IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Newer AMD processors have a feature to virtualize the use of the
SPEC_CTRL MSR. Presence of this feature is indicated via CPUID
function 0x8000000A_EDX[20]: GuestSpecCtrl. Hypervisors are not
required to enable this feature since it is automatically enabled on
processors that support it.
A hypervisor may wish to impose speculation controls on guest
execution or a guest may want to impose its own speculation controls.
Therefore, the processor implements both host and guest
versions of SPEC_CTRL.
When in host mode, the host SPEC_CTRL value is in effect and writes
update only the host version of SPEC_CTRL. On a VMRUN, the processor
loads the guest version of SPEC_CTRL from the VMCB. When the guest
writes SPEC_CTRL, only the guest version is updated. On a VMEXIT,
the guest version is saved into the VMCB and the processor returns
to only using the host SPEC_CTRL for speculation control. The guest
SPEC_CTRL is located at offset 0x2E0 in the VMCB.
The effective SPEC_CTRL setting is the guest SPEC_CTRL setting or'ed
with the hypervisor SPEC_CTRL setting. This allows the hypervisor to
ensure a minimum SPEC_CTRL if desired.
This support also fixes an issue where a guest may sometimes see an
inconsistent value for the SPEC_CTRL MSR on processors that support
this feature. With the current SPEC_CTRL support, the first write to
SPEC_CTRL is intercepted and the virtualized version of the SPEC_CTRL
MSR is not updated. When the guest reads back the SPEC_CTRL MSR, it
will be 0x0, instead of the actual expected value. There isn’t a
security concern here, because the host SPEC_CTRL value is or’ed with
the Guest SPEC_CTRL value to generate the effective SPEC_CTRL value.
KVM writes with the guest's virtualized SPEC_CTRL value to SPEC_CTRL
MSR just before the VMRUN, so it will always have the actual value
even though it doesn’t appear that way in the guest. The guest will
only see the proper value for the SPEC_CTRL register if the guest was
to write to the SPEC_CTRL register again. With Virtual SPEC_CTRL
support, the save area spec_ctrl is properly saved and restored.
So, the guest will always see the proper value when it is read back.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <161188100955.28787.11816849358413330720.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An SEV-ES vCPU requires additional VMCB vCPU load/put requirements. SEV-ES
hardware will restore certain registers on VMEXIT, but not save them on
VMRUN (see Table B-3 and Table B-4 of the AMD64 APM Volume 2), so make the
following changes:
General vCPU load changes:
- During vCPU loading, perform a VMSAVE to the per-CPU SVM save area and
save the current values of XCR0, XSS and PKRU to the per-CPU SVM save
area as these registers will be restored on VMEXIT.
General vCPU put changes:
- Do not attempt to restore registers that SEV-ES hardware has already
restored on VMEXIT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <019390e9cb5e93cd73014fa5a040c17d42588733.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An SEV-ES vCPU requires additional VMCB initialization requirements for
vCPU creation and vCPU load/put requirements. This includes:
General VMCB initialization changes:
- Set a VMCB control bit to enable SEV-ES support on the vCPU.
- Set the VMCB encrypted VM save area address.
- CRx registers are part of the encrypted register state and cannot be
updated. Remove the CRx register read and write intercepts and replace
them with CRx register write traps to track the CRx register values.
- Certain MSR values are part of the encrypted register state and cannot
be updated. Remove certain MSR intercepts (EFER, CR_PAT, etc.).
- Remove the #GP intercept (no support for "enable_vmware_backdoor").
- Remove the XSETBV intercept since the hypervisor cannot modify XCR0.
General vCPU creation changes:
- Set the initial GHCB gpa value as per the GHCB specification.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <3a8aef366416eddd5556dfa3fdc212aafa1ad0a2.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SEV-ES adds a new VMEXIT reason code, VMGEXIT. Initial support for a
VMGEXIT includes mapping the GHCB based on the guest GPA, which is
obtained from a new VMCB field, and then validating the required inputs
for the VMGEXIT exit reason.
