IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The original core reset and disable routines do not work always
on running system. These routines were updated to properly reset
a core. When module is unloaded the device is put into download
state where all necessary cores have been reset. This will make
sure the device is in idle mode after module unload.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New bus layers like pcie require nvram parsing routines which are
the same routines as being used by sdio. Make these routines common
in the new file nvram.c. Update sdio to use these routines and
simplify the nvram upload process. Also add memory validation check
for downloaded firmware and nvram in debug mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx head write-back registers are not cleared during an FLR or VF reset.
As a result a configuration that had head write-back enabled can leave the
registers set after the driver is unloaded. If the next driver loaded doesn't
use the write-back registers this can lead to a bad configuration where
head write-back is enabled, but the driver didn't request it.
To avoid this situation the PF should be resetting the Tx head write-back
registers when the VF requests a reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the QDE bits are set for a VF before the Rx
queues are enabled. As such we avoid head of line blocking in the event
that the VF stops cleaning Rx descriptors for whatever reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 14 ++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 7 ++++---
2 files changed, 18 insertions(+), 3 deletions(-)
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check value returned by dma_map_page. The patch
fixes this.
v2: Removed the bugfix for non-bug ;-) (thanks Sathya)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <Sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x driver in its pci shutdown() callback releases its pci bars (in the
same manner it does during its pci remove() callback).
During a system reboot while VFs are enabled, its possible for the VF's remove
to be called (as a result of pci_disable_sriov()) after its shutdown callback
has already finished running; This will cause a paging request fault as the VF
tries to access the pci bar which it has previously released, crashing the
system.
This patch further differentiates the shutdown and remove callbacks, preventing the
pci release procedures from being called during shutdown.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, use the tail of the RXQ to pick the associated RXQ entry
This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As be2net is used even by the 40Gbps Skyhawk-R chip
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the GET_HSW_CONFIG cmd, the "pport" field must be set only while
querying the switch mode. When the "pport" field is set, the
"interface_id" field must be set to the port number, otherwise, it
must be set to adapter->if_handle.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhine_reset_task() misses to disable the tx scheduler upon reset,
this can lead to a crash if work is still scheduled while we're resetting
the tx queue.
Fixes:
[ 93.591707] BUG: unable to handle kernel NULL pointer dereference at 0000004c
[ 93.595514] IP: [<c119d10d>] rhine_napipoll+0x491/0x6
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO requires VLANs to be removed before aggregation can occur.
The Synopsys EMAC does not strip VLAN tags so this must be
done by the driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse warning about function declared static.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `orion_mdio_probe':
drivers/net/ethernet/marvell/mvmdio.c:228: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes unhandled register write in gianfar_ethtool.c.
Fixes following endianess related functional issues,
reported by sparse as well, i.e.:
gianfar_ethtool.c:1058:33: warning:
incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] value
got restricted __be32 [usertype] ip4src
gianfar_ethtool.c:1164:33: warning:
restricted __be16 degrades to integer
gianfar_ethtool.c:1669:32: warning:
invalid assignment: ^=
left side has type restricted __be16
right side has type int
Solves all the sparse warnings for mixig normal pointers
with __iomem pointers for gianfar_ptp.c, i.e.:
gianfar_ptp.c:163:32: warning:
incorrect type in argument 1 (different address spaces)
expected unsigned int [noderef] <asn:2>*addr
got unsigned int *<noident>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete a variable that is at most only assigned to a constant, but never
used otherwise. In this code, it is the variable result that is used for
the return code, not rc.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e Physical Function (PF) driver will allow the
Virtual Function (VF) driver to configure its own VLAN filters if no port
VLAN filter has been configured. This leads to the possibility of the
administrator setting a port VLAN filter for the VF after the VF has already
configured its own VLAN filters. This leads to a conflict that can only be
resolved by reloading the VF driver. When the conflicting administrative
command is detected in setting the port VLAN then log a message indicating to
the system administrator that he must now reload the VF driver for the new
port VLAN settings to take effect.
