IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Nearly every boot with a Lenovo P14s is showing
acp_pdm_mach acp_pdm_mach.0: snd_soc_register_card(acp) failed: -517
This isn't useful to a user, especially as probing will run again.
Use the dev_err_probe helper to hide the deferrerd probing messages.
CC: markpearson@lenovo.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210722132731.13264-1-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA driver stop sequence should be invoked first before invoking I2S
controller driver stop sequence for Stoneyridge platform.
Enable stop_dma_first flag for cz_dai_7219_98357 dai link structure.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210722130328.23796-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vangogh ACP5x drivers can be built by selecting necessary
kernel config option.
The patch enables build support of the same.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-13-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Vangogh I2S controller driver to support two I2S controller
instances.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-9-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Whenever audio data equal to the I2S FIFO watermark level are
produced/consumed, interrupt is generated.
Acknowledge the interrupt.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-7-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP5.x IP has multiple I2S controllers and DMA controller.
Create platform devices for I2S HS controller instance, I2S SP controller
instance and DMA controller.
Pass PCI resources like MMIO, irq to these platform devices.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-5-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP is a PCI audio device.
This patch adds PCI driver to bind to this device and get
PCI resources.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add register header for ACP5x IP in Vangogh platform.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210721180430.11571-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS2505/TAS2521 does support only three processing block options, unlike
TLV320AIC32x4 which supports 25. This is documented in TI slau472 2.5.1.2
Processing Blocks and Page 0 / Register 60: DAC Instruction Set - 0x00 / 0x3C.
Limit the Processing Blocks maximum value to 3 on TAS2505/TAS2521 and select
processing block PRB_P1 always, because for the configuration of teh codec
implemented in this driver, this is the best quality option.
Fixes: b4525b6196cd7 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210720200348.182139-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust the threshold of headset button volume+ to fix
the wrong button detection issue with some brand headsets.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20210721133121.12333-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With SND_SOC_ALL_CODECS=y and SND_SOC_WCD938X_SDW=m, there is a link
error from a reverse dependency, since the built-in codec driver calls
into the modular soundwire back-end:
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_free':
wcd938x.c:(.text+0x2c0): undefined reference to `wcd938x_sdw_free'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_hw_params':
wcd938x.c:(.text+0x2f6): undefined reference to `wcd938x_sdw_hw_params'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_codec_set_sdw_stream':
wcd938x.c:(.text+0x332): undefined reference to `wcd938x_sdw_set_sdw_stream'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_tx_swr_ctrl':
wcd938x.c:(.text+0x23de): undefined reference to `wcd938x_swr_get_current_bank'
x86_64-linux-ld: sound/soc/codecs/wcd938x.o: in function `wcd938x_bind':
wcd938x.c:(.text+0x2579): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x25a1): undefined reference to `wcd938x_sdw_device_get'
x86_64-linux-ld: wcd938x.c:(.text+0x262a): undefined reference to `__devm_regmap_init_sdw'
Work around this using two small hacks: An added Kconfig dependency
prevents the main driver from being built-in when soundwire support
itself is a loadable module to allow calling devm_regmap_init_sdw(),
and a Makefile trick links the wcd938x-sdw backend as built-in
if needed to solve the dependency between the two modules.
Fixes: 045442228868 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721150510.1837221-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of fixes for ASoC that have come in since the merge window,
all driver specific. There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmD4WP0ACgkQJNaLcl1U
h9B2jgf/Xrdc5XdlyICwwyzg5knFNzrj8T5EWDObHRdygPKVidBB45WEK9fLneDq
OCJi4up2SE6aVV0cTjmG9cSfBNP9SUwpVswDimqUQtv/qZDWgNpa6ZIxuzwPk4Rb
BVDTO9BKHOe7JCahIzHxJj0Q7Zstiz6V2C78LAJn2pJm6yzHiWb9ePjeUNvf+9vj
WpPDj20DpvnYjUJ37qvFbj7D+S155X40c3xojHnYFqIG+gJtuwHl3uiklWZrDDON
xwVvpRNQaTX/5PdZ2U/AajTkun98BkqrS6Fpo5mZTjuu2WYqWiRDQTDZbVIGsnLz
iHRiV2pncY68dYkNlQWlSMQ5nNEeHA==
=fKOW
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.14-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.14
A collection of fixes for ASoC that have come in since the merge window,
all driver specific. There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.
The same quirk is used for LAPBC510 and LAPBC710 skews who use the
same audio design, with an RT711 headset codec using JD1 mode and one
RT1308 amplifier, along with 4 DMICs.
BugLink: https://github.com/thesofproject/linux/issues/3049
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210719233248.557923-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the J721E_AUDIO_DOMAIN_* from defines to enum to make it possible
to extend the number of domains in the future.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-4-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During probe the parent_clk_id is set to -1 which should not be used to
array index within hsdiv_rates[].
