IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Add power domain control support for the r8a7779 SoC V2.
This adds support for 4 power domains for I/O Devices
together with code that can be used for CPU cores as well.
The only out of the ordinary experience is the need for
ioremap() of SYSC registers. Because of that we need to
execute some init function before setting up the domains.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add r8a7779 PFC function support using the shared PFC code.
Depends on variable bitfield config register patches.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add cache flushing code to the SH-Mobile specific CPU hotplug
implementation. While at it, add a cpu mask to make sure the
cache flushing code is finished in platform_cpu_die() before
letting the SoC-specific code in shmobile_platform_cpu_kill()
proceed with turning off power.
Without this code CPU hotplug offline fails when cache is
enabled on Cortex-A9 based SoCs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the function shmobile_platform_kill_cpu() to allow
SoC specific code to tie in their CPU shutdown code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the low level SMP assembly code for SH-Mobile ARM
from using the INIT to the CPUINIT section. This unbreaks
onlining of CPUs using the CPU hotplug interface:
echo 1 > /sys/devices/system/cpu/cpu1/online
Without this fix the reset vector code used by CPU hotplug
will be freed as init section data and CPU cores cannot
be brought online.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SCIF2 and SCIF4 pin configuration code to
the r8a7779 Marzen board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
The 158MiB memory area was used to support HD
resolution multimedia workloads using the same
legacy memory allocating solution as on SH.
There are no in-tree kernel dependencies on the
158MiB setting, and future development should
reserve and allocate memory using some other
method like for instance CMA.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
* pm-domains:
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
PM / Domains: Provide an always on power domain governor
PM / Domains: Fix default system suspend/resume operations
PM / Domains: Make it possible to assign names to generic PM domains
PM / Domains: fix compilation failure for CONFIG_PM_GENERIC_DOMAINS unset
PM / Domains: Automatically update overoptimistic latency information
PM / Domains: Add default power off governor function (v4)
PM / Domains: Add device stop governor function (v4)
PM / Domains: Rework system suspend callback routines (v2)
PM / Domains: Introduce "save/restore state" device callbacks
PM / Domains: Make it possible to use per-device domain callbacks
After adding PM QoS constraints for the I2C controller in the A4R
domain, that domain can be allowed to be turned off and on by runtime
PM, so remove the "always on" governor from it.
However, the A4R domain has to be "on" when suspend_device_irqs() and
resume_device_irqs() are executed during system suspend and resume,
respectively, so that those functions don't crash while accessing the
INTCS. For this reason, add a PM notifier to the SH7372 PM code and
make it restore power to A4R before system suspend and remove power
from all unused PM domains after system resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
SH7372 uses two independent mechanisms for ensuring that power
domains will never be turned off: the stay_on flag and the "always
on" domain governor. Moreover, the "always on" governor is only taken
into accout by runtime PM code paths, while the stay_on flag affects
all attempts to turn the given domain off. Thus setting the stay_on
flag causes the "always on" governor to be unnecessary, which is
quite confusing.
However, the stay_on flag is currently only set for two domains: A3SP
and A4S. Moreover, it only is set for the A3SP domain if
console_suspend_enabled is set, so stay_on won't be necessary for
that domain any more if console_suspend_enabled is checked directly
in its .suspend() routine. [This requires domain .suspend() to
return a result, but that is a minor modification.] Analogously,
stay_on won't be necessary for the A4S domain if it's .suspend()
routine always returns an error code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Since the SH7372's INTCS in included into syscore suspend/resume,
which causes the chip to be accessed when PM domains have been
turned off during system suspend, the A4R domain containing the
INTCS has to stay on during system sleep, which is suboptimal
from the power consumption point of view.
For this reason, add a new INTC flag, skip_syscore_suspend, to mark
the INTCS for intc_suspend() and intc_resume(), so that they don't
touch it. This allows the A4R domain to be turned off during
system suspend and the INTCS state is resrored during system
resume by the A4R's "power on" code.
Suggested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The sh7372 contains a power domain named A4S which in turn
contains power domains for both I/O Devices and CPU cores.
At this point only System wide Suspend-to-RAM is supported,
but the the hardware can also support CPUIdle. With more
efforts in the future CPUIdle can work with bot A4S and A3SM.
Tested on the sh7372 Mackerel board.
[rjw: Rebased on top of the current linux-pm tree.]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add default value for CONFIG_ARCH_NR_GPIO to Kconfig and remove the
definition in gpio.h.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Saves a tiny amount of code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a name member pointer to struct generic_pm_domain and use it in
diagnostic messages regarding the domain power-off and power-on
latencies. Update the ARM shmobile SH7372 code to assign names to
the PM domains used by it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Current div6 clocks can specify their current parent clocks
from its register value if it is registered
by sh_clk_div6_reparent_register().
