IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Some function prototypes and body for Thermal Assist Units were not in
sync. Update the function definition to match the existing function
declaration found in `setup-common.c`, changing an `int` return type to a
`u32` return type. Move the prototypes to a header file. Fix the following
warnings, treated as error with W=1:
arch/powerpc/kernel/tau_6xx.c:257:5: error: no previous prototype for ‘cpu_temp_both’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:262:5: error: no previous prototype for ‘cpu_temp’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:267:5: error: no previous prototype for ‘tau_interrupts’ [-Werror=missing-prototypes]
Compile tested with CONFIG_TAU_INT.
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add one missing prototype for function rh_dump_blk. Fix warning treated as
error in W=1:
arch/powerpc/lib/rheap.c:740:6: error: no previous prototype for ‘rh_dump_blk’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function prototypes were declared within a `#ifdef CONFIG_PPC_LITE5200`
block which would prevent them from being visible when compiling
`mpc52xx_pm.c`. Move the prototypes outside of the `#ifdef` block to fix
the following warnings treated as errors with W=1:
arch/powerpc/platforms/52xx/mpc52xx_pm.c:58:5: error: no previous prototype for ‘mpc52xx_pm_prepare’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:113:5: error: no previous prototype for ‘mpc52xx_pm_enter’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:181:6: error: no previous prototype for ‘mpc52xx_pm_finish’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a missing prototype for function `note_bootable_part` to silence a
warning treated as error with W=1:
arch/powerpc/platforms/powermac/setup.c:361:12: error: no previous prototype for ‘note_bootable_part’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pmac_pfunc_base_install prototype was declared in powermac/smp.c since
function was used there, move it to pmac_pfunc.h header to be visible in
pfunc_base.c. Fix a warning treated as error with W=1:
arch/powerpc/platforms/powermac/pfunc_base.c:330:12: error: no previous prototype for ‘pmac_pfunc_base_install’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/pci.c:34:5: error: no previous prototype for ‘gg2_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:61:5: error: no previous prototype for ‘gg2_write_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:97:5: error: no previous prototype for ‘rtas_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:112:5: error: no previous prototype for ‘rtas_write_config’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the value of x is never intended to be read, declare it with gcc
attribute as unused. Fix warning treated as error with W=1:
arch/powerpc/platforms/powermac/bootx_init.c:471:21: error: variable ‘x’ set but not used [-Werror=unused-but-set-variable]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove variable declaration idu_size and associated code since not used.
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/setup.c:97:6: error: no previous prototype for ‘chrp_show_cpuinfo’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:302:13: error: no previous prototype for ‘chrp_setup_arch’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:385:16: error: variable ‘idu_size’ set but not used [-Werror=unused-but-set-variable]
arch/powerpc/platforms/chrp/setup.c:526:13: error: no previous prototype for ‘chrp_init_IRQ’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:559:1: error: no previous prototype for ‘chrp_init2’ [-Werror=missing-prototypes]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function hlwd_pic_init can be made static, so do it. Fix the following
warning treated as error (W=1):
../arch/powerpc/platforms/embedded6xx/hlwd-pic.c:158:20: error: no previous prototype for ‘hlwd_pic_init’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 7a22d6321c ("powerpc/mm/radix: Update command line parsing for
disable_radix") an `if` statement was added for a possible empty body
(prom_debug).
