IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.
In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In TX vring allocation, vring_tx->va is allocated before WMI command to
configure the vring is sent to the device. As the WMI command can take
time to complete, it can lead to scenarios where vring_tx->va is not NULL
but vring is still not enabled.
This patch adds a check that vring_tx_data is enabled before returning
a valid TX vring.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil_vring_fini_tx is called in disconnect in order to free the
allocated vrings.
wil_vring_fini_tx is disabling the vring_tx_data before napi_synchronize
is called in order to avoid the tx handling of this vring, while
wil_vring_free is called only after napi finished the current handling
of the tx completed packets.
Due to that, in case of disconnect, wil6210_netdev_poll_tx can be called
when vring->va is not NULL but vring_tx_data[i]->enabled is already
disabled.
This patch checks vring_tx_data[i]->enabled in wil6210_netdev_poll_tx
to prevent handling of disabled vrings.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the start_ap/change_beacon API, when we set up probe response
offloading, we only use the IE list from the probe response
template and not the IE list from the proberesp_ies argument.
As a result, we miss important IEs and it causes problems with
some scenarios such as P2P.
With this change, we merge the list of IEs from the probe response
template and proberesp_ies and send the merged list to the FW
for offloading. It is still FW responsibility to filter out
irrelevant IEs when sending probe response, based on the actual
contents of the probe request.
Also in case association response termplate is not provided,
we will use the merged list of IEs from probe response in the
association response as well.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the privacy flag calculation in change_beacon
checks for RSN IE inside proberesp_ies, but normally it
is not found there. It works today because of code inside
the function wil_fix_bcon, but wil_fix_bcon is not directly
related to change_beacon, and it may be changed or removed
in the future and break the calculation.
To fix this issue, change the privacy flag calculation
to check RSN IE inside the beacon itself. The new check is more
reliable and will not be sensitive to changes in wil_fix_bcon.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This device is available under different marketing names:
WLM-20U2 - Wireless USB Dongle for Toshiba TVs
GN-1080 - Wireless LAN Module for Toshiba MFPs.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Request NOA update when chanctx active, also in case
of STA.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The p2p NOA never been supported at 10.2.4 FW, remove it to avoid SWBA
event parse error for multi beacon interval case.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Register for 500ms as periodic peer stats update period,
and parameters like rx_duration that needs to be tracked
in host can be achieved by this provision, also periodic
stats update is the future of fw_stats and shall be extended
for pdev / vdev stats irrespecitive PEER_STATS service is enabled
or not
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: fix a checkpatch warning]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for periodic peer stats update when peer stats
service is enabled. The host to update the peer stats received
from the firmware periodically, since firmware will reset this to zero
after sometime (due to memory constraints)
While enabling periodic peer / vdev stats cleanup the existing
list in debugfs if max limit is reached, so that the new stats is
updated.
Ideally speaking based on 'Michal Kazior's' suggestion
we need to completely move to periodic update of all the stats making
the 'ping - pong' method obselete. This requires a bit of re-work and
some testing as well, also confirmation regarding backward comptability
for various firmware and chipsets. Hence allow periodic update only
for peer_stats.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prerequisite patch to address checkpatch errors for the next patch
in this series, this function names are bit too long, make it short
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace the local variable 'burst_enable' with 'param'
for mapping and setting pdev paraemeters and with this patch
pretty easy to extend support for new parameters adhering to
linux kernel coding guidelines
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix naming of peer stats rssi_changed field in 10.2.4 to make it
more readable. As of now this field is not used, but necessary to
pull in fw_stats with appropriate length.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for parsing 'peer_rx_duration' as part
of 10.2.4 peer_stats. Also register PEER_STATS service
for parsing 'rx_duration' (and for any new fields to be added
as part of peer_stats). Have checks for backward compatibility with
older 10.2.4 firmware incase PEER_STATS service is not enabled
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On multicore systems it was possible for the txrx
tasklet to keep on running for long periods of
time on a single CPU due to tx completion
processing. Another CPU could feed the running
tasklet for an indefinite amount of time.
The tasklet is now guaranteed to run a finite
amount of time and is limited by HTT CE Rx ring
depth.
This improves behavior when RPS is used on target
system and might improve TCP handling as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per comments from Bjorn Andersson <bjorn.andersson@sonymobile.com>,
split DMA mask register writing as seperate patch in case we need
bi-sect in the furture.
Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Lawrence reported that git clone could make system crash on a
Qualcomm ARM soc based device (DragonBoard, 1G memory without
swap) running 64bit Debian.
It's turned out the crash is related with rx skb allocation
failure. git could consume more than 600MB anonymous memory.
And system is in extremely memory shortage case.
But driver didn't handle the rx allocation failure case. This patch
doesn't submit skb to upper layer if rx skb allocation fails.
Instead, it reuse the old skb for rx DMA again. It's more like
drop the packets if system is in memory shortage case.
With this change, git clone is OOMed instead of system crash.
Reported-by: King, Lawrence <lking@qti.qualcomm.com>
Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a type bug so it always returns success.
Fixes: 6fa658fd5ab2 ('ath9k: Simplify and fix eeprom endianness swapping')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath9k driver does not modify tx skbs, so SUPPORTS_CLONED_SKBS
flag can be set. Enabling this flag significant reduce number
of copy operation during TCP Tx. This is especially noticeable
on platforms with slower CPU (lower CPU usage brings
profits in better TCP Tx troughput results).
Tested on MIPS with 560 MHz clock
Without CLONED_SKBS flag:
TCP Tx 145 Mb/s (iperf result)
__copy_user_common consumes 12.9% of CPU (result from perf tool)
0% CPU Idle
With CLONED_SKBS flag:
TCP Tx 170 Mb/s (iperf result)
__copy_user_common consumes 1.8% of CPU (result from perf tool)
12% CPU Idle
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a simple interface for platform to perform crash
recovery.