This patch modifies all div6 clocks into SH_CLK_DIV6_EXT().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a function deciding whether or not devices should be stopped in
pm_genpd_runtime_suspend() depending on their PM QoS constraints
and stop/start timing values. Make it possible to add information
used by this function to device objects.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
The current generic PM domains code requires that the same .stop(),
.start() and .active_wakeup() device callback routines be used for
all devices in the given domain, which is inflexible and may not
cover some specific use cases. For this reason, make it possible to
use device specific .start()/.stop() and .active_wakeup() callback
routines by adding corresponding callback pointers to struct
generic_pm_domain_data. Add a new helper routine,
pm_genpd_register_callbacks(), that can be used to populate
the new per-device callback pointers.
Modify the shmobile's power domains code to allow drivers to add
their own code to be run during the device stop and start operations
with the help of the new callback pointers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Current fsi-ak4642 was using id_entry name in order to specify
FSI port and ak464x codec.
But it was no sense, no flexibility.
Platform can specify FSI/ak464x pair by this patch.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Keep the ZB clock enabled on sh73a0 to allow the BSC
to access external peripherals hooked up to CS signals.
This is needed to unbreak Ethernet support on sh73a0 boards
such as AG5EVM and Kota2 together with the following patch:
794d78f drivers: sh: late disabling of clocks V2
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix IRQ support on the AG5EVM board. The sh73a0 and the AG5EVM
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke AG5EVM irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Kota2 board support code to
use the recently merged TPU LED driver whenever
possible.
The sh73a0 SoC has 5 TPU hardware blocks each with
4 timer channels which in theory allows a total of
20 LEDs to be controlled by "leds-renesas-tpu"
driver instances. The Kota2 board has 4 LEDs connected
to GPIO pins that also come with TPU pin functions, so
this patch ties up these 4 LEDS and leaves the remaining
3 LEDS for the GPIO based LED driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix IRQ support on the Kota2 board. The sh73a0 and the Kota2
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke Kota2 irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and Kota2 using INTC PINT macros.
With this patch applied the Kota2 ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
sh73a0 PINT support is included in 3.2-rc but the Kota2 board
code does not make use of this shared code base without this
patch. Without this patch kota2 on-board ethernet is broken.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some clocks can select its parent clock by CPG register.
But it might have been modified by boot-loader or something.
This patch removed fixed initial parent clock,
and setup it from their current register settings.
It works on div6 reparent clocks for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
dsipck clock is controled by CLKDEV_ICK_ID() in clock-shxxx.
dsi0p_clk/dsi1p_clk naming is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
Fix build regression introduced by commit 056879d2f2
(ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving
the intialization of the A3SP domain to a separate function and
providing an empty definition of it for CONFIG_PM unset.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert the SMP shmobile platforms to use gic_handle_irq() instead
of the assembly macro.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Even when CONFIG_MULTI_IRQ_HANDLER is selected, the core code
requires the arch_irq_handler_default macro to be defined as
a fallback.
It turns out nobody is using that particular feature as both PXA
and shmobile have all their machine descriptors populated with
the interrupt handler, leaving unused code (or empty macros) in
their entry-macro.S file just to be able to compile entry-armv.S.
Make CONFIG_MULTI_IRQ_HANDLER exclusive wrt arch_irq_handler_default,
which allows to remove one test from the hot path. Also cleanup both
PXA and shmobile entry-macro.S.
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The SH7372 PM domain initialization routine calls pd_power_up()
that executes the domain's .resume() callback, if present, and for
the A4R domain this callback attepmts to restore the INTCS state from
uninitialized data. To avoid that, introduce __pd_power_up() that
will only execute the domain's .resume() callback if its second
argument is 'true' and make the SH7372 PM domain initialization
use it with 'false' as its second argument. Redefine pd_power_up()
as a wrapper around __pd_power_up().
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tracked-down-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
bonito board needs some settings by pmic which use i2c access.
It is dependent on the device to be used.
This patch adds standard settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
devices enable/disable are controled by dip-switch on bonito board.
If bonito core board is connected to base board,
you can check the settings from FPGA.
This patch adds basic code and controls SCIFA5 settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If "no_suspend_irq" is used on the sh7372 Mackerel board
with v3.2-rc1 then Suspend-to-RAM fails because the serial
console tries to write to the SCIF driver even though the
power domain is turned off.
