IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The ao_clk81 in AO domain have two clock source,
one from a 32K alt crystal we name it as ao_alt_clk,
another is the clk81 signal from EE domain.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the GPIO interrupt controller driver which found in the Amlogic's
Meson-AXG SoC, the controller share the similar ASIC IP as other meson SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The IP of eMMC controller in AXG is similiar to Meson-GX series.
Here we add the initial support of the HS200 mode with
clock running at 166MHz (to be safe), since we found some eMMC chip
fail to run at 200MHz due to tunning phase error.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: drop incorrect SDIO pwrseq property]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are a few differences between the gxbb and gxl clock controllers
which makes them incompatible. The hdmi, gp0 and fixed pll are
different. The rate of these plls reported by gxbb driver on a gxl
device would be wrong.
Remove the gxbb compatible from the gxl clock controller node so only
the correct driver is matched.
Fixes: 973fbd55b53c ("ARM64: dts: meson-gxl: Add clock nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Like the meson-gx, the axg clock controller should go through a syscon
to access the hhi register region, and not directly map the region.
This way, the hhi register region can be used safely by multiple drivers.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The parent of the meson-gx clock controller should be the hhi system
controller, not the HIU bus. This way, the HHI register region can be
used safely by multiple drivers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM2 board connects the dwc3 controller to an internal 4-port
USB hub which. Two of these ports are accessible directly soldered to
the board, while the other two are accessible through the 40-pin "GPIO"
header.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Nexbox A95X provides two USB ports. Enable the SoC's USB controller
on this board to make these USB ports usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The LibreTech CC ("Le Potato") board provides four USB connectors.
These are provided by a hub which is connected to the SoC's USB
controller.
Enable the SoC's USB controller to make the USB ports usable. Also turn
on the HDMI_5V regulator when powering on the PHY because (even though
it's not shown in the schematics) HDMI_5V also supplies the USB VBUS.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All S905D (GXL) and S912 (GXM) reference boards (namely these are
P230, P231, Q200 and Q201) provide USB connectors.
This enables the USB controller on these boards to make the USB ports
actually usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All boards based on the P212 reference design (the P212 reference board
itself and the Khadas VIM) have USB connectors (in case of the Khadas
VIM the first port is exposed through the USB Type-C connector, the
second port is connected to a 4-port USB hub).
This enables the USB controller on these boards to make the USB ports
actually usable.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The USB configuration on GXM is slightly different than on GXL. The dwc3
controller's internal hub has three USB2 ports (instead of 2 on GXL)
along with a dedicated USB2 PHY for this port. However, it seems that
there are no pins on GXM which would allow connecting the third port to
a physical USB port.
Passing the third PHY is required though, because without it none of the
other USB ports is working (this seems to be a limitation of how the
internal USB hub works, if one PHY is disabled then no USB port works).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds USB host support to the Meson GXL SoC. A dwc3 controller is
used for host-mode, while a dwc2 controller (not added in this patch
because I could not get it working) is used for device-mode only.
The dwc3 controller's internal roothub has two USB2 ports enabled but no
USB3 port. Each of the ports is supplied by a separate PHY. The USB pins
are connected to the SoC's USBHOST_A and USBOTG_B pins.
Due to the way the roothub works internally the USB PHYs are left
enabled. When the dwc3 controller is disabled the PHY is never powered on
so it does not draw any extra power. However, when the dwc3 host
controller is enabled then all PHYs also have to be enabled, otherwise
USB devices will not be detected (regardless of whether they are plugged
into an enabled port or not). This means that only the dwc3 controller
has to be enabled on boards with USB support (instead of requiring all
boards to enable the PHYs additionally with the chance of forgetting to
enable one and breaking all other ports with that as well).
This also adds the USB3 PHY which currently only does some basic
initialization. That however is required because without it high-speed
devices (like USB thumb drives) do not work on some devices (probably
because the bootloader does not configure the USB3 PHY registers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.