Change-Id: I8de73b885d944a043aff32226297e4249862bcad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use vxlan_dellink() handler in vxlan_exit_net(), since
i) we're not in fast-path and we should be consistent in dismantle
just as we would remove a device through rtnl ops, and more
importantly, ii) in case future code will kfree() memory in
vxlan_dellink(), we would leak it right here unnoticed. Therefore,
do not only half of the cleanup work, but make it properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can create a vxlan device with an explicit underlying carrier.
In that case, when the carrier link is being deleted from the
system (e.g. due to module unload) we should also clean up all
created vxlan devices on top of it since otherwise we're in an
inconsistent state in vxlan device. In that case, the user needs
to remove all such devices, while in case of other virtual devs
that sit on top of physical ones, it is usually the case that
these devices do unregister automatically as well and do not
leave the burden on the user.
This work is not necessary when vxlan device was not created with
a real underlying device, as connections can resume in that case
when driver is plugged again. But at least for the other cases,
we should go ahead and do the cleanup on removal.
We don't register the notifier during vxlan_newlink() here since
I consider this event rather rare, and therefore we should not
bloat vxlan's core structure unecessary. Also, we can simply make
use of unregister_netdevice_many() to batch that. fdb is flushed
upon ndo_stop().
E.g. `ip -d link show vxlan13` after carrier removal before
this patch:
5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default
link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300
^^^^^
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan gets the same netdev features except vlan filter.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent writes to an adapter that has been detected as removed
by a previous failing read. This also fixes some include file
ordering confusion that this patch revealed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer. Use boolean values for
boolean returns instead of 0 and 1.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Temporarily provide macros for calling the new static inline
accessors until all references are changed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBE_DOWN. This did not work before
introduction of the __IXGBE_REMOVING bit, because of overloading
of __IXGBE_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBE_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bit, __IXGBE_REMOVING, to indicate that the module is being
removed. The __IXGBE_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBE_DOWN
and __IXGBE_REMOVE. Notably, setting either bit will prevent service
task execution.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.30-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some un-necessary parenthesis.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some whitespace and comment issues.
Change-ID: I1587599e50ce66fd389965720e86f9e331d86643
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this message mean something, rather than just spitting out a VSI id
without any context whatsoever.
Change-ID: Iafb906c6db46d4b5dcbe84adc9ed44730d08bd42
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where the queue was not associated with the right set-up
within the hardware. The fix is to use the right QTX_CTL VSI type
when associating it to the VSI.
Change-ID: I65ef6c5a8205601c640a6593e4b7e78d6ba45545
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This write done at the end of VF reset and should not be performed here.
Change-ID: I4d89813b68c6173184293868a6f26cf559bc2405
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chains indicate that vxlan_fdb_parse() is
under rtnl_lock protection. So if we use __dev_get_by_index()
instead of dev_get_by_index() to find interface handler in it,
this would help us avoid to change interface reference counter.
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_add()
vxlan_fdb_add()
vxlan_fdb_parse()
rtnl_unlock()
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_del()
vxlan_fdb_del()
vxlan_fdb_parse()
rtnl_unlock()
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chain indicates that eql_ioctl(), eql_enslave(),
eql_emancipate(), eql_g_slave_cfg() and eql_s_slave_cfg() are
protected under rtnl_lock. So if we use __dev_get_by_name() instead
of dev_get_by_name() to find interface handlers in them, this would
help us avoid to change interface reference counters.
dev_ioctl()
rtnl_lock()
dev_ifsioc()
eql_ioctl()
eql_enslave()
eql_emancipate()
eql_g_slave_cfg()
eql_s_slave_cfg()
rtnl_unlock()
Additionally we also change their return values from -EINVAL to
-ENODEV in case that interfaces are no found.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chain indicates that bond_do_ioctl() is protected
under rtnl_lock. If we use __dev_get_by_name() instead of
dev_get_by_name() to find interface handler in it, this would
help us avoid to change reference counter of interface once.
dev_ioctl()
rtnl_lock()
dev_ifsioc()
bond_do_ioctl()
rtnl_unlock()
Additionally we also change the coding style in bond_do_ioctl(),
letting it more readable for us.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that the ecm and r8152 drivers couldn't coexist.
