IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If max1027_wait_eoc() fails then call iio_device_release_direct_mode()
before returning.
Fixes: a0e831653e ("iio: adc: max1027: Introduce an end of conversion helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YsbztVuAXnau2cIZ@kili
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: fc167f6248 ("iio: add support of the max1027")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-24-jic23@kernel.org
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
-----BEGIN PGP SIGNATURE-----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=htmG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO new device and feature support for the 5.16 cycle
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
* tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (148 commits)
iio: imx8qxp-adc: mark PM functions as __maybe_unused
iio: pressure: ms5611: Make ms5611_remove() return void
iio: potentiometer: max5487: Don't return an error in .remove()
iio: magn: hmc5843: Make hmc5843_common_remove() return void
iio: health: afe4403: Don't return an error in .remove()
iio: dac: ad5686: Make ad5686_remove() return void
iio: dac: ad5592r: Make ad5592r_remove() return void
iio: dac: ad5446: Make ad5446_remove() return void
iio: dac: ad5380: Make ad5380_remove() return void
iio: accel: mma7455: Make mma7455_core_remove() return void
iio: accel: kxsd9: Make kxsd9_common_remove() return void
iio: accel: bmi088: Make bmi088_accel_core_remove() return void
iio: accel: bmc150: Make bmc150_accel_core_remove() return void
iio: accel: bma400: Make bma400_remove() return void
drivers:iio:dac:ad5766.c: Add trigger buffer
iio: triggered-buffer: extend support to configure output buffers
iio: kfifo-buffer: Add output buffer support
iio: Add output buffer support
iio: documentation: Document scd4x calibration use
drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
...
Return -ETIMEDOUT on timeout instead of success.
Fixes: 1f7b4048b3 ("iio: adc: max1027: Use the EOC IRQ when populated for single reads")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
External triggers do not necessarily need the EOC interrupt to be
populated to work properly. The end of conversion status may either come
from an interrupt or from a sufficient enough extra delay. IRQs are not
mandatory so move the triggered buffer setup out of the IRQ condition
and add the logic to wait enough time for all the requested conversions
to be in the device's FIFO.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-17-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no reason to limit this driver to its internal trigger. The
only difference being, when using an external trigger, the sample
conversion must be manually started.
Drop the ->validate_trigger() hook in order to allow other triggers to
be bound.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-16-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
So far the End-Of-Conversion interrupt was only used in conjunction with
the internal trigger to process the data. Let's extend the use of this
interrupt handler to support regular single-shot conversions as well.
Doing so requires writing our own hard IRQ handler. This handler has to
check if buffers are enabled or not:
*** Buffers disabled condition ***
This means the user requested a single conversion and the sample is
ready to be retrieved.
-> This implies adding the relevant completion boilerplate.
*** Buffers enabled condition ***
Triggers are used. So far there is only support for the internal
trigger but this trigger might soon be attached to another device as
well so it is the core duty to decide which handler to call in order
to process the data. The core will decide to either:
* Call the internal trigger handler which will extract the data that
is already present in the ADC FIFOs
or
* Call the trigger handler of another driver when using this trigger
with another device, even though this call will be slightly delayed
by the fact that the max1027 IRQ is a data-ready interrupt rather
than a real trigger:
-> The new handler will manually inform the core about the trigger
having transitioned by directly calling iio_trigger_poll() (which
iio_trigger_generic_data_rdy_poll() initially did).
In order for the handler to be "source" agnostic, we also need to change
the private pointer and provide the IIO device instead of the trigger
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-15-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The threaded handler is not populated, this means there is nothing
running in process context so let's switch to the regular
devm_request_irq() call instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-14-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For now this helper only waits for the maximum duration of a single
conversion.
In practice, a "temperature measurement" will take twice this
time because it will also carry another analog conversion but as here we
will only care about the temperature conversion which happens first, we
can still only wait for a single sample and get the right data.
This helper will soon be improved to properly handle the end of
conversion interrupt as well as a higher number of samples.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create a max1027_read_scan() helper which will make clearer the future IRQ
handler updates (no functional change).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-12-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When hardware buffers are enabled (the cnvst pin being the trigger), one
should not mess with the device state by requesting a single channel
read.
