IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Change the PS3 hotplug memory routine ps3_mm_add_memory() from
a core_initcall to a device_initcall.
core_initcall routines run before the powerpc topology_init()
startup routine, which is a subsys_initcall, resulting in
failure of ps3_mm_add_memory() when CONFIG_NUMA=y. When
ps3_mm_add_memory() fails the system will boot with just the
128 MiB of boot memory
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the powerpc NUMA reserve bootmem page selection logic.
commit 8f64e1f2d1e09267ac926e15090fd505c1c0cbcb (powerpc: Reserve
in bootmem lmb reserved regions that cross NUMA nodes) changed
the logic for how the powerpc LMB reserved regions were converted
to bootmen reserved regions. As the folowing discussion reports,
the new logic was not correct.
mark_reserved_regions_for_nid() goes through each LMB on the
system that specifies a reserved area. It searches for
active regions that intersect with that LMB and are on the
specified node. It attempts to bootmem-reserve only the area
where the active region and the reserved LMB intersect. We
can not reserve things on other nodes as they may not have
bootmem structures allocated, yet.
We base the size of the bootmem reservation on two possible
things. Normally, we just make the reservation start and
stop exactly at the start and end of the LMB.
However, the LMB reservations are not aware of NUMA nodes and
on occasion a single LMB may cross into several adjacent
active regions. Those may even be on different NUMA nodes
and will require separate calls to the bootmem reserve
functions. So, the bootmem reservation must be trimmed to
fit inside the current active region.
That's all fine and dandy, but we trim the reservation
in a page-aligned fashion. That's bad because we start the
reservation at a non-page-aligned address: physbase.
The reservation may only span 2 bytes, but that those bytes
may span two pfns and cause a reserve_size of 2*PAGE_SIZE.
Take the case where you reserve 0x2 bytes at 0x0fff and
where the active region ends at 0x1000. You'll jump into
that if() statment, but node_ar.end_pfn=0x1 and
start_pfn=0x0. You'll end up with a reserve_size=0x1000,
and then call
reserve_bootmem_node(node, physbase=0xfff, size=0x1000);
0x1000 may not be on the same node as 0xfff. Oops.
In almost all the vm code, end_<anything> is not inclusive.
If you have an end_pfn of 0x1234, page 0x1234 is not
included in the range. Using PFN_UP instead of the
(>> >> PAGE_SHIFT) will make this consistent with the other VM
code.
We also need to do math for the reserved size with physbase
instead of start_pfn. node_ar.end_pfn << PAGE_SHIFT is
*precisely* the end of the node. However,
(start_pfn << PAGE_SHIFT) is *NOT* precisely the beginning
of the reserved area. That is, of course, physbase.
If we don't use physbase here, the reserve_size can be
made too large.
From: Dave Hansen <dave@linux.vnet.ibm.com>
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com> Tested on PS3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix _PAGE_CHG_MASK so that pte_modify() does not affect the _PAGE_SPECIAL bit.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: Flush the lazy MMU only once
Pending mmu updates only need to be flushed once to bring the
in-memory pagetable state up to date.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Catch cases where lazy MMU state is active in a preemtible context
arch_flush_lazy_mmu_cpu() has been changed to disable preemption so
the checks in enter/leave will never trigger. Put the preemtible()
check into arch_flush_lazy_mmu_cpu() to catch such cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: avoid access to percpu vars in preempible context
They are intended to be used whenever there's the possibility
that there's some stale state which is going to be overwritten
with a queued update, or to force a state change when we may be
in lazy mode. Either way, we could end up calling it with
preemption enabled, so wrap the functions in their own little
preempt-disable section so they can be safely called in any
context (though preemption should never be enabled if we're actually
in a lazy state).
(Move out of line to avoid #include dependencies.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jeff Mahoney reported:
> With Suse's hwinfo tool, on -tip:
> WARNING: at arch/x86/mm/pat.c:637 reserve_pfn_range+0x5b/0x26d()
reserve_pfn_range() is not tracking the memory range below 1MB
as non-RAM and as such is inconsistent with similar checks in
reserve_memtype() and free_memtype()
Rename the pagerange_is_ram() to pat_pagerange_is_ram() and add the
"track legacy 1MB region as non RAM" condition.
And also, fix reserve_pfn_range() to return -EINVAL, when the pfn
range is RAM. This is to be consistent with this API design.