- Remove the devices from the blacklist of relative drivers.
- Remove usb_driver_set_configuration() from r8152 driver.
- Modify the id_table of the r8152 driver for the vendor mode only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings and error:
- WARNING: usb_free_urb(NULL) is safe this check is probably not required
- WARNING: kfree(NULL) is safe this check is probably not required
- ERROR: do not use C99 // comments
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 could support RTL8153. Update the relative descriptor.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_mii_register() and register_netdev() both return appropriate error
codes for the failures they would encounter, propagate this error code
instead of overriding the value with -ENOTSUPP which is not the correct
error code to return.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of new dm96xx variants now exist.
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets. Add a rx_dropped field and use it where
netdev->stats was modified directly out of the stats update function.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets.
Minor whitespace fixes to match the style in alx.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets.
Minor whitespace fixes to match the style in alx.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch bnx2x will configure the PF to perform Tx switching on
out-going traffic as soon as SR-IOV is dynamically enabled and de-activate
it when it is disabled.
This will allow VFs to communicate with their parent PFs.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
Oleg Moroz added support for a new PCI card to the generic SJA1000 PCI
driver, Guenter Roeck's patch limits the flexcan driver to little
endian arm (and powerpc) and I fixed a sparse warning found by the
kbuild robot in the ti_hecc driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 60e453a940 ("USBNET: fix handling padding packet")
added an extra SG entry in case padding is necessary, but
failed to update the initialisation of the list. This can
cause list traversal to fall off the end of the list,
resulting in an oops.
Fixes: 60e453a940 ("USBNET: fix handling padding packet")
Reported-by: Thomas Kear <thomas@kear.co.nz>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c466a9b2b3
(net: 3com: slight optimization of addr compare)
cause a warning: "passing argument 1 of 'ether_addr_equal'
from incompatible pointer type", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6878f79a8b
(net: qlcnic: slight optimization of addr compare)
cause a warning "sparse: incorrect type in argument 2
(different type sizes)", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_error() in case of a TX error tries to print a message using 2 dev_err()
calls with the first string not finished by '\n', so that the resulting message
would inevitably come out garbled, with something like "3net eth0: " inserted
in the middle. Avoid that by merging 2 calls into one.
While at it, insert an empty line after the nearby declaration.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the implementation is meaningless - once again, we take the
slave structure and use it after we've exited RCU critical section.
Fix this by removing the rcu_read_lock() from __get_active_agg(), and
ensuring that all its callers are holding RCU.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the RCU read lock usage is just wrong - it gets the slave struct
under RCU and continues to use it when RCU lock is released.
However, it's still safe to do this cause we didn't need the
rcu_read_lock() initially - all of the __get_first_agg() callers are either
holding RCU read lock or the RTNL lock, so that we can't sync while in it.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, its usage is just plainly wrong. It first gets a slave under
RCU, and, after releasing the RCU lock, continues to use it - whilst it can
be freed.
Fix this by ensuring that bond_3ad_set_carrier() holds RCU till it uses its
slave (or its agg).
Fixes: be79bd048a ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enabling BIT_9 while configuring hardware LRO allows adapter to
perform LRO even if destination IP address is not programmed in adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add __QLCNIC_SRIOV_ENABLE bit check before doing SRIOV cleanup
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored code to handle beaconing test for all adapters.
o Use GET_LED_CONFIG mailbox command for 83xx/84xx series adapter
to detect current beaconing state of the adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o MAC learning will be done for SRIOV PF to help program VLAN filters
onto adapter. This will help VNIC traffic to flow through without
flooding traffic.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o By default, SRIOV PF will have promiscous mode on.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o On enabling VF flood bit, PF driver will be able to receive traffic
from all its VFs.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter should allow vlan traffic only for vlans configured on a VF.
