IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
NXP Layerscape (ls1028a, ls2088a), dra7xxx and imx6 platforms are either
programmed or statically configured to forward the error triggered by a
link-down state (eg no connected endpoint device) on the system bus for
PCI configuration transactions; these errors are reported as an SError
at system level, which is fatal.
Enumerating a PCI tree when the PCIe link is down is not sensible
either, so even if the link-up check is racy (link can go down after
map_bus() is called) add a link-up check in map_bus() to prevent issuing
configuration transactions when the link is down.
SError report:
SError Interrupt on CPU2, code 0xbf000002 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : pci_generic_config_read+0x3c/0xe0
lr : pci_generic_config_read+0x24/0xe0
sp : ffff80001003b7b0
x29: ffff80001003b7b0 x28: ffff80001003ba74
x27: ffff000971d96800 x26: ffff00096e77e0a8
x25: ffff80001003b874 x24: ffff80001003b924
x23: 0000000000000004 x22: 0000000000000000
x21: 0000000000000000 x20: ffff80001003b874
x19: 0000000000000004 x18: ffffffffffffffff
x17: 00000000000000c0 x16: fffffe0025981840
x15: ffffb94c75b69948 x14: 62203a383634203a
x13: 666e6f635f726568 x12: 202c31203d207265
x11: 626d756e3e2d7375 x10: 656877202c307830
x9 : 203d206e66766564 x8 : 0000000000000908
x7 : 0000000000000908 x6 : ffff800010900000
x5 : ffff00096e77e080 x4 : 0000000000000000
x3 : 0000000000000003 x2 : 84fa3440ff7e7000
x1 : 0000000000000000 x0 : ffff800010034000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x18/0x28
dump_stack+0xd8/0x134
panic+0x180/0x398
add_taint+0x0/0xb0
arm64_serror_panic+0x78/0x88
do_serror+0x68/0x180
el1_error+0x84/0x100
pci_generic_config_read+0x3c/0xe0
dw_pcie_rd_other_conf+0x78/0x110
pci_bus_read_config_dword+0x88/0xe8
pci_bus_generic_read_dev_vendor_id+0x30/0x1b0
pci_bus_read_dev_vendor_id+0x4c/0x78
pci_scan_single_device+0x80/0x100
Link: https://lore.kernel.org/r/20200916054130.8685-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log, remove Fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009155505.5a580ef5@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/20201009155436.27e67238@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-5-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
devices which require non-PCI based MSI handling.
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which allows
to utilize the full functionality of hierarchical irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the irqdomain
which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch and
let the last few users select it.
-----BEGIN PGP SIGNATURE-----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=JlqV
-----END PGP SIGNATURE-----
Merge tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
Fix sparse build warning:
drivers/pci/controller/pcie-iproc-platform.c:102:33: warning: Using plain integer as NULL pointer
The map_irq member of the struct iproc_pcie takes a function pointer
serving as a callback to map interrupts, therefore we should pass a NULL
pointer to it rather than a integer in the iproc_pcie_pltfm_probe()
function.
Related:
commit b64aa11eb2dd ("PCI: Set bridge map_irq and swizzle_irq to
default functions")
Link: https://lore.kernel.org/r/20200922194932.465925-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/20200918181251.32423-1-khilman@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yue Wang <yue.wang@amlogic.com>
Old ATF automatically power on pcie phy and does not provide SMC call for
phy power on functionality which leads to aardvark initialization failure:
[ 0.330134] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 0.338846] phy phy-d0018300.phy.1: phy poweron failed --> -95
[ 0.344753] advk-pcie d0070000.pcie: Failed to initialize PHY (-95)
[ 0.351160] advk-pcie: probe of d0070000.pcie failed with error -95
This patch fixes above failure by ignoring 'not supported' error in
aardvark driver. In this case it is expected that phy is already power on.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-3-pali@kernel.org
Fixes: 366697018c9a ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org> # 5.8+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
The value assigned to msi_val after the inner loop finishes its run is
never used for anything, and it is also immediately overridden in the
line that follows with the return value from the xgene_msi_int_read()
function.
Since the value of msi_val following the inner loop completion is never
used in any meaningful way the assignment can be removed.
Addresses-Coverity-ID: 1437183 ("Unused value")
Link: https://lore.kernel.org/r/20200922030257.459898-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify the return expression by removing useless code.
Link: https://lore.kernel.org/r/20200921082447.2591877-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
module_bcma_driver() makes the code simpler by eliminating
boilerplate code.