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-3-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of an error within j721e_audio_startup() the domain->active must
be decremented to avoid unbalanced counter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-2-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
port_map field was added prior to adding static port map support in soundwire.
This makes port_map array in struct wcd938x_sdw_priv redundant and unused,
so remove this.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210716105612.5284-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
While using the DMIC recording, the garbled data will be captured by the
DMIC. It is caused by the critical power of PLL closed in the jack detect
function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Link: https://lore.kernel.org/r/20210716085853.20170-1-oder_chiou@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For Stoneyridge platform, it is required to invoke DMA driver stop
first rather than invoking DWC I2S controller stop.
Enable dai_link structure stop_dma_fist flag to reverse the stop
sequence.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210716123015.15697-2-vijendar.mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On stream stop, currently CPU DAI stop sequence invoked first
followed by DMA. For Few platforms, it is required to stop the
DMA first before stopping CPU DAI.
Introduced new flag in dai_link structure for reordering stop sequence.
Based on flag check, ASoC core will re-order the stop sequence.
Fixes: 4378f1fbe92405 ("ASoC: soc-pcm: Use different sequence for start/stop trigger")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210716123015.15697-1-vijendar.mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire registers are only accessable after sdw components are succesfully
binded. Setup irqs at that point instead of doing at probe.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210716105735.6073-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The for-loop is not indented enough and needs one more level
of indentation. Add in the indentation across the block of code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210709152424.460446-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for SoundWire mockup devices. The configurations assume the
same topology as the CML SoundWire devices and can be used to test the
SOF firmware on a development board (RVP, UpExtreme) without any
hardware connected.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the same idea as for CNL/UpExtreme and add mockup test
first. They will only be selected if the SSDT is modified to add such
mockup devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for two configurations with SoundWire mockup devices that
emulate the two CometLake configurations with one and two amps. This
patch helps test the SOF firmware on an UpExtreme board without any
hardware connected, e.g. by doing a loopback of the playback stream on
capture streams.
The mapping of the partIDs is as follows:
0xAAAA: generic full-duplex codec (not currently used)
0xAA55: headset codec (mock-up of RT711/RT5682) - full-duplex
0x55AA: amplifier (mock-up of RT1308/RT1316/Maxim 98373) - playback
with IV sense feedback
0x5555: mic codec (mock-up of RT715) - capture-only
The tables are added in a separate file to allow for mockup codecs to be
added on other platforms, but the mapping to specific topologies
remains platform-specific.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To test the host controller and bus management code, it is currently
required to have a physical SoundWire peripheral attached to the
bus. To help with pre-silicon or early hardware enablement, it would
be very useful to have a SoundWire 'mockup' device that is exposed in
platform firmware but does not drive any signal on the bus.
This is different to the existing ASoC 'dummy' codec uses for I2S/TDM,
the SoundWire spec makes it clear that a device that is not attached
to the bus is not permitted to interact with the bus, be it for
command/control or data.
This patch exposes a 'mockup' device, with a minimalist driver, with 4
partID values reserved by Intel for such test configurations. The
mockup device exposes one full-duplex DAI based on 2 ports (DP1 for
playback and DP8 for capture). The capture data port is just virtual,
such a mockup device is prevented by the SoundWire specification from
presenting any data generated by a Source port without being Attached.
All the callbacks exposed by the SoundWire Slave interface are
populated, even if they just return immediately. This is intentional
to describe what a minimal codec driver should do and implement and
help new codec vendors provide support for their devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADL RVP uses different circuits for jack detection, hence
adding external resister 100k mode.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: jairaj arava <jairaj.arava@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to redefine enum rt711_jd_src.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 683b0df26c33 ("ASoC: rt711: add two jack detection modes")
added two jack detection modes. Rt711 has 4 JD modes now.
Reserve 4 bits in case rt711 adds more JD modes in the future.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor the machine driver by using the common code in maxim-common
module to support max98360a.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver data for jsl_cs4242_mx98360a which supports two
max98360a speaker amplifiers on SSP1 and cs42l42 headphone codec on
SSP0 running on JSL platform.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move max98360a code to this common module so it could be shared
between multiple SOF machine drivers. MAX98357A and MAX98360A are
sharing same codec driver so here we also share some function and
structures.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there are two types of DAI Link sequences defined in
topology files, one starts from speaker link and the other starts from
headphone link.
Type 1: SPK - HP - DMIC - HDMI
Type 2: HP - DMIC - HDMI - SPK
Here we add a macro SOF_CS42L42_DAILINK to define the DAI Link
sequence in quirk and refactor the sof_card_dai_links_create()
function to support arbitrary DAI Link sequence.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
currenlty wcd938x has only soundwire interface and depends on
symbols from wcd938x soundwire module, so make this dependency
explicit in Kconfig
Without this one of the randconfig endup setting
CONFIG_SND_SOC_WCD938X=y
CONFIG_SND_SOC_WCD938X_SDW=m
resulting in some undefined reference to wcd938x_sdw* symbols.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 045442228868 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210713140417.23693-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADL descriptor was missing an ACPI power setting, causing the DSP
to enter D3 even with a D0i1-compatible wake-on-voice/hotwording
capture stream.