On configuring any vlan mode from VF, adapter will allow any vlan
traffic to pass for that VF. Do not allow VF to configure this mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_attach_direct() may now attach to a generic 10G driver. It can
also be used exactly as phy_connect_direct(), which will be useful
when using of_mdio, as phy_connect (and therefore of_phy_connect)
start the PHY state machine, which is currently irrelevant for 10G
PHYs.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very incomplete, but will allow for binding an ethernet controller
to it.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then other generic phy driver such as generic 10g phy driver can join it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a bunch of whole lot of namespace issues with the Broadcom bnx2x driver
found by running 'make namespacecheck'
* global variables must be prefixed with bnx2x_
naming a variable int_mode, or num_queue is invitation to disaster
* make local functions static
* move some inline's used in one file out of header
(this driver has a bad case of inline-itis)
* remove resulting dead code fallout
bnx2x_pfc_statistic,
bnx2x_emac_get_pfc_stat
bnx2x_init_vlan_mac_obj,
Looks like vlan mac support in this driver was a botch from day one
either never worked, or not implemented or missing support functions
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If used 64 bit compiler GCC warns that:
drivers/net/ethernet/smsc/smc91x.c:1897:7:
warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
This patch fixes this by changing typecast from "unsigned int" to "unsigned long"
CC: "David S. Miller" <davem@davemloft.net>
CC: Jingoo Han <jg1.han@samsung.com>
CC: netdev@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new device IDs and assigning generic function/variable
names instead of using device-id specific names.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use the native GRO handling of encapsulated protocols on
mlx4, we need to call napi_gro_receive() instead of netif_receive_skb()
unless busy polling is in action.
While we are at it, rename mlx4_en_cq_ll_polling() to
mlx4_en_cq_busy_polling()
Tested with GRE tunnel : GRO aggregation is now performed on the
ethernet device instead of being done later on gre device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc is a limited resource. Don't use it unnecessarily.
It seems this allocation should work with kcalloc.
Remove unnecessary memset(,0,) of buf as it's completely
overwritten as the previously only unset field in
struct qlcnic_pci_func_cfg is now set to 0.
Use kfree instead of vfree.
Use ETH_ALEN instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know how large "tp->vlan_shift" is but static checkers worry
about shift wrapping bugs here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disassociate in managed mode, we flush the queues
after mac80211 has already removed the station.
During that time, the pointer to ieee80211_sta to the
fw_id_to_mac_id map is -EINVAL. In that case we should not
set the station as being drained when the last Tx of this
station has exited the shared Tx queue since we are
flushing all the queues anyway.
The draining logic is meant to be used in GO / AP mode only.
In GO / AP mode, we set -EBUSY in the fw_id_to_mac_id map.
This is why testing the ieee80211_sta pointer in the
fw_id_to_mac_id map with IS_ERR isn't enough to set the
station as draining, we need to check that it is -EBUSY.
The only impact of the bug was a print:
Drained sta 1, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
If we can't switch to a column because no rates are supported
in that column this led to a state where the search cycle
got stuck and never ended. This in turn also led to aggregation
not being turned on. Fix this by marking a column as
visited if we can't switch to it.
Reported-and-tested-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power settings need to be updated after a binding flow is done
and before quota calculations. This was missing in the start_ap_ibss()
flow. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The state variable was not set to false in case of a failure to
complete the start_ap_ibss() flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
That code has been around for ages without being used.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a huge mess currently, that is really hard to read. This cleanup
doesn't touch the logic at all, it only breaks easy-to-fix long lines and
updates comment styles.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and now i40evf.
Most notable is Jacob's patch to add PTP support to i40e.
Mitch cleans up additional memcpy's and use struct assignment instead.
Then fixes long lines to appease checkpatch.pl. Mitch then provides
a fix to keep us from spamming the log with confusing errors. If you
use ip to change the MAC address of a VF while the VF driver is loaded,
closing the VF interface or unloading the VF driver will cause the VF
driver to remove the MAC filter for its original (now invalid) MAC
address.