When firmware crashes, wil driver can notify the platform
which can trigger a crash recovery process. During
the process the platform can request a ram dump
from the wil driver as well as control when firmware
recovery will start. This interface allows the platform
to implement a more advanced crash recovery, for
example to reset dependent subsystems in proper order, or
to provide its own notifications during the recovery process.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When network interface is stopping, some resources may
be already released by the network stack, and Rx frames
cause kernel OOPS (observed one is in netfilter code)
Proper solution is to drop packets pending in reorder buffer.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use SMPS disabled as default because FW does not indicate
any support of SMPS.
This change will help STAs out that don’t support SMPS from
sticking on 1SS, since they don’t have method to change it
back to multiple chains.
This change also should not affect power consumption of STAs
supporting SMPS, because they are capable to switch the mode
to dynamic or static either at the end of frame sequence or
by using SMPS action frame.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
"iter" is -1 at the end of the loop and not zero. It means we don't
print a warning message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function can return negative values in case of error.
Its result should be then tested for such case.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 1aaf8efba0ae ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d409ce4 ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mesh Point requires peer security key install when running
in secured mode since it's a type of peer links, otherwise peer
link will be removed due to key install failure.
MFP feature set is required to run Mesh in secured mode and
QCA988X firmware, 10.2.4.70.14-2 and above, is the only one
supporting secured Mesh at this moment.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch is derived from
commit 6301566e0b2d ("ath9k: export HW random number generator"),
We evaluated the entropy of the ADC data on QCA9531, QCA9561, QCA955x,
and AR9340, and it has sufficient quality random data (at least 10 bits
and up to 22 bits of min-entropy for a 32-bit value). We conservatively
assume the min-entropy is 10 bits out of 32 bits. Thus, ATH9K_RNG_BUF_SIZE
is set to 320 (u32) i.e., 1.25 kilobytes of data is inserted to fill up
the pool as soon as the entropy counter becomes 896/4096 (set by random.c).
Since ADC was not designed to be a dedicated HW RNG, we do not want to bind
it to /dev/hwrng framework directly. This patch feeds the entropy directly
from the WiFi driver to the input pool. The ADC register output is only
used as a seed for the Linux entropy pool. No conditioning is needed,
since all the conditioning is performed by the pool itself.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When rx stopped, AR_RX_FILTER should be cleared, but in
ath9k_hw_setrxfilter(), ATH9K_RX_FILTER_CONTROL_WRAPPER will always
be set for ar9462/ar9565.
Fix this by moving the code in ath9k_hw_setrxfilter() to
ath_calcrxfilter().
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This gives a user a chance to know why a firmware load
is failing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
My previous patch incorrectly reported the antenna
for 2x2 devices. It should be a mask instead of
a numeric count. This patch fixes that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWZcQtAAoJEG4XJFUm622bgcMH/1VRwtzAKpYVwAyAN0MtVLxe
uANi0Pw1PmEAeEI3TxEBckEH0JYfpg+aAwX7S8scnQSvLP3FYeC5IcHG551vlh0s
FlkGexcXqGrDqjt8mz8hxqqAmMH9YEVlzj2HJf6YFjNS4K84CEgpaSjaSG8S7Wc8
hTSA5K+XxrnEeX41W7FYmeBFLejisg0gVTkS3ZCe4qYz4Gh1oamoA0pOdU+AYOMy
0XBkCT8fqTVXWLHh9/+J7IZOYrjBl4rVaHofeygEAfSRNNfmmjZXX1R+FCQoJEZC
IOEQ31T64G4A37t2N2RGOhiG+2vckdbPg2JsqJosI1L2OZSBbeGZsVW48w+5cgc=
=GQDA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ath9k_mod_tsf64_tu() function while we could
use div_u64_rem() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful for MCC debugging and bug fixing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of MCC and AP interface, add also NOA attr
that will inform stations about absence of an AP.
There is a chance that some stations will handle
this NOA attr correctly and will know exactly when
AP is present/absent.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case we get BSS_CHANGED_P2P_PS early, from
mac80211, we didn't set NOA timer correctly,
while p2p_ps_vif was NULL.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding NOA attr enable Opportunistic Power Save.
Before we calculate ctwindow but didn't enable oppps.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After queue nullfunc for MCC case, we hit WARN_ON
in xmit.c:2398 while skb priority wasn't set.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use u32 while ath9k_hw_gettsf32() and
ath9k_hw_gen_timer_start() require u32.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AP/GO will aprear after NOA, wait 1ms to be sure AP
could receive/answer this frames.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While mac80211 using null frames when connection polling,
we should queue this frames while NOA could be there, and
AP, P2P_GO could be not present.
Without this patch, with no traffic we often saw disconnections
while we try to send nullfunc when AP/GO wasn't present.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of low HZ before this patch we saw wrong
values in debug message. Print real timeout value.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add/extend debug messages when chanctx used.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In __wmi_send we check if fw is ready at the beginning of the function.
While we wait for the completion of the previous command, system suspend
can be invoked and reset the HW, causing __wmi_send to read from HW
registers while it is not ready.
Taking the wmi_mutex in the reset flow when setting the FW ready bit
to zero will prevent the above race condition.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rates in the tx control rateset do not have the protection
flags applied, so RTS/CTS would never get enabled if requested.
Fix by using the rate flags in the rates returned by
ieee80211_get_tx_rates().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
An error message ath6kl_htc_rxmsg_pending_handler isn't appropate for when
the error is ECANCELED. This could be the result of a perfectly appropriate
RX cancel due to shutdown or suspend. This allows the right cleanup to
continue, but without an alarming error message in this particular case.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