This patch checks the state of "console_suspend_enabled"
to see if A3SP should be forced enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Don't skip debugging output upon earlier loop termination in pd_power_up().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'rmobile-latest' of git://github.com/pmundt/linux-sh: (21 commits)
ARM: mach-shmobile: ag5evm needs CONFIG_I2C
ARM: mach-shmobile: sh73a0 and AG5EVM PINT support
ARM: mach-shmobile: Add support for PINT though INTC macros
ARM: mach-shmobile: SDHI0 GPIO hotplug for AG5EVM
ARM: mach-shmobile: Use common INTC IRQ code on sh73a0
ARM: mach-shmobile: Use common INTC IRQ code on sh7372
ARM: mach-shmobile: Use common INTC IRQ code on sh7377
ARM: mach-shmobile: Use common INTC IRQ code on sh7367
ARM: mach-shmobile: sh73a0 GPIO IRQ support
ARM: sh7372 ap4evb NOR Flash USB boot fix
ARM: mach-shmobile: sh7372 Mackerel NOR Flash USB boot fix
sh: intc: Allow triggering on both edges for ARM SoCs
ARM: mach-shmobile: Break out INTC IRQ code
ARM: mach-shmobile: Kota2 SDHI0 and SDHI1 support
ARM: mach-shmobile: Kota2 SCIFA4 and SCIFB support
ARM: mach-shmobile: Kota2 MMCIF support
ARM: mach-shmobile: Kota2 GPIO LEDs support
ARM: mach-shmobile: Kota2 GPIO Keys support
ARM: mach-shmobile: Kota2 KEYSC support
ARM: mach-shmobile: Kota2 SCIFA2 and SMSC911X support
...
ag5evm implements a backlight control, using an I2C controller, therefore
it needs CONFIG_I2C to fix this make failure
arch/arm/mach-shmobile/built-in.o: In function `lcd_on':
pfc-sh73a0.c:(.text+0x2334): undefined reference to `i2c_get_adapter'
pfc-sh73a0.c:(.text+0x2370): undefined reference to `i2c_transfer'
(ignore pfc-sh73a0.c) and to build successfully.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support PINT on sh73a0 and AG5EVM using INTC PINT macros.
With this patch applied the AG5EVM ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a INTC_PINT() macro with various helper bits to allow SoCs
like sh73a0 to suppor the PINT hardware using regular INTC tables.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement GPIO hotplugging via TMIO_MMC_HAS_COLD_CD for
AG5EVM SDHI0. This is possible now when INTCA is used for
IRQ triggering on sh73a0. Without INTCA IRQ support we are
left with the GIC hardware block that does not support
dealing with active low interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve IRQ triggering support by making use of the macro
INTC_IRQ_PINS_32() for INTCA on sh73a0. Unfortunately it
is not as easy as just using the macro as-is, we need to
do mask and unmaks in the GIC but configure other bits
and ack in INTCA. Update GPIO IRQ mappings while at it.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh73a0 GPIO IRQs by making use
of the PFC GPIO IRQ feature. Only IRQ pins are supported
at this time. In the future when PINT interrupts also are
supported properly we can easily extend the table with such
information. Also, the sh73a0 is currently making use of
the GIC for external interrupt which is rather unflexible
when it comes to triggering configuration at this point.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on ap4evb.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Always use CS0 shadow area for NOR flash instead of regular CS0
memory area on Mackerel.
When booting from CS0 NOR Flash the regular CS0 memory area is
available, but when booting via USB the MASK ROM gets mapped to
0x0 which gets in the way for the NOR Flash. Always using CS0
shadow area works well for both NOR Flash boot and USB boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTC_IRQ_PINS_16() and INTC_IRQ_PINS_32() to mach/intc.h.
These macros define 16 or 32 external IRQ pins on a certain
memory base address. Can be used with INTCA or INTCS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (144 commits)
[media] saa7134.h: Suppress compiler warnings when CONFIG_VIDEO_SAA7134_RC is not set
[media] it913x [VER 1.07] Support for single ITE 9135 devices
[media] Support for Terratec G1
[media] cx25821: off by one in cx25821_vidioc_s_input()
[media] media: tea5764: reconcile Kconfig symbol and macro
[media] omap_vout: Add poll() support
[media] omap3isp: preview: Add crop support on the sink pad
[media] omap3isp: preview: Rename min/max input/output sizes defines
[media] omap3isp: preview: Remove horizontal averager support
[media] omap3isp: Report the ISP revision through the media controller API
[media] omap3isp: ccdc: remove redundant operation
[media] omap3isp: Fix memory leaks in initialization error paths
[media] omap3isp: Add missing mutex_destroy() calls
[media] omap3isp: Move *_init_entities() functions to the init/cleanup section
[media] omap3isp: Move media_entity_cleanup() from unregister() to cleanup()
[media] MFC: Change MFC firmware binary name
[media] vb2: add vb2_get_unmapped_area in vb2 core
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
[media] media: ov6650: stylistic improvements
...