Jesse cleans up macros which are no longer needed or used.
I (Jeff) cleanup function header comments to ensure Doxygen/kdoc works
correctly to generate documentation without warnings.
Anjali fixes a bug where ethtool set-channels would return failure when
configuring only one Rx queue. Then fixes a bug where the driver was
erroneously exiting the driver unload path if one part of the unload
failed.
Shannon fixes if the IPV6EXADD but is set in the Rx descriptor status,
there was an optional extension header with an alternate IP address
detected and the hardware checksum was not handling the alternate IP
address correctly. Then adjusts the ITR max and min values to match
the hardware max value and recommended min value. Shannon makes sure
to clear the PXE mode after the adminq is initialized.
v2:
- fix patch 14 "i40e: enable PTP" to address Richard Cochran's spelling
catch and Ben Hutchings Kconfig, SIOCGHWTSTAMP and sizeof() suggestions
- added Paul Gortmaker's i40evf fix patch
v3:
- fix patch 14 "i40e: enable PTP" to address Ben Hutchings concerns about
a race with PTP init and cleanup and i40e_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warning, which occurs in casts when
accessing the data in the CAN frames (struct can_frame) in the RX and TX
routines:
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:572:28: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:572:28: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:572:28: got restricted __be32 [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:575:40: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: got restricted __be32 [usertype] <noident>
As the data is indeed big endian, use "__be32" instead of "u32", when casting
it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Building arm:allmodconfig fails with
flexcan.c: In function 'flexcan_read':
flexcan.c:243:2: error: implicit declaration of function 'in_be32'
flexcan.c: In function 'flexcan_write':
flexcan.c:248:2: error: implicit declaration of function 'out_be32'
in_be32 and out_be32 do not (or no longer) exist for ARM targets.
Disable the build for ARM on big endian CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Elcus CAN200PCI card.
Signed-off-by: Oleg Moroz <oleg.moroz@mcc.vniiem.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As of commit 7f12ad741a ("i40evf: transmit
and receive functionality") the s390 builds (allyesconfig) fail with:
drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq':
drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch'
make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1
due to an implicit assumption that the prototype from linux/prefetch.h
will be present.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the ITR max and min values to match the hardware max value
and the recommended min value. These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.
Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the IPV6EXADD bit is set in the Rx descriptor status, there
was an optional extension header with an alternate IP address
detected. The HW checksum offload doesn't handle the alternate
IP address correctly so likely comes up with the wrong answer.
Thus, if the bit is set we ignore the checksum offload value.
Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.
Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.
Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.
Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes make Doxygen/kdoc work correctly without warnings.
Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.
Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.
Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restore the original regulatory testing functionality and also
make it more flexible by allowing the parameters to be specified
when creating a dynamic radio.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new commands to the hwsim generic netlink family to allow
creating and destroying radios on the fly. The number of channels
a radio supports can be specified when it's created, if it isn't
the module parameter will be used as default.
This should be extended in the future to allow other parameters
to be specified, e.g.
* list of channels
* interface combinations, particularly P2P_DEVICE support
* regtest
* and pretty much all other hardware capabilities
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reject wmediumd registrations when any devices have multi-channel
capability, but register the generic netlink family unconditionally
to make it possible to add new commands that shouldn't depend on
the number of (default) channels.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There can't be two wmediumd instances controlling hwsim,
so reject registration from a second one and verify in
the commands that it's the correct instance calling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will make the next patch, adding support for netlink,
smaller and more readable. The code is not modified here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To later allow dynamic registration, assign the index for the
struct device and MAC address from a new free-running counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the flag that the module parameter sets instead, so
later radios can use different parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the radio cleanup into a new function to later
allow deleting a single radio from the list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support dynamic radio registration in the future,
refactor the actual registration into a new function with only
minor cleanups. Since it had to change anyway, also clean up
the init error paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regtest thing worked based on the radio loop, but with
more dynamic radio registration that loop won't really exist
as is. We can add it back later with proper dynamic code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepare the code to support, in theory, different devices
with a different number of channels supported. Right now
this doesn't really change anything, but will allow for
dynamic device registration in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to print a message, and genl_unregister_family()
can't really fail so remove the error message there as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
o Consider number of Tx queues while calculating the length of
Tx statistics as part of ethtool stats.
