IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If we have been keeping per-CPU statistics, consider them
regardless of USES_RSS, because we may not actually fill
those, for example in non-fast-RX cases when the connection
is not compatible with fast-RX. If we didn't fill them, the
additional data will be zero and not affect anything, and
if we did fill them then it's more correct to consider them.
This fixes an issue in mesh mode where some statistics are
not updated due to USES_RSS being set, but fast-RX isn't
used.
Reported-by: Thiraviyam Mariyappan <tmariyap@codeaurora.org>
Link: https://lore.kernel.org/r/20210610220814.13b35f5797c5.I511e9b33c5694e0d6cef4b6ae755c873d7c22124@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In 2G band, a HE sta can only supports HT and HE, but not supports VHT.
In this case, default HE tx bitrate mask isn't filled, when we use iw to
set bitrates without any parameter.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210609075944.51130-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use newly introduced helper function ieee80211_is_tx_data to check if
frame is a data frame. Takes into account that hardware encapsulation
can be enabled for a frame and therefore no ieee80211 header is present.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210519122019.92359-4-borgers@mi.fu-berlin.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Data Frames with no ack flag set should be handled by the rate
controler. Make sure we reach the rate controler by returning early
from rate_control_send_low if the frame is a data frame with no ack
flag.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210519122019.92359-3-borgers@mi.fu-berlin.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to differentiate these frames since the ones we
currently put on the skb_queue_tdls_chsw have already
been converted to ethernet format, but now that we've
got a single place to enqueue to the sdata->skb_queue
this isn't hard. Just differentiate based on protocol
and adjust the code to queue the SKBs appropriately.
Link: https://lore.kernel.org/r/20210517230754.17034990abef.I5342f2183c0d246b18d36c511eb3b6be298a6572@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
QoS Data Frames that were sent with a No Ack policy should be ignored by
the minstrel statistics. There will never be an Ack for these frames so
there is no way to draw conclusions about the success of the transmission.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210517120145.132814-1-borgers@mi.fu-berlin.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "ap_info->tbtt_info_len" and "length" variables are the same value
but it is confusing how the names are mixed up. Let's use "length"
everywhere for consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YJaMNzZENkYFAYQX@mwanda
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We no longer need to put any limits here, hardware will and
mac80211-hwsim can do whatever it likes. The reason we had
this was some accounting code (still mentioned in the comment)
but that code was deleted in commit c781944b71f8 ("cfg80211:
Remove unused cfg80211_can_use_iftype_chan()").
Link: https://lore.kernel.org/r/20210506221159.d1d61db1d31c.Iac4da68d54b9f1fdc18a03586bbe06aeb9515425@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Variable 'ret' is set to -ENODEV but this value is never read as it
is overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Clean up the following clang-analyzer warning:
net/mac80211/debugfs_netdev.c:60:2: warning: Value stored to 'ret' is
never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1619774483-116805-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Variable 'ps' is set to wdev->ps but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.
Cleans up the following clang-analyzer warning:
net/wireless/wext-compat.c:1170:7: warning: Value stored to 'ps' during
its initialization is never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1619603945-116891-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following out-of-bounds warning:
net/wireless/wext-spy.c:178:2: warning: 'memcpy' offset [25, 28] from the object at 'threshold' is out of the bounds of referenced subobject 'low' with type 'struct iw_quality' at offset 20 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &threshold.low and &spydata->spy_thr_low. As
these are just a couple of struct members, fix this by using direct
assignments, instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210422200032.GA168995@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current cleanup rbuf tries a bit too hard to avoid acquiring
the subflow socket lock. We may end-up delaying the needed ack,
or skip acking a blocked subflow.
Address the above extending the conditions used to trigger the cleanup
to reflect more closely what TCP does and invoking tcp_cleanup_rbuf()
on all the active subflows.
Note that we can't replicate the exact tests implemented in
tcp_cleanup_rbuf(), as MPTCP lacks some of the required info - e.g.
ping-pong mode.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a new flag named deny_join_id0 in struct
mptcp_options_received. Set it when MP_CAPABLE with the flag
MPTCP_CAP_DENYJOIN_ID0 is received.
