IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.
Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf9844636be ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.
This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pre qca99X0 chipsets follows the model where dynamically allocate
memory for frag desc on getting new skb for TX. But, this is not
going to be the case in qca99X0. It expects frag desc memory to be
allocated at boot time and let the driver to reuse allocated memory
after every TX completion. So there won't be any dynamic frag memory
memory allocation in qca99X0 during data transmission.
qca99X0 hardware doesn't need fragment desc address to be programmed
in msdu descriptor for every data transaction. It needs to know only
starting address of fragment descriptor at the time of the boot.
During data transmission, qca99X0 hardware can retrieve corresponding
frag addr by adding programmed frag desc base addr + msdu id.
Allocate continuous fragment descriptor memory (same size as number of
descriptor) at the time of target initialization and configure allocated
dma address to the target via HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG.
How this is allocated continuous memory is going to be used is not
covered in this patch. It just allocates memory and hand over to firmware.
If we don't do it at init time, qca99X0 will stall when firmware tries
to do TX.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 fw supports upto 4 spatial stream. Limit max spatial
stream to 4 for 10.4 firmware and to 3 for non 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware swba event payload has space to accommodate upto
512 client traffic indication info & one p2p noa descriptor.
It's is not matching with exiting swba event format defined for
non 10.4 firmware. Non 10.4 firmware swba event format is designed
to support only upto only 128 client and four p2p notice of absence
descriptor.
following changes are done in this patch to enable ath10k to handle
10.4 firmware swba event,
- link generic ath10k_wmi_event_host_swba() to handle 10.4 swba
event in 10.4 wmi rx handler.
- add 10.4 specific swba event structure wmi_10_4_host_swba_event.
- new function ath10k_wmi_10_4_op_pull_swba_ev() to parse
10.4 swba event.
- increase tim_bitmap[] size in ath10k_vif to 64 to hold 512 station
power save state.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define 10.4 wmi init command structure and introduce new function
ath10k_wmi_10_4_op_gen_init() to fill default values for each field
which goes as part of wmi init cmd to 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
BMI parameter value to execute downloaded otp binary
is different for QCA99X0. Have a member in hw_params
to hold hw specific BMI param.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In practice there's no point in having a copy of
chanctx_conf.
Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().
The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.
I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now only a single fixed tx rate or nss was
allowed to be set.
The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.
This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.
Depending on firmware revisions some combinations
may crash firmware so use with care, please.
This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.
These work:
iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9
These won't work:
iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
iw wlan0 set bitrates vht-mcs-5 2:7-9
(note the invalid VHT MCS ranges)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices differ slightly and require different
board files. If wrong board data is used they
crash or behave incorrectly.
These devices can be differentiated by looking at
PCI subsystem device id. That is the case for
qca61x4 devices at least.
The board specific filename is constructed as:
board-<bus>-<id>.bin
For PCI in particular it is:
board-pci-<vendor>:<dev>:<subsys_vendor>:<subsys_dev>.bin
These files are looked in device/hw specific
directories. Hence for Killer 1525 (qca6174 hw2.1)
ath10k will request:
/lib/firmware/ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin
To not break any existing setups (e.g. in case
some devices in the wild already have subsys ids)
if a board specific file isn't found a generic one
is used which is the one which would be used until
now. This guarantees that after upgrading a driver
device will not suddenly stop working due to
now-missing specific board file. If this is the
case a "fallback" string is appended to the info
string when driver boots.
Keep in mind this is distinct from cal-pci-*.bin
files which contain full calibration data and MAC
address. Cal data is aimed at systems where
calibration data is stored out of band, e.g. on
nand flash instead of device EEPROM - an approach
taken by some AP/router vendors.
Board files are more of a template and needs some
bits to be filled in by the OTP program using
device EEPROM contents.
One could argue to map subsystem ids to some board
design codename strings instead of using raw ids
when building the board filename. Using a mapping
however would make it a lot more cumbersome and
time consuming (due to how patches propagate over
various kernel trees) to add support for some new
device board designs. Adding a board file is a lot
quicker and doesn't require recompilation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix the regerssion introduced after "ath10k_wmi_requests_stats()
call to use more stat bits", both the 10.2.X FW and community FW 10.1.X
will return time out when access the fw_stats with the STAT_VDEV and
STAT_PDEV. Add the condition to use different fw_stats mask for different
FW versions.
Fixes: 7777d8c7ef6f ("ath10k: implement fw stats for wmi-tlv")
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code was a bit convoluted. Clean it up and
prepare for future changes.
While at it this fixes incorrect verification of
'single nss' case when ss2 rates were missing
while ss1 and ss3 were requested resulting in
nss=3 being set:
iw wlan1 set bitrates legacy-5 ht-mcs-5 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23 vht-mcs-5 1:0-9 3:0-9
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5f3 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently number of tdls vdevs supported by firmware
is hardcoded. For future usage it is stored in ath10k
structure based on defined value.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the station kickout threshold is also counting software
reries (Default sw count in firmware is 16), increasing the threshold
to try with atleast 20 data frames before kicking out the station.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions (e.g. qca6174 with fw73)
don't deliver beacons to host reliably. This
causes random disconnects even in perfect
conditions. This is most visible with
multi-channel operation.
All available firmware revisions seem to support
beacon miss offloading so there shouldn't be any
problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.
Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.
To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware supports vdev stats.
This patch adds support for it in the debug
frontend.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.
The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.
Used TX_USAGE flag to set default key for stations.
Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware and firmware (qca6174 hw3.0+ and fw
266+) are capable of full aggregation rx
reordering. If it's enabled then Rx is handled via
a new, separate htt event.
The rx ring behaviour is changed a little to
support the new rx scheme. These changes shouldn't
affect qca988x performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to share the
ath10k_skb_cb with Rx path. The Rx path doesn't
need to keep any mac80211's data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal cooling device support is added to control the temperature
by throttling the data transmission for the given duration. Throttling
is done using hw MAC quiet time setting. Period, duration and offset
from TBTT can be set up to quiet the MAC transmits for the required duty
cycle (% of quiet duration). The thermal device allows user to configure
duty cycle.
The quiet params are derived as follows.
period = max(25TU, beacon interval / number of bss)
duration = period * duty cycle / 100
Quiet mode can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to manage firmware differences, we should not use
ATH10K_FW_FEATURE_WMI_10X outside ath10k_core_init_firmware_features(). To
achieve that create new field ar->max_num_vdevs and set it based on wmi op
version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.
It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.
Till now calibration was done at 30 seconds.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will make it possible to easily support
different hardware with different uart pin
configuration.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to extend the list of
supported hardware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for reading calibration data from Device Tree.
It looks for the calibration data in Device Tree if it can't find it
in a file. If there's no node in Device Tree, ath10k will try to find the
calibration data from OTP.
The node for the calibration data should be defined like this:
pci {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
ath10k@0,0 {
reg = <0 0 0 0 0>;
device_type = "pci";
qcom,ath10k-calibration-data = [ 01 02 03 ... ];
};
};
};
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