Since many of the VMGEXIT exit reasons correspond to existing VMEXIT
reasons, the information from the GHCB is copied into the VMCB control
exit code areas and KVM register areas. The standard exit handlers are
invoked, similar to standard VMEXIT processing. Before restarting the
vCPU, the GHCB is updated with any registers that have been updated by
the hypervisor.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <c6a4ed4294a369bd75c44d03bd7ce0f0c3840e50.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest is running under SEV-ES, the hypervisor cannot access the
guest register state. There are numerous places in the KVM code where
certain registers are accessed that are not allowed to be accessed (e.g.
RIP, CR0, etc). Add checks to prevent register accesses and add intercept
update support at various points within the KVM code.
Also, when handling a VMGEXIT, exceptions are passed back through the
GHCB. Since the RDMSR/WRMSR intercepts (may) inject a #GP on error,
update the SVM intercepts to handle this for SEV-ES guests.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[Redo MSR part using the .complete_emulated_msr callback. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the GHCB accessor functions to add functions for retrieve GHCB
fields by name. Update existing code to use the new accessor functions.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <664172c53a5fb4959914e1a45d88e805649af0ad.1607620209.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new intercept bits have been added in vmcb control area to support
few more interceptions. Here are the some of them.
- INTERCEPT_INVLPGB,
- INTERCEPT_INVLPGB_ILLEGAL,
- INTERCEPT_INVPCID,
- INTERCEPT_MCOMMIT,
- INTERCEPT_TLBSYNC,
Add a new intercept word in vmcb_control_area to support these instructions.
Also update kvm_nested_vmrun trace function to support the new addition.
AMD documentation for these instructions is available at "AMD64
Architecture Programmer’s Manual Volume 2: System Programming, Pub. 24593
Rev. 3.34(or later)"
The documentation can be obtained at the links below:
Link: https://www.amd.com/system/files/TechDocs/24593.pdf
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985251547.11252.16994139329949066945.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the intercepts to one array of 32 bit vectors in
vmcb_control_area. This makes it easy for future intercept vector
additions. Also update trace functions.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985250813.11252.5736581193881040525.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify intercept_exceptions to generic intercepts in vmcb_control_area. Use
the generic vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept to
set/clear/test the intercept_exceptions bits.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985250037.11252.1361972528657052410.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify intercept_dr to generic intercepts in vmcb_control_area. Use
the generic vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
to set/clear/test the intercept_dr bits.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985249255.11252.10000868032136333355.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change intercept_cr to generic intercepts in vmcb_control_area.
Use the new vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
where applicable.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985248506.11252.9081085950784508671.stgit@bmoger-ubuntu>
[Change constant names. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is in preparation for the future intercept vector additions.
Add new functions vmcb_set_intercept, vmcb_clr_intercept and vmcb_is_intercept
using kernel APIs __set_bit, __clear_bit and test_bit espectively.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <159985247876.11252.16039238014239824460.stgit@bmoger-ubuntu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the shorthand to make it more readable.
No functional changes.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-5-joro@8bytes.org
Building a correct GHCB for the hypervisor requires setting valid bits
in the GHCB. Simplify that process by providing accessor functions to
set values and to update the valid bitmap and to check the valid bitmap
in KVM.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-4-joro@8bytes.org
Extend the vmcb_safe_area with SEV-ES fields and add a new
'struct ghcb' which will be used for guest-hypervisor communication.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-3-joro@8bytes.org
Allow placing the VMCB structs on the stack or in other structs without
wasting too much space. Add BUILD_BUG_ON as a quick safeguard against typos.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The RDPRU instruction gives the guest read access to the IA32_APERF
MSR and the IA32_MPERF MSR. According to volume 3 of the APM, "When
virtualization is enabled, this instruction can be intercepted by the
Hypervisor. The intercept bit is at VMCB byte offset 10h, bit 14."