Also add a new flag remote_deny_join_id0 in struct mptcp_pm_data. When the
flag deny_join_id0 is set, set this remote_deny_join_id0 flag.
In mptcp_pm_create_subflow_or_signal_addr, if the remote_deny_join_id0 flag
is set, and the remote address id is zero, stop this connection.
Suggested-by: Florian Westphal <fw@strlen.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defined a new flag MPTCP_CAP_DENY_JOIN_ID0 for the third bit,
labeled "C" of the MP_CAPABLE option.
Add a new flag allow_join_id0 in struct mptcp_out_options. If this flag is
set, send out the MP_CAPABLE option with the flag MPTCP_CAP_DENY_JOIN_ID0.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a new sysctl, named allow_join_initial_addr_port, to
control whether allow peers to send join requests to the IP address and
port number used by the initial subflow.
Suggested-by: Florian Westphal <fw@strlen.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, sctp over udp was using udp tunnel's icmp err process, which
only does sk lookup on sctp side. However for sctp's icmp error process,
there are more things to do, like syncing assoc pmtu/retransmit packets
for toobig type err, and starting proto_unreach_timer for unreach type
err etc.
Now after adding PLPMTUD, which also requires to process toobig type err
on sctp side. This patch is to process icmp err on sctp side by parsing
the type/code/info in .encap_err_lookup and call sctp's icmp processing
functions. Note as the 'redirect' err process needs to know the outer
ip(v6) header's, we have to leave it to udp(v6)_err to handle it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extract sctp_v4_err_handle() from sctp_v4_err() to
only handle the icmp err after the sock lookup, and it also makes
the code clearer.
sctp_v4_err_handle() will be used in sctp over udp's err handling
in the following patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extract sctp_v6_err_handle() from sctp_v6_err() to
only handle the icmp err after the sock lookup, and it also makes
the code clearer.
sctp_v6_err_handle() will be used in sctp over udp's err handling
in the following patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as in tcp_v6_err() and __udp6_lib_err(), there's no need to
hold idev in sctp_v6_err(), so just call __in6_dev_get() instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_transport_pl_reset() is called whenever any of these 3 members in
transport is changed:
- probe_interval
- param_flags & SPP_PMTUD_ENABLE
- state == ACTIVE
If all are true, start the PLPMTUD when it's not yet started. If any of
these is false, stop the PLPMTUD when it's already running.
sctp_transport_pl_update() is called when the transport dst has changed.
It will restart the PLPMTUD probe. Again, the pathmtu won't change but
use the dst's mtu until the Search phase is done.
Note that after using PLPMTUD, the pathmtu is only initialized with the
dst mtu when the transport dst changes. At other time it is updated by
pl.pmtu. So sctp_transport_pmtu_check() will be called only when PLPMTUD
is disabled in sctp_packet_config().
After this patch, the PLPMTUD feature from RFC8899 will be activated
and can be used by users.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLPMTUD will short-circuit the old process for icmp TOOBIG packets.
This part is described in rfc8899#section-4.6.2 (PL_PTB_SIZE =
PTB_SIZE - other_headers_len). Note that from rfc8899#section-5.2
State Machine, each case below is for some specific states only:
a) PL_PTB_SIZE < MIN_PLPMTU || PL_PTB_SIZE >= PROBED_SIZE,
discard it, for any state
b) MIN_PLPMTU < PL_PTB_SIZE < BASE_PLPMTU,
Base -> Error, for Base state
c) BASE_PLPMTU <= PL_PTB_SIZE < PLPMTU,
Search -> Base or Complete -> Base, for Search and Complete states.
d) PLPMTU < PL_PTB_SIZE < PROBED_SIZE,
set pl.probe_size to PL_PTB_SIZE then verify it, for Search state.
The most important one is case d), which will help find the optimal
fast during searching. Like when pathmtu = 1392 for SCTP over IPv4,
the search will be (20 is iphdr_len):
1. probe with 1200 - 20
2. probe with 1232 - 20
3. probe with 1264 - 20
...