Fix the following warning, treated as error with W=1:
arch/powerpc/kernel/prom_init.c:656:46: error: suggest braces around empty body in an ‘if’ statement [-Werror=empty-body]
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trivial fix to remove the following sparse warnings:
arch/powerpc/kernel/module_32.c:112:74: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/module_32.c:117:74: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1155:28: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1230:20: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1385:36: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1752:23: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2084:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2110:32: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2167:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2183:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:277:20: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:155:67: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:247:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:249:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:252:37: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:127:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:148:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:44:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:57:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:87:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:160:31: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:167:22: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:274:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:285:31: warning: Using plain integer as NULL pointer
arch/powerpc/include/asm/hugetlb.h:204:16: warning: Using plain integer as NULL pointer
arch/powerpc/mm/ppc_mmu_32.c:170:21: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:1227:23: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:65:24: warning: Using plain integer as NULL pointer
Also use `--fix` command line option from `script/checkpatch --strict` to
remove the following:
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#72: FILE: arch/powerpc/kernel/btext.c:160:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "!vbase"
#80: FILE: arch/powerpc/kernel/btext.c:167:
+ if (vbase == NULL)
CHECK: Comparison to NULL could be written "!base"
#89: FILE: arch/powerpc/kernel/btext.c:274:
+ if (base == NULL)
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#98: FILE: arch/powerpc/kernel/btext.c:285:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "strstr"
#117: FILE: arch/powerpc/kernel/module_32.c:117:
+ if (strstr(secstrings + sechdrs[i].sh_name, ".debug") != NULL)
CHECK: Comparison to NULL could be written "!Hash"
#130: FILE: arch/powerpc/mm/ppc_mmu_32.c:170:
+ if (Hash == NULL)
CHECK: Comparison to NULL could be written "Hash"
#143: FILE: arch/powerpc/mm/tlb_hash32.c:44:
+ if (Hash != NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#152: FILE: arch/powerpc/mm/tlb_hash32.c:57:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#161: FILE: arch/powerpc/mm/tlb_hash32.c:87:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#170: FILE: arch/powerpc/mm/tlb_hash32.c:127:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#179: FILE: arch/powerpc/mm/tlb_hash32.c:148:
+ if (Hash == NULL) {
ERROR: space required after that ';' (ctx:VxV)
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "node"
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "!region"
#201: FILE: arch/powerpc/platforms/powermac/pci.c:1227:
+ if (region == NULL)
CHECK: Comparison to NULL could be written "of_get_property"
#214: FILE: arch/powerpc/platforms/powermac/setup.c:155:
+ if (of_get_property(np, "cache-unified", NULL) != NULL && dc) {
CHECK: Comparison to NULL could be written "!np"
#223: FILE: arch/powerpc/platforms/powermac/setup.c:247:
+ if (np == NULL)
CHECK: Comparison to NULL could be written "np"
#226: FILE: arch/powerpc/platforms/powermac/setup.c:249:
+ if (np != NULL) {
CHECK: Comparison to NULL could be written "l2cr"
#230: FILE: arch/powerpc/platforms/powermac/setup.c:252:
+ if (l2cr != NULL) {
CHECK: Comparison to NULL could be written "via"
#243: FILE: drivers/macintosh/via-pmu.c:277:
+ if (via != NULL)
CHECK: Comparison to NULL could be written "current_req"
#252: FILE: drivers/macintosh/via-pmu.c:1155:
+ if (current_req != NULL) {
CHECK: Comparison to NULL could be written "!req"
#261: FILE: drivers/macintosh/via-pmu.c:1230:
+ if (req == NULL || pmu_state != idle
CHECK: Comparison to NULL could be written "!req"
#270: FILE: drivers/macintosh/via-pmu.c:1385:
+ if (req == NULL) {
CHECK: Comparison to NULL could be written "!pp"
#288: FILE: drivers/macintosh/via-pmu.c:2084:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#297: FILE: drivers/macintosh/via-pmu.c:2110:
+ if (count < 1 || pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#306: FILE: drivers/macintosh/via-pmu.c:2167:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "pp"
#315: FILE: drivers/macintosh/via-pmu.c:2183:
+ if (pp != NULL) {
Link: https://github.com/linuxppc/linux/issues/37
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some functions prototypes were missing for the non-altivec code. Add the
missing prototypes in a new header file, fix warnings treated as errors
with W=1:
arch/powerpc/lib/xor_vmx_glue.c:18:6: error: no previous prototype for ‘xor_altivec_2’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:29:6: error: no previous prototype for ‘xor_altivec_3’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:40:6: error: no previous prototype for ‘xor_altivec_4’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:52:6: error: no previous prototype for ‘xor_altivec_5’ [-Werror=missing-prototypes]
The prototypes were already present in <asm/xor.h> but this header file is
meant to be included after <include/linux/raid/xor.h>. Trying to re-use
<asm/xor.h> directly would lead to warnings such as:
arch/powerpc/include/asm/xor.h:39:15: error: variable ‘xor_block_altivec’ has initializer but incomplete type
Trying to re-use <asm/xor.h> after <include/linux/raid/xor.h> in
xor_vmx_glue.c would in turn trigger the following warnings:
include/asm-generic/xor.h:688:34: error: ‘xor_block_32regs’ defined but not used [-Werror=unused-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The set of paca fields we dump in xmon has gotten somewhat out of
date. Update to add some recently added fields.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We've added some fields with longer names since we originally wrote
this, so the fields are no longer lined up. Adjust the widths to make
it all look nice again, eg:
0:mon> dp
paca for cpu 0x0 @ c000000001fa0000:
possible = yes
...