Link: https://lore.kernel.org/r/20200918030829.3946025-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.
Link: https://lore.kernel.org/r/20200911175232.19016-11-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The
2711 family requires 128B whereas other devices can employ 512. The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;
Value Type_Generic Type_7278
00 Reserved 128B
01 128B 256B
10 256B 512B
11 512B Reserved
Link: https://lore.kernel.org/r/20200911175232.19016-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts. In
addition, the interrupts lie in bits [31..24] for these legacy chips. This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.
Link: https://lore.kernel.org/r/20200911175232.19016-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The Raspberry Pi (RPI) is currently the only chip using this driver
(pcie-brcmstb.c). There, only one memory controller is used, without an
extension region, and the SCB0 viewport size is set to the size of the
first and only dma-range region. Other BrcmSTB SOCs have more complicated
memory configurations that require setting additional viewport sizes.
BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC. The SOC may have one to three memory
controllers; they are indicated by the term SCBi. Each controller has a
base region and an optional extension region. In physical memory, the base
and extension regions of a controller are not adjacent, but in PCIe-space
they are.
There is a "viewport" for each memory controller that allows DMA from
endpoint devices. Each viewport's size must be set to a power of two, and
that size must be equal to or larger than the amount of memory each
controller supports which is the sum of base region and its optional
extension. Further, the 1-3 viewports are also adjacent in PCIe-space.
Unfortunately the viewport sizes cannot be ascertained from the
"dma-ranges" property so they have their own property, "brcm,scb-sizes".
This is because dma-range information does not indicate what memory
controller it is associated. For example, consider the following case
where the size of one dma-range is 2GB and the second dma-range is 1GB:
/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
By just looking at the dma-ranges information, one cannot tell which
situation applies. That is why an additional property is needed. Its
length indicates the number of memory controllers being used and each value
indicates the viewport size.
Note that the RPI DT does not have a "brcm,scb-sizes" property value,
as it is assumed that it only requires one memory controller and no
extension. So the optional use of "brcm,scb-sizes" will be backwards
compatible.
One last layer of complexity exists: all of the viewports sizes must be
added and rounded up to a power of two to determine what the "BAR" size is.
Further, an offset must be given that indicates the base PCIe address of
this "BAR". The use of the term BAR is typically associated with endpoint
devices, and the term is used here because the PCIe HW may be used as an RC
or an EP. In the former case, all of the system memory appears in a single
"BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely
used in the EP role and its system of mapping memory is an artifact that
requires multiple dma-ranges regions.
Link: https://lore.kernel.org/r/20200911175232.19016-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/20200911175232.19016-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_restore_msi_state() directly writes the MSI/MSI-X related registers
via MMIO. On a physical machine, this works perfectly; for a Linux VM
running on a hypervisor, which typically enables IOMMU interrupt remapping,
the hypervisor usually should trap and emulate the MMIO accesses in order
to re-create the necessary interrupt remapping table entries in the IOMMU,
otherwise the interrupts can not work in the VM after hibernation.
Hyper-V is different from other hypervisors in that it does not trap and
emulate the MMIO accesses, and instead it uses a para-virtualized method,
which requires the VM to call hv_compose_msi_msg() to notify the hypervisor
of the info that would be passed to the hypervisor in the case of the
trap-and-emulate method. This is not an issue to a lot of PCI device
drivers, which destroy and re-create the interrupts across hibernation, so
hv_compose_msi_msg() is called automatically. However, some PCI device
drivers (e.g. the in-tree GPU driver nouveau and the out-of-tree Nvidia
proprietary GPU driver) do not destroy and re-create MSI/MSI-X interrupts
across hibernation, so hv_pci_resume() has to call hv_compose_msi_msg(),
otherwise the PCI device drivers can no longer receive interrupts after
the VM resumes from hibernation.