Remove the unused properties from the gpio-fan node.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Mali-450 IP can run up to 744MHz, bump the frequency using
the GP0 PLL clock.
Cc: Michal Lazo <michal.lazo@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds a specific wetek dtsi to handle the specific Hub and Play2
boards by no more depending on the p20x dtsi.
This simplifies the hub and play2 dts and will avoid breaking these
boards when adding p200 and p201 specific changes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
Fixes: d341ca88eead ("mmc: meson-gx: rework tuning function")
Suggested-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The compatible in pwm_AO_cd is wrong and does not match anything.
Correct this with the correct compatible string
Fixes: 4a81e5ddfb43 ("ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
add the secure AO system controller with chipid enabled
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the adequate configuration settings, u-boot will loop through the
list of aliases looking for "ethernetX".
By adding an ethernet alias, u-boot can fixup the local-mac-address
property in the kernel's device tree using a value held in its
environment variable ethaddr.
Tested-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The UART_A is connected to a BT module on the S400 board.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Explictly request the pinctrl info for the UART_AO_A controller,
otherwise we may need to rely on bootloader for the initialization.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Describe the pinctrl info for the UART controller which is found
in the Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: s/uart_ao_b_gpioz/uart_ao_b_z/ ]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When update the clock info for the UART controller in the EE domain,
the driver explicitly require 'pclk' in order to work properly.
With current logic of the code, the driver will go for the legacy clock probe
routine if it find current compatible string match to 'amlogic,meson-uart',
which result in not requesting the 'pclk' clock, thus break the driver in the end.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Comparing to RGMII interface, the RMII interface require few pins.
So it's worth describing them here.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In the S400 board, The I2C master-1 is connecting to
the audio speaker daughter board.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Describe all the pin mux for the I2C controller which found in
Meson-AXG SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are four I2C masters in EE domain, and one I2C Master in
AO domain, the DT info here should describe them all.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The address space range is actually 0x18, fixed here.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
-----BEGIN PGP SIGNATURE-----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=lk2H
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Another round of 64-bit DT changes for the new Amlogic SoCs. These
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-axg: enable ethernet for A113D S400 board
ARM64: dts: meson-axg: add ethernet mac controller
ARM64: dts: meson-axg: add the SPICC controller
ARM64: dts: meson-axg: enable IR controller
arm64: dts: meson-axg: switch uart_ao clock to CLK81
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
Signed-off-by: Olof Johansson <olof@lixom.net>
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- clock, pinctrl, PWM and reset nodes for new AXG SoC family
-----BEGIN PGP SIGNATURE-----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=4k+i
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman:
This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG
family of Amlogic SoCs.
* tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add new reset DT node
ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC
ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC
documentation: Add compatibles for Amlogic Meson AXG pin controllers
arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=0wR5
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16" from Kevin Hilman
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm: fix q200 interrupt number
ARM64: dts: meson-gxm: add the PHY interrupt line on Khadas VIM2
ARM64: dts: meson: add comments with the GPIO for the PHY interrupts
ARM64: dts: amlogic: use generic bus node names
ARM64: dts: meson: drop "sana" clock from SAR ADC
ARM64: dts: odroid-c2: Add HDMI and CEC Nodes
ARM64: dts: meson-gx: grow reset controller memory zone
ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards
ARM64: dts: meson-gx: add VPU power domain
Add PWM DT info for the Amlogic's Meson-Axg SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: dropped unnecessary include]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Try to add Hiubus DT info, and also enable clock DT info
for the Amlogic's Meson-AXG SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Correct the interrupt number assigned to the Realtek PHY in the q200
Fixes: b94d22d94ad2 ("ARM64: dts: meson-gx: add external PHY interrupt on some platforms")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The INTB/PMEB pin of the RTL8211F PHY on the Khadas VIM2 is routed to
GPIOZ_15. Add the corresponding interrupt using the GPIO interrupt
controller so the PHY framework doesn't have to poll the PHY for it's
status.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
