IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[patch] x86: Trivial printk fix in efi.c
The following line is lacking a space between "memdesc" and "doesn't".
"Kernel-defined memdescdoesn't match the one from EFI!"
Fixed the printk by adding a space.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 00c5372d37a78990c1530184a9c792ee60a30067 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56ca09a467fbbe5229bc68627f7445be
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56ca09a467fbbe5229bc68627f7445be
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix failure to shutdown with CPU hotplug
powerpc: Fix PCI in Holly device tree
The number of BIOSes that have an option to enable the IOMMU, or fix
anything about its configuration, is vanishingly small. There's no good
reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Export set_memory_ro() and set_memory_rw() calls for use by drivers that need
to have more debug information about who might be writing to memory space.
this was initially developed for use while debugging a memory corruption
problem with e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I tracked down the shutdown regression to CPUs not dying
when being shut down during power-off. This turns out to
be due to the system_state being SYSTEM_POWER_OFF, which
this code doesn't take as a valid state for shutting off
CPUs in.
This has never made sense to me, but when I added hotplug
code to implement hibernate I only "made it work" and did
not question the need to check the system_state. Thomas
Gleixner helped me dig, but the only thing we found is
that it was added with the original commit that added CPU
hotplug support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Delay exit to make sure we can actually get the optimal result in as
many cases as possible.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Initial fix for making sure that we can access percpu variables
in all C code (commit: 10617bbe84628eb18ab5f723d3ba35005adde143)
inadvertantly allocated the memory in the "percpu" section of
the vmlinux ELF executable. This confused kexec/dump.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,tty: Fix tty polling search to use name correctly
kgdb, x86_64: fix PS CS SS registers in gdb serial
kgdb, x86_64: gdb serial has BX and DX reversed
kgdb, x86, arm, mips, powerpc: ignore user space single stepping
kgdb: could not write to the last of valid memory with kgdb
v2: should check with half of range0 size instead of chunk_size
So don't have silly big hole.
in hpa's case we could auto detect instead of adding mtrr_chunk_size in
command line.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add mtrr_cleanup_debug to print out more info about layout
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
change back chunksize max to 2g
otherwise will get strange layout in 2G ram system like
0 - 4g WB, 2040M - 2048M UC, 2048M - 4G NC
instead of
0 - 2g WB, 2040M - 2048M UC
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch defines pcibios_map_irq() and pcibios_plat_dev_init() for
the BCM47xx platform.
It fixes the regression introduced by commit
aab547ce0d1493d400b6468c521a0137cd8c1edf.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_map_irq is no way of returning an error but on IP27 an interrupt
is possibly not routable when running out of resources. So do the
interrupt routing at pcibios_enable_device time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Brownell <david-b@pacbell.net> wrote:
> The problem is that "value" is zero-or-nonzero.
> This code wrongly assumes it's zero-or-one.
> Possible fix: "((!!value) << gpio)".
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As far as I know no M32R hardware actually has ISA slots.
And ISA drivers don't compile on M32R.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Remove the unused NOHIGHMEM option.
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Delete ARM's own cnt32_to_63.h as the copy in include/linux/ should now be
used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 the gdb serial register structure defines the PS (also known
as eflags), CS and SS registers as 4 bytes entities.
This patch splits the x86_64 regnames enum into a 32 and 64 version to
account for the 32 bit entities in the gdb serial packets.
Also the program counter is properly filled in for the sleeping
threads.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On the x86 arch, user space single step exceptions should be ignored
if they occur in the kernel space, such as ptrace stepping through a
system call.
First check if it is kgdb that is executing a single step, then ensure
it is not an accidental traversal into the user space, while in kgdb,
any other time the TIF_SINGLESTEP is set, kgdb should ignore the
exception.
On x86, arm, mips and powerpc, the kgdb_contthread usage was
inconsistent with the way single stepping is implemented in the kgdb
core. The arch specific stub should always set the
kgdb_cpu_doing_single_step correctly if it is single stepping. This
allows kgdb to correctly process an instruction steps if ptrace
happens to be requesting an instruction step over a system call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: prevent stale state of c1e_mask across CPU offline/online, fix
Make sched_clock() report time since boot rather than time since last
timer interrupt.
Make sched_clock() expand and scale the 32-bit TSC value running at
IOCLK speed (~33MHz) to a 64-bit nanosecond counter, using cnt32_to_63()
acquired from the ARM arch and without using slow DIVU instructions
every call.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move asm-arm/cnt32_to_63.h to include/linux/ so that MN10300 can make
use of it too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boardrev is always treated as a u32 everywhere else, no reason to
byteswap the 0xc2 value. The only use is to print out if it is
a prerelease board, the test being:
(olpc_platform_info.boardrev & 0xf) < 8
Which is currently always true as be32_to_cpu(0xc2) & 0xf = 0
but I doubt that was the intention here. The consequences of the bug
are pretty minor though (incorrect boardrev displayed in dmesg when
ofw support not configured)
Also annotate the temporary used to read the boardrev in the ofw
case.
The confusion was noticed by Sparse:
arch/x86/kernel/olpc.c:206:32: warning: cast to restricted __be32
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/ptrace.c:763:29: warning: Using plain integer as NULL pointer
arch/x86/kernel/ptrace.c:777:46: warning: Using plain integer as NULL pointer
arch/x86/kernel/ptrace.c:1115:45: warning: Using plain integer as NULL pointer
arch/x86/kernel/ds.c:482:26: warning: Using plain integer as NULL pointer
arch/x86/kernel/ds.c:487:25: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The OLPC doesn't support APM but also doesn't have DMI, so we can't detect
and disable it based on DMI data. So, just disable based on machine_is_olpc()
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