Reported-and-tested-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix race leading to crash under KVM and Xen
The CPA code may be called while we're in lazy mmu update mode - for
example, when using DEBUG_PAGE_ALLOC and doing a slab allocation
in an interrupt handler which interrupted a lazy mmu update. In this
case, the in-memory pagetable state may be out of date due to pending
queued updates. We need to flush any pending updates before inspecting
the page table. Similarly, we must explicitly flush any modifications
CPA may have made (which comes down to flushing queued operations when
flushing the TLB).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix TIMER_ABSTIME for process wide cpu timers
timers: split process wide cpu clocks/timers, fix
x86: clean up hpet timer reinit
timers: split process wide cpu clocks/timers, remove spurious warning
timers: split process wide cpu clocks/timers
signal: re-add dead task accumulation stats.
x86: fix hpet timer reinit for x86_64
sched: fix nohz load balancer on cpu offline
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
Ptrace_detach() races with __ptrace_unlink() if the traced task is
reaped while detaching. This might cause a double-free of the BTS
buffer.
Change the ptrace_detach() path to only do the memory accounting in
ptrace_bts_detach() and leave the buffer free to ptrace_bts_untrace()
which will be called from __ptrace_unlink().
The fix follows a proposal from Oleg Nesterov.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The vdso_per_cpu_data entry in the lowcore structure uses __u32
instead of __u64. If the data page is above 4GB the pointer is
truncated and the kernel crashes.
Reported-by: Mijo Safradin <mijo@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The constraint used for retrieving and restoring the parent function
pointer is incorrect. The parent variable is a pointer, and the
address of the pointer is modified by the asm statement and not
the pointer itself. It is incorrect to pass it in as an output
constraint since the asm will never update the pointer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The following commit:
commit 64b3d0e8122b422e879b23d42f9e0e8efbbf9744
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Thu Dec 18 19:13:51 2008 +0000
powerpc/mm: Rework usage of _PAGE_COHERENT/NO_CACHE/GUARDED
broke setting of the _PAGE_COHERENT bit in the PPC HW PTE. Since we now
actually set _PAGE_COHERENT in the Linux PTE we shouldn't be clearing it
out before we propogate it to the PPC HW PTE.
Reported-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] AACI: timeout will reach -1
[ARM] Storage class should be before const qualifier
[ARM] pxa: stop and disable IRQ for each DMA channels at startup
[ARM] pxa: make more SSCR0 bit definitions visible on multiple processors
[ARM] pxa: fix missing of __REG() definition for ac97 registers access
[ARM] pxa: fix NAND and MMC clock initialization for pxa3xx
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Add missing sparsemem.h include
powerpc/pci: mmap anonymous memory when legacy_mem doesn't exist
powerpc/cell: Add missing #include for oprofile
powerpc/ftrace: Fix math to calculate offset in TOC
powerpc: Don't emulate mr. instructions
powerpc/fsl-booke: Fix mapping functions to use phys_addr_t
arch/powerpc: Eliminate double sizeof
powerpc/cpm2: Fix set interrupt type
powerpc/83xx: Fix TSEC0 workability on MPC8313E-RDB boards
powerpc/83xx: Fix missing #{address,size}-cells in mpc8313erdb.dts
powerpc/83xx: Build breakage for CONFIG_PM but no CONFIG_SUSPEND
Impact: fix to prevent a kernel crash on fault
If for some reason the pointer to the parent function on the
stack takes a fault, the fix up code will not return back to
the original faulting code. This can lead to unpredictable
results and perhaps even a kernel panic.
A fault should not happen, but if it does, we should simply
disable the tracer, warn, and continue running the kernel.
It should not lead to a kernel crash.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
In i8237A_resume(), when resetting the DMA controller, the parameters to
dma_outb() were mixed up.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
[ cleaned up the file a tiny bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning of the
declaration specifiers in a declaration is an obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new legacy_mem file in sysfs is causing problems with X on machines
that don't support legacy memory access. The way I initially implemented
it, we would fail with -ENXIO when trying to mmap it, thus exposing to
X that we do support the API but there is no legacy memory.
Unfortunately, X poor error handling is causing it to fail to start when
it gets this error.
This implements a workaround hack that instead maps anonymous memory
instead (using shmem if VM_SHARED is set, just like /dev/zero does).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/oprofile/cell/spu_profiler.c is missing a asm/time.h
include which is required for ppc_proc_freq. This can cause compile
failures for some config combinations.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: fix dynamic ftrace with large modules in PPC64
The math to calculate the offset into the TOC that is taken from reading
the trampoline is incorrect. The bottom half of the offset is a signed
extended short. The current code was using an OR to create the offset
when it should have been using an addition.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently emulate_step() emulates mr. instructions without updating cr0
and this can be disastrous. Don't emulate mr.
This bug has been around for a while, but I am not sure if its a worthy
-stable candidate. I'll leave it to Ben do decide.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixed v_mapped_by_tlbcam() and p_mapped_by_tlbcam() to use phys_addr_t
instead of unsigned long. In 36-bit physical mode we really need these
functions to deal with phys_addr_t when trying to match a physical
address or when returning one.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
do_device_not_available() is the handler for #NM and it declares that
it takes a unsigned long and calls math_emu(), which takes a long
argument and surprisingly expects the stack frame starting at the zero
argument would match struct math_emu_info, which isn't true regardless
of configuration in the current code.
