offload bug when small
TCP patckets (with length <= 60 bytes) has wrong "checksum valid" bit.
The solution is - ignore checksum valid bit for small packets
(with length <= 60 bytes) and mark this as CHECKSUM_NONE to allow
network stack recalculate checksum itself.
Fixes: ccf9a5ed14be ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of RSS queues should be not more than numbers of CPU.
Its does not make sense to increase perfomance, and also cause problems on
some motherboards.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes datapath spinlocks which does not perform any
useful work.
Fixes: 6e70637f9f1e ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is not defined, so no need to declare it.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was introduced with commit 5a21232983 ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error status err is initialized as zero and then being checked
several times to see if it is less than zero even when it has not
been updated. It may seem that the err should be assigned to the
return code of the call to the various *offload_en_set calls and
then we check for failure, however, these functions are void and
never actually return any status.
Since these error checks are redundant we can remove these
as well as err and the error exit label err_exit.
Detected by CoverityScan, CID#1398313 and CID#1398306 ("Logically
dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the crash that happens when driver tries to collect statistics
from already released "aq_vec" object.
If adapter is in "down" state we still allow user to see statistics from HW.
V2: fixed braces around "aq_vec_free".
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Tested-by: David Arcari <darcari@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V2: using "aquantia" subsystem tag.
The command "ethtool -i ethX" should display driver name (driver: atlantic)
instead vendor name (driver: aquantia).
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reset is_gso flag when EOP reached (entire LSO packet processed).
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Context Command bit: L3 type = "0" for IPv4, "1" for IPv6.
Fixes: bab6de8fd1 ("net: ethernet: aquantia:
Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for missing initialization aq_ring header.lock spinlock.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the checksum offloads to work correctly we need to set the
packet type bit (TCP/UDP) in the TX context buffer.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Tested-by: David Arcari <darcari@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Closing/opening the adapter is not needed at all.
The new MTU settings take effect immediately.
Fixes: 97bde5c4f9 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since AQC-100/107/108 chips supports hardware checksums for RX we should indicate this
via NETIF_F_RXCSUM flag.
v1->v2: 'Signed-off-by' tag added.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the aquantia device mtu is changed the net_device structure is not
updated. As a result the ip command does not properly reflect the mtu change.
Commit 5513e16421 incorrectly assumed that __dev_set_mtu() was making the
assignment ndev->mtu = new_mtu; This is not true in the case where the driver
has a ndo_change_mtu routine.
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Cc: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).
The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().
WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
dump_stack+0x63/0x87
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
__free_irq+0x24d/0x2b0
free_irq+0x39/0x90
aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
aq_nic_stop+0xca/0xd0 [atlantic]
aq_ndev_close+0x1d/0x40 [atlantic]
__dev_close_many+0x99/0x100
__dev_close+0x67/0xb0
<snip>
Fixes: 36a4a50f40 ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix removes copying of tx biffers.
Now we use ring->buff_fing directly.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should allocate the number of pages based on the config parameter
AQ_CFG_RX_FRAME_MAX.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxd_wb->pkt_len is the total length of the packet.
If we received a large packet (with length > AQ_CFG_RX_FRAME_MAX) then we
will get multiple buffers. We need to fix the length of the last buffer.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_register should be called when everything is initialized.
Also we should use net_device->reg_state field instead own
"is_ndev_registered" flag to avoid any race.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check for a null pointer for aq_nic_ndev_alloc
instead netdev_priv.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NETDEV_TX_OK as the return value for successful transmission.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_unlock should be called if error occurred.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed superfluous initialization of err.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1)Removed unnecessary comparsion "old_mtu == new_mtu".
This check is not needed. Function aq_ndev_change_mtu wont be called
if mtu has not changed.
2)Removed extra assignment ndev->mtu = new_mtu;
This assignment already done inside __dev_set_mtu().
3)Use core MTU checking for min_mtu.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
busy_count field and is_busy flag is not needed at all.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment is not needed.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both functions aq_ring_rx_deinit() and aq_ring_tx_clean() are almost
identical aside from an additional check in the latter.
Move that check from the function into its caller and replace
aq_ring_rx_deinit() with aq_ring_rx_deinit().
By doing this also adjust the functions return value from int to void
since it can never fail.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_msix has been long deprecated, but this driver adds a new
instance. Convert it to pci_alloc_irq_vectors so that no new instance
of the deprecated function reaches mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using new link mode indices instead deprecated SUPPORTED_/ADVERTISED_
macro.
Added indication for 2500 and 5000mbit link modes (AQtion adapter already
supports these speeds).
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_mapping_error() returns 1 if there is an error and 0 if not.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Pavel Belous <pavel.s.belous@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions that support receive side scaling.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the driver interfaces required for support by the ethtool utility.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to interface with the hardware and some utility functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common functions for Atlantic hardware abstraction layer.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that handle the PCI bus interface.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to manululate the vector of receive and transmit rings.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Atlantic A0 and B0 specific functions.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for code specific to the Atlantic NIC.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of functions that interface directly with the hardware.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel.Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to support the transmit and receive ring buffers.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add files containing the functions and definitions used in common in
different functional areas.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patches to create the make and configuration files.
Signed-off-by: Alexander Loktionov <Alexander.Loktionov@aquantia.com>
Signed-off-by: Dmitrii Tarakanov <Dmitrii.Tarakanov@aquantia.com>
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <Dmitry.Bezrukov@aquantia.com>
Signed-off-by: David M. VomLehn <vomlehn@texas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