Since we don't enumerate the instruction in KVM_SUPPORTED_CPUID,
intercept it and synthesize #UD.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Drew Schmitt <dasch@google.com>
Reviewed-by: Jacob Xu <jacobhxu@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recently the minimum required version of binutils was changed to 2.20,
which supports all SVM instruction mnemonics. The patch removes
all .byte #defines and uses real instruction mnemonics instead.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds the support for pause filtering threshold. This feature
support is indicated by CPUID Fn8000_000A_EDX. See AMD APM Vol 2 Section
15.14.4 Pause Intercept Filtering for more details.
In this mode, a 16-bit pause filter threshold field is added in VMCB.
The threshold value is a cycle count that is used to reset the pause
counter. As with simple pause filtering, VMRUN loads the pause count
value from VMCB into an internal counter. Then, on each pause instruction
the hardware checks the elapsed number of cycles since the most recent
pause instruction against the pause Filter Threshold. If the elapsed cycle
count is greater than the pause filter threshold, then the internal pause
count is reloaded from VMCB and execution continues. If the elapsed cycle
count is less than the pause filter threshold, then the internal pause
count is decremented. If the count value is less than zero and pause
intercept is enabled, a #VMEXIT is triggered. If advanced pause filtering
is supported and pause filter threshold field is set to zero, the filter
will operate in the simpler, count only mode.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Define the SEV enable bit for the VMCB control structure. The hypervisor
will use this bit to enable SEV in the guest.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Currently the nested_ctl variable in the vmcb_control_area structure is
used to indicate nested paging support. The nested paging support field
is actually defined as bit 0 of the field. In order to support a new
feature flag the usage of the nested_ctl and nested paging support must
be converted to operate on a single bit.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the Virtual GIF feature. This is done by setting bit 25 at position
60h in the vmcb.
With this feature enabled, the processor uses bit 9 at position 60h as the
virtual GIF when executing STGI/CLGI instructions.
Since the execution of STGI by the L1 hypervisor does not cause a return to
the outermost (L0) hypervisor, the enable_irq_window and enable_nmi_window
are modified.
The IRQ window will be opened even if GIF is not set, under the assumption
that on resuming the L1 hypervisor the IRQ will be held pending until the
processor executes the STGI instruction.
For the NMI window, the STGI intercept is set. This will assist in opening
the window only when GIF=1.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable the Virtual VMLOAD VMSAVE feature. This is done by setting bit 1
at position B8h in the vmcb.
The processor must have nested paging enabled, be in 64-bit mode and
have support for the Virtual VMLOAD VMSAVE feature for the bit to be set
in the vmcb.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Rename the lbr_ctl variable to better reflect the purpose of the field -
provide support for virtualization extensions.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The lbr_ctl variable in the vmcb control area is used to enable or
disable Last Branch Record (LBR) virtualization. However, this is to be
done using only bit 0 of the variable. To correct this and to prepare
for a new feature, change the current usage to work only on a particular
bit.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This patch introduces AVIC-related data structure, and AVIC
initialization code.
There are three main data structures for AVIC:
* Virtual APIC (vAPIC) backing page (per-VCPU)
* Physical APIC ID table (per-VM)
* Logical APIC ID table (per-VM)
Currently, AVIC is disabled by default. Users can manually
enable AVIC via kernel boot option kvm-amd.avic=1 or during
kvm-amd module loading with parameter avic=1.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
[Avoid extra indentation (Boris). - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Exporting KVM exit information to userspace to be consumed by perf.
Signed-off-by: Dong Hao <haodong@linux.vnet.ibm.com>
[ Dong Hao <haodong@linux.vnet.ibm.com>: rebase it on acme's git tree ]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Runzhen Wang <runzhen@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1347870675-31495-2-git-send-email-haodong@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In case of a nested page fault or an intercepted #PF newer SVM
implementations provide a copy of the faulting instruction bytes
in the VMCB.