Fixes: 4ad03f894b3c ('ASoC: SOF: Intel: Update ADL P to use its own descriptor')
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712201620.44311-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following fallthrough warning:
sound/soc/mediatek/mt8183/mt8183-dai-adda.c:342:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f1e ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
Changes since v1:
- Do not calculat that we allow one serializer in DIT mode, just set the
max_active_serializers to 1.
Reported-by: kernel test robot <lkp@intel.com>
it has been on my todo list for several years to support McASP on OMAP4 devices.
For Galaxy Nexus we had an omap-mcasp driver (which was mostly a stripped down
davinci-mcasp driver) to support what was needed on that specific phone + it's
dock for S/PDIF (48KHz, 16bit, stereo).
Not many (if any) device available to test the DIT mode of McASP.
I have used BeagleBone White (McASP1 AXR3 can be routed to a pin) to get the
S/PDIF mode working then PandaES for OMAP4 support (on PandaES the gpio_121 is
not used and the signal is routed to expansion J6 pin14).
In theory the McASP in OMAP5 should be working after this series, but the OMAP5
TRM is not public and I do not have one to check the addresses and see if there
is a way to test it on omap5-uevm.
Mark, Tony:
The ASoC and dts patches can go via separate tree I felt that it is better if
they are together, at least initially.
Nikolaus: fyi, this might be useful for Pyra?
Regards,
Péter
---
Peter Ujfalusi (5):
ASoC: ti: davinci-mcasp: Fix DIT mode support
ASoC: dt-bindings: davinci-mcasp: Add compatible string for OMAP4
ASoC: ti: davinci-mcasp: Add support for the OMAP4 version of McASP
ARM: dts: omap4-l4-abe: Correct sidle modes for McASP
ARM: dts: omap4-l4-abe: Add McASP configuration
.../bindings/sound/davinci-mcasp-audio.txt | 1 +
arch/arm/boot/dts/omap4-l4-abe.dtsi | 39 ++--
include/linux/platform_data/davinci_asp.h | 1 +
sound/soc/ti/Kconfig | 1 +
sound/soc/ti/davinci-mcasp.c | 176 +++++++++++++++---
5 files changed, 175 insertions(+), 43 deletions(-)
--
2.32.0
The first fix solves an underflow in SoundWire platforms using the
max98373 amplifier, the rest of the patches are minor corrections in
machine drivers.
The fix should be queued for the 5.14 cycle, the rest should be
harmless but can be deferred for 5.15 if it's too late already.
Brent Lu (2):
ASoC: SOF: add a helper to get topology configured bclk
ASoC: Intel: sof_cs42l42: use helper function to get bclk frequency
Gongjun Song (1):
ASoC: Intel: soc-acpi: add support for SoundWire of TGL-H-RVP
Rander Wang (1):
ASoC: Intel: boards: fix xrun issue on platform with max98373
include/sound/sof.h | 1 +
sound/soc/intel/boards/sof_cs42l42.c | 8 +-
sound/soc/intel/boards/sof_sdw_max98373.c | 81 ++++++++++++-------
.../intel/common/soc-acpi-intel-tgl-match.c | 15 ++++
sound/soc/sof/sof-audio.c | 42 ++++++++--
5 files changed, 111 insertions(+), 36 deletions(-)
--
2.25.1
Thierry Reding <treding@nvidia.com>:
From: Thierry Reding <treding@nvidia.com>
This small series addresses a minor issue with how IOMMU support is
wired up on various Tegra generations. Currently the virtual "card"
device is used to allocate DMA memory for, but since that device does
not actually exist, the path to memory cannot be correctly described.
To address this, this series moves to using the ADMAIF as the DMA device
for audio. This is a real device that can have a proper DMA mask set and
with which a stream ID can be associated with in the SMMU. The memory
accesses technically originate from the ADMA controller (that the ADMAIF
uses), but DMA channel are dynamically allocated at runtime while DMA
memory is allocated at driver load time, drivers won't have access to
the ADMA device yet.
Further patches will be required to correct this issue on Tegra186 and
Tegra210, but I wanted to get feedback on this approach first.
Changes in v2:
- add backwards-compatibility fallback
Thierry
Thierry Reding (2):
ASoC: tegra: Use ADMAIF component for DMA allocations
arm64: tegra: Enable audio IOMMU support on Tegra194
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 4 ++++
sound/soc/tegra/tegra_pcm.c | 30 ++++++++++++++----------
2 files changed, 22 insertions(+), 12 deletions(-)
--
2.32.0