o Calculate statistics lenght properly for 82xx and 83xx adapter
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not updating TX stats so it was not populating
statistics in `ifconfig` command output.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 fowarding offload will bypass the rx handler of real device. This will make
the packet could not be forwarded to macvtap device. Another problem is the
dev_hard_start_xmit() called for macvtap does not have any synchronization.
Fix this by forbidding L2 forwarding for macvtap.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
For the mac80211 bits, Johannes says:
"I have a fix from Javier for mac80211_hwsim when used with wmediumd
userspace, and a fix from Felix for buffering in AP mode."
For the NFC bits, Samuel says:
"This pull request only contains one fix for a regression introduced with
commit e29a9e2ae1. Without this fix, we can not establish a p2p link
in target mode. Only initiator mode works."
For the iwlwifi bits, Emmanuel says:
"It only includes new device IDs so it's not vital. If you have a pull
request to net.git anyway, I'd happy to have this in."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x triggers warnings with CONFIG_DMA_API_DEBUG=y:
WARNING: CPU: 0 PID: 2253 at lib/dma-debug.c:887 check_unmap+0xf8/0x920()
bnx2x 0000:28:00.0: DMA-API: device driver frees DMA memory with
different size [device address=0x00000000da2b389e] [map size=1490 bytes]
[unmap size=66 bytes]
The reason is that bnx2x splits a TSO BD into two BDs (headers + data)
using one DMA mapping for both, but it uses only the length of the first
BD when unmapping.
This patch fixes the bug by unmapping the whole length of the two BDs.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The recent patch to improve guest receive side flow control (ca2f09f2) had a
slight flaw in the wait condition for the vif thread in that any remaining
skbs in the guest receive side netback internal queue would prevent the
thread from sleeping. An unresponsive frontend can lead to a permanently
non-empty internal queue and thus the thread will spin. In this case the
thread should really sleep until the frontend becomes responsive again.
This patch adds an extra flag to the vif which is set if the shared ring
is full and cleared when skbs are drained into the shared ring. Thus,
if the thread runs, finds the shared ring full and can make no progress the
flag remains set. If the flag remains set then the thread will sleep,
regardless of a non-empty queue, until the next event from the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_sir driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_irda driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 80c33dd "net: add might_sleep() call to napi_disable"
bnx2x fails the might_sleep tests causing a stack trace to appear whenever
the driver is unloaded, as local_bh_disable() is being called before
napi_disable().
This changes the locking schematics related to CONFIG_NET_RX_BUSY_POLL,
preventing the need for calling local_bh_disable() and thus eliminating
the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the bcm43362 1x1 11n chipset. This
chipset is used in AP6210 wifi module found on Cubieboard [1].
[1] http://cubieboard.org/
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nvs file name to module firmware list
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.
Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware requires a full packet template to be pointed to when adding
hardware flow filters. This patch adds the template and uses it for
programming filters.
Change-ID: I09db9f4ab0207ca9c520ae36596d74e1a0663ae5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some badly formatted lines, long lines and a mis-formatted else.
Change-ID: Iac2eef064ae27c55a0c3d9c15c525bf8fed8ab6f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The admin queue can be used to send messages among the physical
function interfaces. This adds the code to handle that case.
Change-ID: I0700fcc47e41433131a381f0eb72fc7b01b6bd87
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since nearly everything we do is synchronous, using the interrupt-on-error bit
is unnecessary and causing unneeded interrupts. If anyone wants to use the bit
they can turn it on in individual AQ requests using the cmd_details parameter.