7. probe with 1388 - 20
8. probe with 1420 - 20
When sending the probe with 1420 - 20, TOOBIG may come with PL_PTB_SIZE =
1392 - 20. Then it matches case d), and saves some rounds to try with the
1392 - 20 probe. But of course, PLPMTUD doesn't trust TOOBIG packets, and
it will go back to the common searching once the probe with the new size
can't be verified.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As described in rfc8899#section-5.2, when a probe succeeds, there might
be the following state transitions:
- Base -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_BIG_STEP,
- Error -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is changed from SCTP_MIN_PLPMTU to SCTP_BASE_PLPMTU,
pl.probe_size increases by SCTP_PL_BIG_STEP.
- Search -> Search Complete, occurs when probe succeeds with the probe
size SCTP_MAX_PLPMTU less than pl.probe_high,
pl.pmtu is not changing, but update *pathmtu* with it,
pl.probe_size is set back to pl.pmtu to double check it.
- Search Complete -> Search, occurs when probe succeeds with the probe
size equal to pl.pmtu,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_MIN_STEP.
So search process can be described as:
1. When it just enters 'Search' state, *pathmtu* is not updated with
pl.pmtu, and probe_size increases by a big step (SCTP_PL_BIG_STEP)
each round.
2. Until pl.probe_high is set when a probe fails, and probe_size
decreases back to pl.pmtu, as described in the last patch.
3. When the probe with the new size succeeds, probe_size changes to
increase by a small step (SCTP_PL_MIN_STEP) due to pl.probe_high
is set.
4. Until probe_size is next to pl.probe_high, the searching finishes and
it goes to 'Complete' state and updates *pathmtu* with pl.pmtu, and
then probe_size is set to pl.pmtu to confirm by once more probe.
5. This probe occurs after "30 * probe_inteval", a much longer time than
that in Search state. Once it is done it goes to 'Search' state again
with probe_size increased by SCTP_PL_MIN_STEP.
As we can see above, during the searching, pl.pmtu changes while *pathmtu*
doesn't. *pathmtu* is only updated when the search finishes by which it
gets an optimal value for it. A big step is used at the beginning until
it gets close to the optimal value, then it changes to a small step until
it has this optimal value.
The small step is also used in 'Complete' until it goes to 'Search' state
again and the probe with 'pmtu + the small step' succeeds, which means a
higher size could be used. Then probe_size changes to increase by a big
step again until it gets close to the next optimal value.
Note that anytime when black hole is detected, it goes directly to 'Base'
state with pl.pmtu set to SCTP_BASE_PLPMTU, as described in the last patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state transition is described in rfc8899#section-5.2,
PROBE_COUNT == MAX_PROBES means the probe fails for MAX times, and the
state transition includes:
- Base -> Error, occurs when BASE_PLPMTU Confirmation Fails,
pl.pmtu is set to SCTP_MIN_PLPMTU,
probe_size is still SCTP_BASE_PLPMTU;
- Search -> Base, occurs when Black Hole Detected,
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
- Search Complete -> Base, occurs when Black Hole Detected
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
Note a black hole is encountered when a sender is unaware that packets
are not being delivered to the destination endpoint. So it includes the
probe failures with equal probe_size to pl.pmtu, and definitely not
include that with greater probe_size than pl.pmtu. The later one is the
normal probe failure where probe_size should decrease back to pl.pmtu
and pl.probe_high is set. pl.probe_high would be used on HB ACK recv
path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does exactly what rfc8899#section-6.2.1.2 says:
The SCTP sender needs to be able to determine the total size of a
probe packet. The HEARTBEAT chunk could carry a Heartbeat
Information parameter that includes, besides the information
suggested in [RFC4960], the probe size to help an implementation
associate a HEARTBEAT ACK with the size of probe that was sent. The
sender could also use other methods, such as sending a nonce and
verifying the information returned also contains the corresponding
nonce. The length of the PAD chunk is computed by reducing the
probing size by the size of the SCTP common header and the HEARTBEAT
chunk.