slb_shadow [0] = 0xc000000008000000 0x400ea1b217000500
slb_shadow [1] = 0xd000000008000001 0x400d43642f000510
...
rfi_flush_fallback_area = c0000000fff80000 (0xcc8)
...
accounting.starttime_user = 0x51582f07 (0xae8)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows the compiler to verify the format strings vs the types of
the arguments.
Update the other prototype declarations in asm/xmon.h.
Silence warnings (triggered at W=1) by adding relevant __printf
attribute. Move #define at bottom of the file to prevent conflict with
gcc attribute.
Solves the original warning:
arch/powerpc/xmon/nonstdio.c:178:2: error: function might be
possible candidate for ‘gnu_printf’ format attribute
In turn this uncovered many formatting errors in xmon.c, all fixed in
this patch.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Always use px not p, fixup the 44x specific code, tweak change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In dump_one_paca() the DUMP macro unconditionally prepends '#' to the
printf format specifier. In most cases we're using either 'x' or 'lx'
etc. and that is OK. But for 'p' and other formats using '#' is
actually undefined, and once we enable printf() checking for
xmon_printf() we will get warnings from the compiler.
So just have each usage specify the full format, that way we can omit
'#' when it's inappropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
When single-stepping kernel code from xmon without a debug hook
enabled the kernel crashes. This can happen when kernel starts with
xmon on crash disabled but xmon is entered using sysrq.
Call force_enable_xmon when single-stepping in xmon to install the
xmon debug hooks.
Fixes: e1368d0c9e ("powerpc/xmon: Setup debugger hooks when first break-point is set")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
New binutils generate the following warning
AS arch/powerpc/kernel/head_8xx.o
arch/powerpc/kernel/head_8xx.S: Assembler messages:
arch/powerpc/kernel/head_8xx.S:916: Warning: invalid register expression
This patch fixes it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit a7a9dcd882 ("powerpc: Avoid taking a data miss on every
userspace instruction miss") has shown that limiting the read of
faulting instruction to likely cases improves performance.
This patch goes further into this direction by limiting the read
of the faulting instruction to the only cases where it is likely
needed.
On an MPC885, with the same benchmark app as in the commit referred
above, we see a reduction of about 3900 dTLB misses (approx 3%):
Before the patch:
Performance counter stats for './fault 500' (10 runs):
683033312 cpu-cycles ( +- 0.03% )
134538 dTLB-load-misses ( +- 0.03% )
46099 iTLB-load-misses ( +- 0.02% )
19681 faults ( +- 0.02% )
5.389747878 seconds time elapsed ( +- 0.06% )
With the patch:
Performance counter stats for './fault 500' (10 runs):
682112862 cpu-cycles ( +- 0.03% )
130619 dTLB-load-misses ( +- 0.03% )
46073 iTLB-load-misses ( +- 0.05% )
19681 faults ( +- 0.01% )
5.381342641 seconds time elapsed ( +- 0.07% )
The proper work of the huge stack expansion was tested with the
following app:
int main(int argc, char **argv)
{
char buf[1024 * 1025];
sprintf(buf, "Hello world !\n");
printf(buf);
exit(0);
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add include of pagemap.h to fix build errors]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use symbolic names defined in asm/ppc-opcode.h
instead of hardcoded values.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch exports tm_enable()/tm_disable/tm_abort() APIs, which
will be used for PR KVM transactional memory logic.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patches add some macros for CR0/TEXASR bits so that PR KVM TM
logic (tbegin./treclaim./tabort.) can make use of them later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PR KVM will need to reuse msr_check_and_set().