Change-ID: I4690a9c561d3e0836aeadb4f88f8a8702b1d1366
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call AQ to release any reservation held by this PF on the NVM resource
lock on startup, in order to clear anything that might have been left over from
a previous run. The lock is only cleared by the requestor calling for it to be
cleared, on power-on, or firmware reset. This should help limit the need for
rebooting a customer machine if something goes wrong on a firmware update or
some other action.
Change-ID: I8c8473e601d4ef512dda7baa77a6e75f2e5fea49
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS initialization was doing some extra work, remove the extra
work and any bugs it created when managing number of queues.
Change-ID: Iea75b04a70d73ce76947b6a177ce89ab4899d4c6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware support splitting packets on headers
but with the use of GRO we don't need the extra bus
overhead, so make this driver more like igb and ixgbe and
disable packet split.
Change-ID: Id42f2c3736baa9d5bdfe1f72d64226e7d8ebd737
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The memory barrier used in maybe_stop_tx can use a comment.
Also add checks to VSI->rx_rings to ensure a kernel panic is not induced.
Change-ID: I48cc1bf1d6cf301818155b737edeef77c0d790c7
Change-ID: I1363a8445fbf521a26267849966296ed55f43ad8
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC address format expected by the hardware is in a very specific
format, and the driver was filling in the data incorrectly.
Change-ID: I7bc66505ef459ee347dd3bda68051004c141c689
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do. In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware. This left interrupts disabled
on this queue.
Re-enable the interrupt whenever leaving this function.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning descriptors, we must set up ALL fields, not just the DMA
address. The initial setup does this correctly, but not the cleanup
code, so the firmware would process the ring exactly once and then fail.
Change-ID: I2930b83c76194b3016a8ac0fa693f9a573995640
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The admin queue length register is updated in
config_a<sq|rq>_regs functions. We should not update it again,
as we will trigger firmware to init the AQ again. In this case
firmware will lose the information about the AQ Rx tail position
and will see Rx queue as full (no free desc for FW to use).
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF VSI was never updated to enable or disable internal switch loopback
when VFs were created or destroyed via the sysfs interface. Add some
helper functions to take care of that.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Addresses a few code format issues that have crept in over time.
Change-Id: I1a62cbd16b29a218a933b0f7176abe748f9615e8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework Shadow RAM read word/buffer functions to not use AQ Request
Resource commands. Requesting resource is not needed for SR read
operations which are done through SRCTL register. Access to SR through
register is controlled through DONE bit within SRCTL. With this change
we do not block whole NVM resource for SR read operations.
Change-Id: I73e96cdea39a45ee7b5bdf038e527308de2d9efe
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to check if we are dealing with the correct MAC type before we
try to read anything from the registers.
Change-Id: I3989516999d06c3009e87d6a2eafc20af305c5c2
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move PF ID initialization code from PF reset routine to earlier driver
initialization function. There are a few operations which need the
PF ID before the first PF reset is called.
Change-Id: I7e971f7556b46a837149850ec05ce115c35db575
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a smaller range of test registers in MFP mode as there are fewer
resources than when in SFP mode.
Change-Id: I08424890c3f57b5dde5ee99e99724ce252e0875a
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware's AdminQ interface has matured a little, so update the
code to use the new fields and values.
Change-Id: I8fcd7b443f268dcf9346bd6a9e940fe9c2958891
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RSTAT comes back with DEVICE READY to indicate that the HW is ready,
but we still have to wait for the FW to indicate that the Core and Global
modules are back up again. This needs a read of the NVM_ULD register.
Change-Id: I88276165f9cd446d2f166fb4b8cff00521af4bec
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF is allowed to request the PF to set its already assigned
MAC address without generating an error.
Change-Id: I8dfdf353396995dbbb26cafab4e42b451911da3d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the 8021q driver is loaded it sets VLAN 0 filters on all devices.
This does not mean that any VLAN tagged packet should be accepted.
Instead accept only VLAN 0 tagged packets so that upper layers can
interpret the priority bits.
