IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
parse_hid_report_descriptor() has a while (i < length) loop, which
only guarantees that there's at least 1 byte in the buffer, but the
loop body can read multiple bytes which causes out-of-bounds access.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.
To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.
This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.
Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Support was added based on Goodix GitHub repo [1]. There are two major
differences between gt1151 and currently supported devices (gt9x):
* CONFIG_DATA register has 0x8050 address instead of 0x8047,
* config data checksum has 16-bit width instead of 8-bit.
Also update goodix_i2c_test() function, so it reads ID register (which
has the same address for all devices) instead of CONFIG_DATA (because
its address is known only after reading ID of the device).
[1] https://github.com/goodix/gt1x_driver_generic
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ELAN0611 touchpad uses elan_i2c as its driver. It can be found
on Lenovo ideapad 320-15IKB.
So add it to ACPI table to enable the touchpad.
[Ido Adiv <idoad123@gmail.com> reports that the same ACPI ID is used for
Elan touchpad in ideapad 520].
BugLink: https://bugs.launchpad.net/bugs/1723736
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We've been missing a goto to the unwind path...
Acked-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is nothing in the uinput kernel header that is of use to anyone in
the kernel besides the uinput driver itself, so let's fold it into the
driver code (leaving uapi part intact).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need for this wrapper; let's use input_allocate_device()
directly, and complete initialization in uinput_create_device().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously uinput force feedback requests waited for the userspace
indefinitely, which caused users to block when uinput server process
become unresponsive. Let's establish a 30 seconds deadline for servicing
upload and erase force feedback effect actions, so that users have a
chance to abort stuck requests.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Stephen Lu <lumotuwe@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Stephen Lu <lumotuwe@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ7clWAAoJEHm+PkMAQRiG07AH/iKcej+AsurISHx6i/LUEDC1
a9wo5HAR5kEj+ohdE3JSkD9BHLcyhcCXaqIk9yOrwi9xv1DrPv8U/nGkKzZJzFi2
mGWK09Zgi+vgSpA+YSErgl05IVGtgaryQQPqQdawpyRpqTUwP0+2pLnKEnJe0f05
fpv+S4bDKUCuE8GcVNjF9gxXDg8j60fFa+oAcn7QPS6dCun/H6TbDRue5oeky0Y+
50ZYjjioy9S9DIm2VF7pktMCP/mK/fgb+Q+4Up09VJGHGhq+891SRJ27yDulxo47
/gq22SRIGBX2PGNllSwhYslgaCRRlYTMBYOIWrBreanA4NpGD662dp+GgWhD154=
=TAMw
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc6' into next
Merge with mainline to bring in the timer API changes.
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the EDT M12 series of touchscreens.
Signed-off-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the driver also is useful for some non-EDT touchscreens based on
the focaltec chips introduce the concept of a "generic" focaltec based
touch.
Use a better heuristics for model detection and be more specific in the
source.
Signed-off-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the GPIO mouse probe nicely from the device tree if found in a
tree. As the driver uses device properties it can easily be amended to also
probe from ACPI devices.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This converts the GPIO mouse to use descriptors and fwnode properties. The
polarity settings go out the window since GPIO descriptor already know
about polarity so this should be configured in device tree or ACPI or
similar.
Set scanning interval by default to 50ms if not found as a property on the
device.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use more appropriate names for the "platform data" which is now just a
simple state container for the GPIO mouse.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is not used much: git grep gpio_mouse_platform_data shows
that absolutely nothing in the kernel defines this platform
data.
It could be argued that the driver should be deleted. But that
is a bit harsh I think since it seems generally useful. So
this patch starts a series which repurposes it to be used with
hardware nodes from device tree or ACPI.
This first patch simply localize the platform data header and
allocates a dummy platform data.
Yes: this patch leaves the driver in a pretty useless state,
but since nothing is instantiating this driver, it doesn't
make it more useless than it already is. Later patches makes
use of the driver.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce a device table used for blacklisting devices. We currently
blacklist the motion sensor subdevice of THQ Udraw and Sony ds3/ds4.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
[dtor: siwtched to blacklist built on input_device_id and using
input_match_device_id()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.
This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.
Fixes: c3cc94470bd3 ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, enabling keypad interrupts is one of the first operations
done on the keypad, even before the interrupt is requested, so there is
a small time window where the keypad can fire interrupts but the driver
is not yet ready to handle them. It's fine for level interrupts because
they will be handled anyway, but not so much for edge ones.
This commit modifies and moves the function in charge of configuring the
keypad. Enabling interrupts is now the last thing done on the keypad,
and after the interrupt has been requested by the driver.
Writing to the config register was also used to determine if the device
was indeed present on the bus or not, this has been replaced by reading
the lock/event count register to keep the same functionality.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit 78bcac7b2ae1e ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.
But, commit 78bcac7b2ae1e didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.
Fixes: 78bcac7b2ae1e ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:
- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;
while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.
Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The array rmi_f54_report_type_names is local to the source and does
not need to be in global scope, so make it static. Also make the array
const char * const.
Cleans up sparse warning:
symbol 'rmi_f54_report_type_names' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In certain situations kernel tracking seems to be getting confused
and incorrectly reporting the slot of a contact. On example is when
the user does a three finger click or tap and then places two fingers
on the touchpad in the same area. The kernel tracking code seems to
continue to think that there are three contacts on the touchpad and
incorrectly alternates the slot of one of the contacts. The result that
is the input subsystem reports a stream of button press and release
events as the reported slot changes.
Kernel tracking was originally enabled to prevent cursor jumps, but it
is unclear how much of an issue kernel jumps actually are. This patch
simply disabled kernel tracking for now.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1482640
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Kamil Páral <kparal@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
relative sysfs_remove_group and goto label.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
relative sysfs_remove_group.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On x86 we historically used falling edge interrupts in the driver
because that's how first Chrome devices were configured. They also
did not use ACPI to enumerate I2C devices (because back then there
was no kernel support for that), so trigger was hard-coded in the
driver. However the controller behavior is much more reliable if
we use level triggers, and that is how we configured ARM devices,
and how want to configure newer x86 devices as well. All newer
x86 boxes have their I2C devices enumerated in ACPI.
Let's see if platform code (ACPI, DT) described interrupt and
specified particular trigger type, and if so, let's use it instead
of always clobbering trigger with IRQF_TRIGGER_FALLING. We will
still use this trigger type as a fallback if platform code left
interrupt trigger unconfigured.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196761
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change control of TOUCHSCREEN_USB_EASYTOUCH prompt string from
EMBEDDED to EXPERT to match the rest of this Kconfig file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