This patch exports this API for reuse.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support to read 64-bit sensor values. This method is
used to read energy sensors and counters which are of type u64.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e2a800beac ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beac ("powerpc/hw_brk: Fix off by one error when validating DAWR region end")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back when we first introduced the DAWR, in commit 4ae7ebe952
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe952 ("powerpc: Change hardware breakpoint to allow longer ranges")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows us to squash some sparse warnings and also avoids having
to do explicity endian conversions in the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
This allows us to squash some sparse warnings and also avoids having
to do explicity endian conversions in the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Add byte-swapping versions of __raw_writeq() and __raw_rm_writeq().
This allows us to avoid sparse warnings caused by passing __be64 to
__raw_writeq(), which takes unsigned long:
arch/powerpc/platforms/powernv/pci-ioda.c:1981:38:
warning: incorrect type in argument 1 (different base types)
expected unsigned long [unsigned] v
got restricted __be64 [usertype] <noident>
It's also generally preferable to use a byte-swapping accessor rather
than doing it by hand in the code, which is more bug prone.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Currently memory is allocated for core-imc based on cpu_present_mask,
which has bit 'cpu' set iff cpu is populated. We use (cpu number / threads
per core) as the array index to access the memory.
Under some circumstances firmware marks a CPU as GUARDed CPU and boot the
system, until cleared of errors, these CPU's are unavailable for all
subsequent boots. GUARDed CPUs are possible but not present from linux
view, so it blows a hole when we assume the max length of our allocation
is driven by our max present cpus, where as one of the cpus might be online
and be beyond the max present cpus, due to the hole.
So (cpu number / threads per core) value bounds the array index and leads
to memory overflow.
Call trace observed during a guard test:
Faulting instruction address: 0xc000000000149f1c
cpu 0x69: Vector: 380 (Data Access Out of Range) at [c000003fea303420]
pc:c000000000149f1c: prefetch_freepointer+0x14/0x30
lr:c00000000014e0f8: __kmalloc+0x1a8/0x1ac
sp:c000003fea3036a0
msr:9000000000009033
dar:c9c54b2c91dbf6b7
current = 0xc000003fea2c0000
paca = 0xc00000000fddd880 softe: 3 irq_happened: 0x01
pid = 1, comm = swapper/104
Linux version 4.16.7-openpower1 (smc@smc-desktop) (gcc version 6.4.0
(Buildroot 2018.02.1-00006-ga8d1126)) #2 SMP Fri May 4 16:44:54 PDT 2018
enter ? for help
call trace:
__kmalloc+0x1a8/0x1ac
(unreliable)
init_imc_pmu+0x7f4/0xbf0
opal_imc_counters_probe+0x3fc/0x43c
platform_drv_probe+0x48/0x80
driver_probe_device+0x22c/0x308
__driver_attach+0xa0/0xd8
bus_for_each_dev+0x88/0xb4
driver_attach+0x2c/0x40
bus_add_driver+0x1e8/0x228
driver_register+0xd0/0x114
__platform_driver_register+0x50/0x64
opal_imc_driver_init+0x24/0x38
do_one_initcall+0x150/0x15c
kernel_init_freeable+0x250/0x254
kernel_init+0x1c/0x150
ret_from_kernel_thread+0x5c/0xc8
Allocating memory for core-imc based on cpu_possible_mask, which has
bit 'cpu' set iff cpu is populatable, will fix this issue.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Fixes: 39a846db1d ("powerpc/perf: Add core IMC PMU support")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trivial fix to spelling mistake in battery_charging array.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.
We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
My powerpc-linux-gnu-gcc v4.4.5 compiler can't build a 32-bit kernel
any more:
arch/powerpc/lib/sstep.c: In function 'do_popcnt':
arch/powerpc/lib/sstep.c:1068: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1070: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1079: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c: In function 'do_prty':
arch/powerpc/lib/sstep.c:1117: error: integer constant is too large for 'long' type
This file gets compiled with -std=gnu89 which means a constant can be
given the type 'long' even if it won't fit. Fix the errors with a 'ULL'
suffix on the relevant constants.
Fixes: 2c979c489f ("powerpc/lib/sstep: Add prty instruction emulation")
Fixes: dcbd19b48d ("powerpc/lib/sstep: Add popcnt instruction emulation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.