Note that HB ACK chunk will carry back whatever HB chunk carried, including
the probe_size we put it in; We also check hbinfo->probe_size in the HB ACK
against link->pl.probe_size to validate this HB ACK chunk.
v1->v2:
- Remove the unused 'sp' and add static for sctp_packet_bundle_pad().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 timers described in rfc8899#section-5.1.1:
PROBE_TIMER, PMTU_RAISE_TIMER, CONFIRMATION_TIMER
This patches adds a 'probe_timer' in transport, and it works as either
PROBE_TIMER or PMTU_RAISE_TIMER. At most time, it works as PROBE_TIMER
and expires every a 'probe_interval' time to send the HB probe packet.
When transport pl enters COMPLETE state, it works as PMTU_RAISE_TIMER
and expires in 'probe_interval * 30' time to go back to SEARCH state
and do searching again.
SCTP HB is an acknowledged packet, CONFIRMATION_TIMER is not needed.
The timer will start when transport pl enters BASE state and stop
when it enters DISABLED state.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this socket option, users can change probe_interval for
a transport, asoc or sock after it's created.
Note that if the change is for an asoc, also apply the change
to each transport in this asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLPMTUD can be enabled by doing 'sysctl -w net.sctp.probe_interval=n'.
'n' is the interval for PLPMTUD probe timer in milliseconds, and it
can't be less than 5000 if it's not 0.
All asoc/transport's PLPMTUD in a new socket will be enabled by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chunk is defined in rfc4820#section-3, and used to pad an
SCTP packet. The receiver must discard this chunk and continue
processing the rest of the chunks in the packet.
Add it now, as it will be bundled with a heartbeat chunk to probe
pmtu in the following patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes openvswitch module use the event tracing framework
to log the upcall interface and action execution pipeline. When
using openvswitch as the packet forwarding engine, some types of
debugging are made possible simply by using the ovs-vswitchd's
ofproto/trace command. However, such a command has some
limitations:
1. When trying to trace packets that go through the CT action,
the state of the packet can't be determined, and probably
would be potentially wrong.
2. Deducing problem packets can sometimes be difficult as well
even if many of the flows are known
3. It's possible to use the openvswitch module even without
the ovs-vswitchd (although, not common use).
Introduce the event tracing points here to make it possible for
working through these problems in kernel space. The style is
copied from the mac80211 driver-trace / trace code for
consistency - this creates some checkpatch splats, but the
official 'guide' for adding tracepoints, as well as the existing
examples all add the same splats so it seems acceptable.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the offset to read from module EEPROM as part of the netlink
policy and remove the corresponding check from the code.
This also makes it possible to query the offset range from user space:
$ genl ctrl policy name ethtool
...
ID: 0x14 policy[32]:attr[2]: type=U32 range:[0,255]
...
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate the number of bytes to read from the module EEPROM as part of
the netlink policy and remove the corresponding check from the code.
This also makes it possible to query the length range from user space:
$ genl ctrl policy name ethtool
...
ID: 0x14 policy[32]:attr[3]: type=U32 range:[1,128]
...
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ETHTOOL_A_MODULE_EEPROM_DATA' attribute is not part of the get
request.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements are not needed in Void function.
Signed-off-by: gushengxian <gushengxian@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account this exceptional events for better introspection.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we check the msk state to avoid enqueuing new
skbs at msk shutdown time.
Such test is racy - as we can't acquire the msk socket lock -
and useless, as the caller already checked the subflow
field 'disposable', covering the same scenario in a race
free manner - read and updated under the ssk socket lock.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't flush entirely the receive queue, we need set
again such bit later. We can simply avoid clearing it.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a bunch of callsite where the ssk socket
lock is acquired using the full-blown version eligible for
the fast variant. Let's move to the latter.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned cache was introduced to reduce the number of skb
allocation in atomic context, but the required complexity is
excessive.
This change remove the mentioned cache.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0dca2c7404a938cb10c85d0515cee40ed5348788.
The commit in question breaks hardware offload of flower filters.
