IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Commit ae15e0ba1b33 ("ice: Change number of XDP Tx queues to match
number of Rx queues") tried to address the incorrect setting of XDP
queue count that was based on the Tx queue count, whereas in theory we
should provide the XDP queue per Rx queue. However, the routines that
setup and destroy the set of Tx resources are still based on the
vsi->num_txq.
Ice supports the asynchronous Tx/Rx queue count, so for a setup where
vsi->num_txq > vsi->num_rxq, ice_vsi_stop_tx_rings and ice_vsi_cfg_txqs
will be accessing the vsi->xdp_rings out of the bounds.
Parameterize two mentioned functions so they get the size of Tx resources
array as the input.
Fixes: ae15e0ba1b33 ("ice: Change number of XDP Tx queues to match number of Rx queues")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b6047 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.
SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.
Then ethernet header has to have to correct value for
the protocol though.
Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).
Fixes: 0c3a6101ff2d ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ethtool incorrectly reported supported and advertised auto-negotiation
settings for a backplane PHY image which did not support auto-negotiation.
This can occur when using media or PHY type for reporting ethtool
supported and advertised auto-negotiation settings.
Remove setting supported and advertised auto-negotiation settings based
on PHY type in ice_phy_type_to_ethtool(), and MAC type in
ice_get_link_ksettings().
Ethtool supported and advertised auto-negotiation settings should be
based on the PHY image using the AQ command get PHY capabilities with
media. Add setting supported and advertised auto-negotiation settings
based get PHY capabilities with media in ice_get_link_ksettings().
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VSI rebuild can be failed for LAN queue config, then the VF's VSI will
be NULL, the VF reset should be stopped with the VF entering into the
disable state.
Fixes: 12bb018c538c ("ice: Refactor VF reset")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282cf8 ("ice: clear VF ARQLEN register on reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12bb018c538c ("ice: Refactor VF reset") caused a regression
that removes the ability for a VF to request a different amount of
queues via VIRTCHNL_OP_REQUEST_QUEUES. This prevents VF drivers to
either increase or decrease the number of queue pairs they are
allocated. Fix this by using the variable vf->num_req_qs when
determining the vf->num_vf_qs during VF VSI creation.
Fixes: 12bb018c538c ("ice: Refactor VF reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c7a219048e45 ("ice: Remove xsk_buff_pool from VSI structure")
silently introduced a regression and broke the Tx side of AF_XDP in copy
mode. xsk_pool on ice_ring is set only based on the existence of the XDP
prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed.
That is not something that should happen for copy mode as it should use
the regular data path ice_clean_tx_irq.
This results in a following splat when xdpsock is run in txonly or l2fwd
scenarios in copy mode:
<snip>
[ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 106.057269] #PF: supervisor read access in kernel mode
[ 106.062493] #PF: error_code(0x0000) - not-present page
[ 106.067709] PGD 0 P4D 0
[ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45
[ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50
[ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00
[ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206
[ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800
[ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800
[ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800
[ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff
[ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018
[ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000
[ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0
[ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.192898] PKRU: 55555554
[ 106.195653] Call Trace:
[ 106.198143] <IRQ>
[ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice]
[ 106.205087] ice_napi_poll+0x3e/0x590 [ice]
[ 106.209356] __napi_poll+0x2a/0x160
[ 106.212911] net_rx_action+0xd6/0x200
[ 106.216634] __do_softirq+0xbf/0x29b
[ 106.220274] irq_exit_rcu+0x88/0xc0
[ 106.223819] common_interrupt+0x7b/0xa0
[ 106.227719] </IRQ>
[ 106.229857] asm_common_interrupt+0x1e/0x40
</snip>
Fix this by introducing the bitmap of queues that are zero-copy enabled,
where each bit, corresponding to a queue id that xsk pool is being
configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and
checked within ice_xsk_pool(). The latter is a function used for
deciding which napi poll routine is executed.
Idea is being taken from our other drivers such as i40e and ixgbe.
Fixes: c7a219048e45 ("ice: Remove xsk_buff_pool from VSI structure")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864d9 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc1e ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327c0 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Beyond a specific version of firmware, there is no need to provide
override values to the firmware when setting PHY capabilities. In this
case, we do not need to indicate whether we're in Strict or Lenient Link
Mode.
In the case of translating capabilities to the configuration structure,
the module compliance enforcement is already correctly set by firmware,
so the extra code block is redundant.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, use assignment instead of memset/memcpy
where possible
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return more appropriate error codes so that the right error
message is communicated to the user by ethtool.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, change 'abilities' to 'phy_caps' and 'p' to
'pi'. This is more consistent with similar usages elsewhere in the
driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The loop checking for PF VSI doesn't make any sense. The VSI type
backing the netdev passed to ice_set_link_ksettings will always be
of type ICE_PF_VSI. Remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the recursive way of adding the nodes to the layer in order
to reduce the stack usage. Instead the algorithm is modified to use
a while loop.
The previous code was scanning recursively the nodes horizontally.
The total stack consumption will be based on number of nodes present
on that layer. In some cases it can consume more stack.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Retry sending some AQ commands, as result of EBUSY AQ error.
ice_aqc_opc_get_link_topo
ice_aqc_opc_lldp_stop
ice_aqc_opc_lldp_start
ice_aqc_opc_lldp_filter_ctrl
This change follows the latest guidelines from HW team. It is
better to retry the same AQ command several times, as the result
of EBUSY, instead of returning error to the caller right away.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