Fixes: 3b8070335f ("powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops")
Cc: stable@vger.kernel.org # v3.2
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A kernel crash in process context that calls emergency_restart from
panic will end up calling opal_event_shutdown with interrupts disabled
but not in interrupt. This causes a sleeping function to be called
which gives the following warning with sysrq+c:
Rebooting in 10 seconds..
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
in_atomic(): 0, irqs_disabled(): 1, pid: 7669, name: bash
CPU: 20 PID: 7669 Comm: bash Tainted: G D W 4.17.0-rc5+ #3
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
___might_sleep+0x174/0x1a0
mutex_lock+0x38/0xb0
__free_irq+0x68/0x460
free_irq+0x70/0xc0
opal_event_shutdown+0xb4/0xf0
opal_shutdown+0x24/0xa0
pnv_shutdown+0x28/0x40
machine_shutdown+0x44/0x60
machine_restart+0x28/0x80
emergency_restart+0x30/0x50
panic+0x2a0/0x328
oops_end+0x1ec/0x1f0
bad_page_fault+0xe8/0x154
handle_page_fault+0x34/0x38
--- interrupt: 300 at sysrq_handle_crash+0x44/0x60
LR = __handle_sysrq+0xfc/0x260
flag_spec.62335+0x12b844/0x1e8db4 (unreliable)
__handle_sysrq+0xfc/0x260
write_sysrq_trigger+0xa8/0xb0
proc_reg_write+0xac/0x110
__vfs_write+0x6c/0x240
vfs_write+0xd0/0x240
ksys_write+0x6c/0x110
Fixes: 9f0fd0499d ("powerpc/powernv: Add a virtual irqchip for opal events")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/Makefile activates -mmultiple on BE PPC32 configs
in order to use multiple word instructions in functions entry/exit.
The patch does the same for the asm parts, for consistency.
On processors like the 8xx on which insn fetching is pretty slow,
this speeds up registers save/restore.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: PPC32 is BE only, so drop the endian checks]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Doing the test at exit of the function avoids an unnecessary
test and branch inside longjmp().
Semantics are unchanged.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 6ad966d730.
That commit was pointless, because csum_add() sums two 32 bits
values, so the sum is 0x1fffffffe at the maximum.
And then when adding upper part (1) and lower part (0xfffffffe),
the result is 0xffffffff which doesn't carry.
Any lower value will not carry either.
And behind the fact that this commit is useless, it also kills the
whole purpose of having an arch specific inline csum_add()
because the resulting code gets even worse than what is obtained
with the generic implementation of csum_add()
0000000000000240 <.csum_add>:
240: 38 00 ff ff li r0,-1
244: 7c 84 1a 14 add r4,r4,r3
248: 78 00 00 20 clrldi r0,r0,32
24c: 78 89 00 22 rldicl r9,r4,32,32
250: 7c 80 00 38 and r0,r4,r0
254: 7c 09 02 14 add r0,r9,r0
258: 78 09 00 22 rldicl r9,r0,32,32
25c: 7c 00 4a 14 add r0,r0,r9
260: 78 03 00 20 clrldi r3,r0,32
264: 4e 80 00 20 blr
In comparison, the generic implementation of csum_add() gives:
0000000000000290 <.csum_add>:
290: 7c 63 22 14 add r3,r3,r4
294: 7f 83 20 40 cmplw cr7,r3,r4
298: 7c 10 10 26 mfocrf r0,1
29c: 54 00 ef fe rlwinm r0,r0,29,31,31
2a0: 7c 60 1a 14 add r3,r0,r3
2a4: 78 63 00 20 clrldi r3,r3,32
2a8: 4e 80 00 20 blr
And the reverted implementation for PPC64 gives:
0000000000000240 <.csum_add>:
240: 7c 84 1a 14 add r4,r4,r3
244: 78 80 00 22 rldicl r0,r4,32,32
248: 7c 80 22 14 add r4,r0,r4
24c: 78 83 00 20 clrldi r3,r4,32
250: 4e 80 00 20 blr
Fixes: 6ad966d730 ("powerpc/64: Fix checksum folding in csum_add()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PMD_PAGE_SIZE() is nowhere used and _PMD_SIZE is only
used by PMD_PAGE_SIZE().