Hyper-V is also different in that chip->irq_unmask() may fail in a
Linux VM running on Hyper-V (on a physical machine, chip->irq_unmask()
can not fail because unmasking an MSI/MSI-X register just means an MMIO
write): during hibernation, when a CPU is offlined, the kernel tries
to move the interrupt to the remaining CPUs that haven't been offlined
yet. In this case, hv_irq_unmask() -> hv_do_hypercall() always fails
because the vmbus channel has been closed: here the early "return" in
hv_irq_unmask() means the pci_msi_unmask_irq() is not called, i.e. the
desc->masked remains "true", so later after hibernation, the MSI interrupt
always remains masked, which is incorrect. Refer to cpu_disable_common()
-> fixup_irqs() -> irq_migrate_all_off_this_cpu() -> migrate_one_irq():
static bool migrate_one_irq(struct irq_desc *desc)
{
...
if (maskchip && chip->irq_mask)
chip->irq_mask(d);
...
err = irq_do_set_affinity(d, affinity, false);
...
if (maskchip && chip->irq_unmask)
chip->irq_unmask(d);
Fix the issue by calling pci_msi_unmask_irq() unconditionally in
hv_irq_unmask(). Also suppress the error message for hibernation because
the hypercall failure during hibernation does not matter (at this time
all the devices have been frozen). Note: the correct affinity info is
still updated into the irqdata data structure in migrate_one_irq() ->
irq_do_set_affinity() -> hv_set_affinity(), so later when the VM
resumes, hv_pci_restore_msi_state() is able to correctly restore
the interrupt with the correct affinity.
Link: https://lore.kernel.org/r/20201002085158.9168-1-decui@microsoft.com
Fixes: ac82fc832708 ("PCI: hv: Add hibernation support")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Link: https://lore.kernel.org/r/20200916025025.3992783-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add missing documentation for the parameter "version" and "num_version"
of the hv_pci_protocol_negotiation() function and resolve build time
kernel-doc warnings:
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'version' not described in 'hv_pci_protocol_negotiation'
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'num_version' not described in 'hv_pci_protocol_negotiation'
No change to functionality intended.
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20200925234753.1767227-1-kw@linux.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The arch_.*_msi_irq[s] fallbacks are compiled in whether an architecture
requires them or not. Architectures which are fully utilizing hierarchical
irq domains should never call into that code.
It's not only architectures which depend on that by implementing one or
more of the weak functions, there is also a bunch of drivers which relies
on the weak functions which invoke msi_controller::setup_irq[s] and
msi_controller::teardown_irq.
Make the architectures and drivers which rely on them select them in Kconfig
and if not selected replace them by stub functions which emit a warning and
fail the PCI/MSI interrupt allocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112333.992429909@linutronix.de
Devices on the VMD bus use their own MSI irq domain, but it is not
distinguishable from regular PCI/MSI irq domains. This is required
to exclude VMD devices from getting the irq domain pointer set by
interrupt remapping.
Override the default bus token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.047315047@linutronix.de
pci_msi_get_hwirq() and pci_msi_set_desc are not longer special. Enable the
generic MSI domain ops in the core and PCI MSI code unconditionally and get
rid of the x86 specific implementations in the X86 MSI code and in the
hyperv PCI driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200826112332.564274859@linutronix.de
Convert the interrupt remap drivers to retrieve the pci device from the msi
descriptor and use info::hwirq.
This is the first step to prepare x86 for using the generic MSI domain ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.466405395@linutronix.de
VMD has it's own PCI/MSI interrupt domain which is not in any way depending
on the x86 vector domain. PCI devices behind VMD share the VMD MSIX vector
entries via a VMD specific message translation to the actual VMD MSIX
vector. The VMD device interrupt handler for the VMD MSIX vectors invokes
all interrupt handlers of the devices which share a vector.
Making the x86 vector domain the actual parent of the VMD irq domain is
pointless and actually counterproductive. When a device interrupt is
requested then it will activate the interrupt which traverses down the
hierarchy and consumes an interrupt vector in the vector domain which is
never used.
The domain is self contained and has no parent dependencies, so just hand
in NULL for the parent and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112330.928952181@linutronix.de
The HiSilicon HIP PCIe controller is capable of handling errors
on root port and performing port reset separately at each root port.
Add error handling driver for HIP PCIe controller to log
and report recoverable errors. Perform root port reset and restore
link status after the recovery.
Following are some of the PCIe controller's recoverable errors
1. completion transmission timeout error.
2. CRS retry counter over the threshold error.
3. ECC 2 bit errors
4. AXI bresponse/rresponse errors etc.
The driver placed in the drivers/pci/controller/ because the
HIP PCIe controller does not use DWC IP.
Link: https://lore.kernel.org/r/20200903123456.1823-3-shiju.jose@huawei.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
'max_width' is read, but never used, so let's remove it.
Link: https://lore.kernel.org/r/20200821035420.380495-39-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The PCI_CAP_ID_EXP offset is only needed by intel_pcie_link_setup(), so
let's retrieve it there and avoid storing the offset.
Link: https://lore.kernel.org/r/20200821035420.380495-38-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