This patch makes do_device_not_available() take struct pt_regs like
other exception handlers and initialize struct math_emu_info with
pointer to it and pass pointer to the math_emu_info to math_emulate()
like normal C functions do. This way, unless gcc makes a copy of
struct pt_regs in do_device_not_available(), the register frame is
correctly accessed regardless of kernel configuration or compiler
used.
This doesn't fix all math_emu problems but it at least gets it
somewhat working.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Get transition latency from ACPI _PSS table
[CPUFREQ] Make ignore_nice_load setting of ondemand work as expected.
Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).
Dummy it out to return 0 on other architectures.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
* Come on, struct info? s/struct info/struct math_emu_info/
* Use struct pt_regs and kernel_vm86_regs instead of defining its own
register frame structure.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: dump the correct %gs into a.out core dump
aout_dump_thread() read %gs but didn't include it in core dump. Fix
it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 6194ba6ff6ccf8d5c54c857600843c67aa82c407 ("x86: don't special-case
pmd allocations as much") made changes to the way we handle pmd allocations,
and while doing that it dropped a call to paravirt_release_pd on the
pgd page from the pgd_dtor code path.
As a result of this missing release, the hypervisor is now unaware of the
pgd page being freed, and as a result it ends up tracking this page as a
page table page.
After this the guest may start using the same page for other purposes, and
depending on what use the page is put to, it may result in various performance
and/or functional issues ( hangs, reboots).
Since this release is only required for VMI, I now release the pgd page from
the (vmi)_pgd_free hook.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For Intel 7400 series CPUs, the recommendation is to use a clflush on the
monitored address just before monitor and mwait pair [1].
This clflush makes sure that there are no false wakeups from mwait when the
monitored address was recently written to.
[1] "MONITOR/MWAIT Recommendations for Intel Xeon Processor 7400 series"
section in specification update document of 7400 series
http://download.intel.com/design/xeon/specupdt/32033601.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is based upon a report from Chris Torek and his initial patch.
From Chris's report:
--------------------
This came up in testing kgdb, using the built-in tests -- turn
on CONFIG_KGDB_TESTS, then
echo V1 > /sys/module/kgdbts/parameters/kgdbts
-- but it would affect using kgdb if you were debugging and looking
at bad pointers.
--------------------
When we get a copy_{from,to}_user() request and the %asi is set to
something other than ASI_AIUS (which is userspace) then we branch off
to a routine called memcpy_user_stub(). It just does a straight
memcpy since we are copying from kernel to kernel in this case.
The logic was that since source and destination are both kernel
pointers we don't need to have exception checks.
But for what probe_kernel_{read,write}() is trying to do, we have to
have the checks, otherwise things like kgdb bad kernel pointer
accesses don't do the right thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of a suggestion made by Chris Torek:
--------------------
Something else I noticed in passing: the EX and EX_LD/EX_ST macros
scattered throughout the various .S files make a fair bit of .fixup
code, all of which does the same thing. At the cost of one symbol
in copy_in_user.S, you could just have one common two-instruction
retl-and-mov-1 fixup that they all share.
--------------------
The following is with a defconfig build:
text data bss dec hex filename
3972767 344024 584449 4901240 4ac978 vmlinux.orig
3968887 344024 584449 4897360 4aba50 vmlinux
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: make the PM core more careful with drivers using the new PM framework
PCI PM: Read power state from device after trying to change it on resume
PCI PM: Do not disable and enable bridges during suspend-resume
PCI: PCIe portdrv: Simplify suspend and resume
PCI PM: Fix saving of device state in pci_legacy_suspend
PCI PM: Check if the state has been saved before trying to restore it
PCI PM: Fix handling of devices without drivers
PCI: return error on failure to read PCI ROMs
PCI: properly clean up ASPM link state on device remove
One of my past fixes to this code introduced a different new bug.
When using 32-bit "int $0x80" entry for a bogus syscall number,
the return value is not correctly set to -ENOSYS. This only happens
when neither syscall-audit nor syscall tracing is enabled (i.e., never
seen if auditd ever started). Test program:
/* gcc -o int80-badsys -m32 -g int80-badsys.c
Run on x86-64 kernel.
Note to reproduce the bug you need auditd never to have started. */
#include <errno.h>
#include <stdio.h>
int
main (void)
{
long res;
asm ("int $0x80" : "=a" (res) : "0" (99999));
printf ("bad syscall returns %ld\n", res);
return res != -ENOSYS;
}
The fix makes the int $0x80 path match the sysenter and syscall paths.
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Roland McGrath <roland@redhat.com>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
@@
type T;
@@
- sizeof (
sizeof (T)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a simple change to correct problems when using set_irq_type
on platforms using CPM2. This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.
On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: Paul Bilke <paul@conspiracy.net>
Reviewed-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