This patch removes them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Directly use fault_in_pages_readable instead of manual __get_user code. Fix
warning treated as error with W=1:
arch/powerpc/kernel/kvm.c:675:6: error: variable ‘tmp’ set but not used [-Werror=unused-but-set-variable]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement a local TLB flush for invalidating an LPID with variants for
process or partition scope. And a global TLB flush for invalidating
a partition scoped page of an LPID.
These will be used by KVM in subsequent patches.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The interrupt controller inside the Wii's Hollywood chip is connected to
two masters, the "Broadway" PowerPC and the "Starlet" ARM926, each with
their own interrupt status and mask registers.
When booting the Wii with mini[1], interrupts from the SD card
controller (IRQ 7) are handled by the ARM, because mini provides SD
access over IPC. Linux however can't currently use or disable this IPC
service, so both sides try to handle IRQ 7 without coordination.
Let's instead make sure that all interrupts that are unmasked on the PPC
side are masked on the ARM side; this will also make sure that Linux can
properly talk to the SD card controller (and potentially other devices).
If access to a device through IPC is desired in the future, interrupts
from that device should not be handled by Linux directly.
[1]: https://github.com/lewurm/mini
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On the Wii, there is a secondary IRQ controller (hlwd-pic), so
flipper-pic's match operation should not be hardcoded to return 1.
In fact, the default matching logic is sufficient, and we can completely
omit flipper_pic_match.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of encoding shift in the table address, use an enumerated index value.
This allow us to do different things in the callback for pte and pmd.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
4K config use one full page at level 4 of the pagetable. Add support for single
fragment allocation in pagetable fragment code and and use that for 4K config.
This makes both 4k and 64k use the same code path. Later we will switch pmd to
use the page table fragment code. This is done only for 64bit platforms which
is using page table fragment support.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have removed 64K page size support, the RCU page table free can
be much simpler for nohash. Make a copy of the the rcu callback to pgalloc.h
header similar to nohash 32. We could possibly merge 32 and 64 bit there. But
that is for a later patch
We also move the book3s specific handler to pgtable_book3s64.c. This will be
updated in a later patch to handle split pmd ptlock.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have in Kconfig
config PPC_64K_PAGES
bool "64k page size"
depends on !PPC_FSL_BOOK3E && (44x || PPC_BOOK3S_64 || PPC_BOOK3E_64)
select HAVE_ARCH_SOFT_DIRTY if PPC_BOOK3S_64
Only supported BOOK3E 64 bit platforms is FSL_BOOK3E. Remove the dead 64k page
support code from 64bit nohash.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We rename the alloc and get_from_cache to indicate they operate on pte
fragments. In later patch we will add pmd fragment support.
No functional change in this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In later patch we switch pmd_lock from mm->page_table_lock to split pmd ptlock.
It avoid compilations issues, use pmd_lockptr helper.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only code movement and avoid #ifdef.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the next set of patches, we will switch pmd allocator to use page fragments
and the locking will be updated to split pmd ptlock. We want to avoid using
fragments for partition-scoped table. Use slab cache similar to level 4 table
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use new return type vm_fault_t for fault handler. For now, this is
just documenting that the function returns a VM_FAULT value rather
than an errno. Once all instances are converted, vm_fault_t will
become a distinct type. See commit 1c8f422059 ("mm: change return
type to vm_fault_t").
We are fixing a minor bug, that the error from vm_insert_pfn() was
being ignored and the effect of this is likely to be only felt in OOM
situations.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment we assume that IODA2 and newer PHBs can always do 4K/64K/16M
IOMMU pages, however this is not the case for POWER9 and now skiboot
advertises the supported sizes via the device so we use that instead
of hard coding the mask.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently memtrace doesn't build if NUMA=n:
In function ‘memtrace_alloc_node’:
arch/powerpc/platforms/powernv/memtrace.c:134:6:
error: the address of ‘contig_page_data’ will always evaluate as ‘true’
if (!NODE_DATA(nid) || !node_spanned_pages(nid))
^
This is because for NUMA=n NODE_DATA(nid) points to an always
allocated structure, contig_page_data.
But even in the NUMA=y case memtrace_alloc_node() is only called for
online nodes, and we should always have a NODE_DATA() allocated for an
online node. So remove the (hopefully) overly paranoid check, which
also means we can build when NUMA=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6a6928c3e ("of/fdt: Convert FDT functions to use
libfdt") (Apr 2014), the generic flat device tree code dropped support
for flat device tree's older than version 0x10 (16).