Quoting Vladimir Oltean <olteanv@gmail.com>:
fl_hw_replace_filter() and fl_reoffload() create a struct
flow_cls_offload with a rule->match.mask member derived from the mask
of the software classifier: &f->mask->key - that same mask that is used
for initializing the flow dissector keys, and the one from which Boris
removed the basic.n_proto member because it was bothering him.
Reported-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the pr_info content from int to char * in sock_register() and
sock_unregister(), this looks more readable.
Fixed build error in ARCH=sparc64.
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MRP hardware assist being supported only by the ocelot switch
family, which by design does not support cross-chip bridging, the
current match functions are at best a guess and have not been confirmed
in any way to do anything relevant in a multi-switch topology.
Drop the code and make the notifiers match only on the targeted switch
port.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_change_mtu() calls dsa_port_mtu_change() twice:
- it sends a cross-chip notifier with the MTU of the CPU port which is
used to update the DSA links.
- it sends one targeted MTU notifier which is supposed to only match the
user port on which we are changing the MTU. The "propagate_upstream"
variable is used here to bypass the cross-chip notifier system from
switch.c
But due to a mistake, the second, targeted notifier matches not only on
the user port, but also on the DSA link which is a member of the same
switch, if that exists.
And because the DSA links of the entire dst were programmed in a
previous round to the largest_mtu via a "propagate_upstream == true"
notification, then the dsa_port_mtu_change(propagate_upstream == false)
call that is immediately upcoming will break the MTU on the one DSA link
which is chip-wise local to the dp whose MTU is changing right now.
Example given this daisy chain topology:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
ip link set sw0p1 mtu 9000
ip link set sw1p1 mtu 9000 # at this stage, sw0p1 and sw1p1 can talk
# to one another using jumbo frames
ip link set sw0p2 mtu 1500 # this programs the sw0p3 DSA link first to
# the largest_mtu of 9000, then reprograms it to
# 1500 with the "propagate_upstream == false"
# notifier, breaking communication between
# sw0p1 and sw1p1
To escape from this situation, make the targeted match really match on a
single port - the user port, and rename the "propagate_upstream"
variable to "targeted_match" to clarify the intention and avoid future
issues.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a cross-chip topology like this:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ cpu ] [ user ] [ user ] [ dsa ] [ user ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
and we issue the following commands:
1. ip link set sw0p1 mtu 1700
2. ip link set sw1p1 mtu 1600
we notice the following happening:
Command 1. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 0, of 1700. This matches
sw0p0, sw0p3 and sw1p4 (all CPU ports and DSA links).
Then, it emits a targeted MTU notifier for the user port (sw0p1), again
with MTU 1700 (this doesn't matter).
Command 2. emits a non-targeted MTU notifier for the CPU port (sw0p0)
with the largest_mtu calculated across switch 1, of 1600. This matches
the same group of ports as above, and decreases the MTU for the CPU port
and the DSA links from 1700 to 1600.
As a result, the sw0p1 user port can no longer communicate with its CPU
port at MTU 1700.
To address this, we should calculate the largest_mtu across all switches
that may share a CPU port, and only emit MTU notifiers with that value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the notifier for adding a multicast MAC address matches on
the targeted port and on all DSA links in the system, be they upstream
or downstream links.
This leads to a considerable amount of useless traffic.
Consider this daisy chain topology, and a MDB add notifier emitted on
sw0p0. It matches on sw0p0, sw0p3, sw1p3 and sw2p4.
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ x ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ x ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
But switch 0 has no reason to send the multicast traffic for that MAC
address on sw0p3, which is how it reaches switches 1 and 2. Those
switches don't expect, according to the user configuration, to receive
this multicast address from switch 1, and they will drop it anyway,
because the only valid destination is the port they received it on.
They only need to configure themselves to deliver that multicast address
_towards_ switch 1, where the MDB entry is installed.
Similarly, switch 1 should not send this multicast traffic towards
sw1p3, because that is how it reaches switch 2.
With this change, the heat map for this MDB notifier changes as follows:
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
[ x ] [ ] [ ] [ ] [ ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
[ ] [ ] [ ] [ ] [ x ]
Now the mdb notifier behaves the same as the fdb notifier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