Change-Id: I17274a540b613749612ffe23a3aef2b8ee6ff6a4
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast promiscuous should only be turned on when general
promiscuous mode is turned on, otherwise VLAN tagged packets out of
the assigned VLAN domain are received.
Add a broadcast MAC filter in order to continue to receive
broadcast traffic on VLANs, MAIN or VMDQ VSI.
Change-Id: I99d8e382a082ee51201228f1226af3b46452ac55
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add more functionality to debugfs to assist development
and testing of AQ commands.
adds:
send aq_cmd
send indirect aq_cmd
Change-Id: I01710cddd33110a6c1e1aabf84cb6e93cda4c42a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mlx4_en includes a PHC driver it must select PTP_1588_CLOCK.
drivers/built-in.o: In function `mlx4_en_get_ts_info':
>> en_ethtool.c:(.text+0x391a11): undefined reference to `ptp_clock_index'
drivers/built-in.o: In function `mlx4_en_remove_timestamp':
>> (.text+0x397913): undefined reference to `ptp_clock_unregister'
drivers/built-in.o: In function `mlx4_en_init_timestamp':
>> (.text+0x397b20): undefined reference to `ptp_clock_register'
Fixes: ad7d4eaed9 ("mlx4_en: Add PTP hardware clock")
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Replace pr_warn_ratelimited() with net_ratelimit() and netdev_warn().
- Adjust the algnment of some messages.
- Remove the peroid.
- Fix some messages don't have terminating newline.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> as reported for linux-next of Dec.20, 2013
> when CONFIG_NEED_DMA_MAP_STATE is not enabled:
>
> drivers/net/ethernet/brocade/bna/bnad.c: In function 'bnad_start_xmit':
> drivers/net/ethernet/brocade/bna/bnad.c:3074:26: error: 'struct bnad_tx_vector' has no member named 'dma_len'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes some typos found by Sergei.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla posted a patch trying to address following problem :
<quote>
The vxlan driver sets itself as the socket owner for all the TX flows
it encapsulates (using vxlan_set_owner()) and assigns it's own skb
destructor. This causes all tunneled traffic to land up on only one TXQ
as all encapsulated skbs refer to the vxlan socket and not the original
socket. Also, the vxlan skb destructor breaks some functionality for
tunneled traffic like wmem accounting and as TCP small queues and
FQ/pacing packet scheduler.
</quote>
I reworked Sathya patch and added some explanations.
vxlan_xmit() can avoid one skb_clone()/dev_kfree_skb() pair
and gain better drop monitor accuracy, by calling kfree_skb() when
appropriate.
The UDP socket used by vxlan to perform encapsulation of xmit packets
do not need to be alive while packets leave vxlan code. Its better
to keep original socket ownership to get proper feedback from qdisc and
NIC layers.
We use skb->sk to
A) control amount of bytes/packets queued on behalf of a socket, but
prior vxlan code did the skb->sk transfert without any limit/control
on vxlan socket sk_sndbuf.
B) security purposes (as selinux) or netfilter uses, and I do not think
anything is prepared to handle vxlan stacked case in this area.
By not changing ownership, vxlan tunnels behave like other tunnels.
As Stephen mentioned, we might do the same change in L2TP.
Reported-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing serial state notification handling expected older Option
devices, having a hardcoded assumption that the Modem port was always
USB interface #2. That isn't true for devices from the past few years.
hso_serial_state_notification is a local cache of a USB Communications
Interface Class SERIAL_STATE notification from the device, and the
USB CDC specification (section 6.3, table 67 "Class-Specific Notifications")
defines wIndex as the USB interface the event applies to. For hso
devices this will always be the Modem port, as the Modem port is the
only port which is set up to receive them by the driver.
So instead of always expecting USB interface #2, instead validate the
notification with the actual USB interface number of the Modem port.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returns 0 in case of success, !0 error otherwise. Fix the improper error
verification.
Fixes: 2c9839c143 ("bonding: add num_grat_arp attribute netlink support")
CC: sfeldma@cumulusnetworks.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