Use these bytes to feed the instruction emulator and avoid the costly
guest instruction fetch in this case.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Newer SVM implementations provide the GPR number in the VMCB, so
that the emulation path is no longer necesarry to handle CR
register access intercepts. Implement the handling in svm.c and
use it when the info is provided.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch implements the xsetbv intercept to the AMD part
of KVM. This makes AVX usable in a save way for the guest on
AVX capable AMD hardware.
The patch is tested by using AVX in the guest and host in
parallel and checking for data corruption. I also used the
KVM xsave unit-tests and they all pass.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the new flush-by-asid of upcoming AMD
processors to the KVM-AMD module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the infrastructure for the implementation of
the individual clean-bits.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch wraps changes to the DRx intercepts of SVM into
seperate functions to abstract nested-svm better and prepare
the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch wraps changes to the CRx intercepts of SVM into
seperate functions to abstract nested-svm better and prepare
the implementation of the vmcb-clean-bits feature.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When a fault triggers a task switch, the error code, if existent, has to
be pushed on the new task's stack. Implement the missing bits.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On SVM we set the instruction length of skipped instructions
to hard-coded, well known values, which could be wrong when (bogus,
but valid) prefixes (REX, segment override) are used.
Newer AMD processors (Fam10h 45nm and better, aka. PhenomII or
AthlonII) have an explicit NEXTRIP field in the VMCB containing the
desired information.
Since it is cheap to do so, we use this field to override the guessed
value on newer processors.
A fix for older CPUs would be rather expensive, as it would require
to fetch and partially decode the instruction. As the problem is not
a security issue and needs special, handcrafted code to trigger
(no compiler will ever generate such code), I omit a fix for older
CPUs.
If someone is interested, I have both a patch for these CPUs as well as
demo code triggering this issue: It segfaults under KVM, but runs
perfectly on native Linux.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch implements the emulation of the vm_cr msr for
nested svm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of selecting TS and MP as the comments say, the macro included TS and
PE. Luckily the macro is unused now, but fix in order to save a few hours of
debugging from anyone who attempts to use it.
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
New AMD processors (Family 0x10 models 8+) support the Pause
Filter Feature. This feature creates a new field in the VMCB
called Pause Filter Count. If Pause Filter Count is greater
than 0 and intercepting PAUSEs is enabled, the processor will
increment an internal counter when a PAUSE instruction occurs
instead of intercepting. When the internal counter reaches the
Pause Filter Count value, a PAUSE intercept will occur.
This feature can be used to detect contended spinlocks,
especially when the lock holding VCPU is not scheduled.
Rescheduling another VCPU prevents the VCPU seeking the
lock from wasting its quantum by spinning idly.
Experimental results show that most spinlocks are held
for less than 1000 PAUSE cycles or more than a few
thousand. Default the Pause Filter Counter to 3000 to
detect the contended spinlocks.
Processor support for this feature is indicated by a CPUID
bit.
On a 24 core system running 4 guests each with 16 VCPUs,
this patch improved overall performance of each guest's
32 job kernbench by approximately 3-5% when combined
with a scheduler algorithm thati caused the VCPU to
sleep for a brief period. Further performance improvement
may be possible with a more sophisticated yield algorithm.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
There is no need to skip instruction if the reason for a task switch
is a task gate in IDT and access to it is caused by an external even.
The problem is currently solved only for VMX since there is no reliable
way to skip an instruction in SVM. We should emulate it instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
MSR_EFER_SVME_MASK, MSR_VM_CR and MSR_VM_HSAVE_PA are set in KVM
specific headers. Linux does have nice header files to collect
EFER bits and MSR IDs, so IMHO we should put them there.
While at it, I also changed the naming scheme to match that
of the other defines.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
svm.h will be used by core code that is independent of KVM, so I am
moving it outside the arch/x86/kvm directory.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