There is already a iio_buffer_enabled() check in *_read_single_value()
to merely prevent this situation but the check is inconsistent since
buffers can be enabled after the if clause anyway. Instead, use the core
mutex by calling iio_device_claim/release_direct_mode().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-11-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We don't expect the (hardware) cnvst trigger to be enabled at boot time,
this is a user choice made in sysfs and there is a dedicated callback to
enable/disable this trigger. Hence, we can just ensure it is disabled in
the probe at initialization time and then assume that whenever a
->read_raw() call happens, the trigger has been disabled and conversions
will start on register write.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-9-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The call to max1027_enable_trigger() is the same in both cases thanks to
the 'state' variable, so factorize a little bit to simplify the code and
explain why we call this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-8-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are two ways to physically trigger a conversion:
- A falling edge on the cnvst pin
- A write operation on the conversion register
Let's create a helper for this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-7-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it clear that the *_set_trigger_state() hook is responsible for
cnvst based conversions by renaming the helper. This may avoid
confusions with software trigger support that is going to be
introduced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-6-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.
The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.
For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.
Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Memory allocation errors automatically trigger the right logs, no need
to have our own.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow checkpatch.pl's main advices before hacking into the driver, mainly:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int *' to bare use of 'unsigned *'
CHECK: Comparison to NULL could be written "!foo"
CHECK: Alignment should match open parenthesis
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The macro MAX1X29_CHANNELS() already calls MAX1X27_CHANNELS().
Calling MAX1X27_CHANNELS() before MAX1X29_CHANNELS() in the definition
of MAX1X31_CHANNELS() declares the first 8 channels twice. So drop this
extra call from the MAX1X31 channels list definition.
Fixes: 7af5257d84 ("iio: adc: max1027: Prepare the introduction of different resolutions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
10-bit devices must shift the value twice.
This is not needed anymore on 12-bit devices.
Fixes: ae47d009b5 ("iio: adc: max1027: Introduce 12-bit devices support")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO ADC group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use cocci semantic patch:
@@
expression trigger, P;
@@
trigger = devm_iio_trigger_alloc(P, ...);
...
- trigger->dev.parent = P;
To remove trigger->dev.parent, since it is set by default.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-3-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These just prevent the driver being used with ACPI PRP0001
and provide no major benefits.
Part of clearing these out in general in IIO to avoid cut and paste
repetition in new drivers. Also include mod_devicetable.h as we
directly make use of of_device_id which is defined in there.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment is done in the iio_device_register() function.
There is a fair amount of drivers that currently manually assign the
of_node of the IIO device. All but 4 of them can make use of the automatic
assignment though.
The exceptions are:
* mxs-lradc-adc: Which uses the of_node of the parent of the parent.
* stm32-dfsdm-adc, stm32-adc and stm32-dac: Which reference the of_node
assigned to the IIO device before iio_device_register() is called.
All other drivers are updated to use automatic assignment. This reduces
the amount of boilerplate code involved in setting up the IIO device.
The patch has mostly been auto-generated with the following semantic patch
// <smpl>
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(&parent, ...)
...
-indio_dev->dev.of_node = parent.of_node;
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(parent, ...)
...
-indio_dev->dev.of_node = parent->of_node;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max1027/29/31 series returns the measured voltages with a
resolution of 10 bits. There is a very similar series, max1227/29/31
which works identically but uses a resolution of 12 bits. Prepare the
support for these chips by turning the 'depth' into a macro parameter
instead of hardcoding it everywhere. Also reorganize just a bit the
macros at the top to avoid repeating tens of lines when adding support
for a new chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip has a 'start conversion' and a 'end of conversion' pair of
pins. They can be used but this is absolutely not mandatory as regular
polling of the value is totally fine with the current internal
clocking setup. Turn the interrupts optional and do not error out if
they are not inquired in the device tree. This has the effect to
prevent triggered buffers use though.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, only write operations were supported. Force two bytes read
operation when reading, which should fit most of the development
purposes. Of course, extended operations like buffered reads on
multiple channels or even temperature + voltage reads will not be read
entirely. Usually, just starting a new operation will work but in any
case a software reset (done through the debufs interface too) will
return the device in a usable state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new iio_trigger_validate_own_device() to verify that the trigger
can only be attached to the matching IIO device rather than using a custom
variant.
While the implementation of iio_trigger_validate_own_device() and the
custom variant and are not identical their behaviour is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adding missing indio_dev->dev.of_node references to allow iio consumers
to access the device channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has an OF id table but the .of_match_table is not set so
the SPI core can't do an OF style match and the table was unused.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver add partial support of the
maxim 1027/1029/1031. Differential mode is not
supported.
It was tested on armadeus apf27 board.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