We still have code in our CPU scanning to cope with flat device tree
versions earlier than 2, which can now never trigger, so drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a test of the relative branch patching logic in the alternate
section feature fixup code. This tests that if we branch past the last
instruction of the alternate section, the branch is not patched.
That's because the assembler will have created a branch that already
points to the first instruction after the patched section, which is
correct and needs no further patching.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We want this to remain the last test (because it's disabled by
default), so give it a non-numbered name so we don't have to renumber
it when adding new tests before it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code patching code has always been a bit confused about whether
it's best to use void *, unsigned int *, char *, etc. to point to
instructions. In fact in the feature fixups tests we use both unsigned
int[] and u8[] in different places.
Unfortunately the tests that use unsigned int[] calculate the size of
the code blocks using subtraction of those unsigned int pointers, and
then pass the result to memcmp(). This means we're only comparing 1/4
of the bytes we need to, because we need to multiply by
sizeof(unsigned int) to get the number of *bytes*.
The result is that the tests do all the patching and then only compare
some of the resulting code, so patching bugs that only effect that
last 3/4 of the code could slip through undetected. It turns out that
hasn't been happening, although one test had a bad expected case (see
previous commit).
Fix it for now by multiplying the size by 4 in the affected functions.
Fixes: 362e7701fd ("powerpc: Add self-tests of the feature fixup code")
Epic-brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The expected case for this test was wrong, the source of the alternate
code sequence is:
FTR_SECTION_ELSE
2: or 2,2,2
PPC_LCMPI r3,1
beq 3f
blt 2b
b 3f
b 1b
ALT_FTR_SECTION_END(0, 1)
3: or 1,1,1
or 2,2,2
4: or 3,3,3
So when it's patched the '3' label should still be on the 'or 1,1,1',
and the 4 label is irrelevant and can be removed.
Fixes: 362e7701fd ("powerpc: Add self-tests of the feature fixup code")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the systbl_chk.sh checks fail we print a message, but with no
indication that it's an error. That makes it hard to find in build
logs with eg. grep.
So prefix any output with "Error:".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
it had always been pointless - compat_sys_select() sign-extends
the first argument just fine on its own.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Use COMPAT_SPU_NEW() to keep systbl_chk.sh happy]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the select system call is wired up with the SYSX_SPU()
macro. The SYSX_SPU() is not handled by systbl_chk.c, which means the
syscall number for select is not checked.
That hides the fact that the syscall number for select is actually
__NR__newselect not __NR_select.
In a following patch we'd like to drop ppc32_select() which means
select will become a regular COMPAT_SYS_SPU() syscall. But
COMPAT_SYS_SPU() can't deal with the fact that the syscall number is
actually __NR__newselect. We also can't just redefine __NR_select
because that's still used for the old select call.
So add a new COMPAT_NEW_SPU() that does the same thing as
COMPAT_SYS_SPU() except it encodes that we're using the new number.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Fix sys_debug_setcontext() prototype to return long]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "Power Architecture 64-Bit ELF V2 ABI" says in section 2.3.2.3:
[...] There are several rules that must be adhered to in order to ensure
reliable and consistent call chain backtracing:
* Before a function calls any other function, it shall establish its
own stack frame, whose size shall be a multiple of 16 bytes.
– In instances where a function’s prologue creates a stack frame, the
back-chain word of the stack frame shall be updated atomically with
the value of the stack pointer (r1) when a back chain is implemented.
(This must be supported as default by all ELF V2 ABI-compliant
environments.)
[...]
– The function shall save the link register that contains its return
address in the LR save doubleword of its caller’s stack frame before
calling another function.
To me this sounds like the equivalent of HAVE_RELIABLE_STACKTRACE.
This patch may be unneccessarily limited to ppc64le, but OTOH the only
user of this flag so far is livepatching, which is only implemented on
PPCs with 64-LE, a.k.a. ELF ABI v2.
Feel free to add other ppc variants, but so far only ppc64le got tested.
This change also implements save_stack_trace_tsk_reliable() for ppc64le
that checks for the above conditions, where possible.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide timebase and timebase of last heartbeat in watchdog lockup
messages. Also provide a stack trace of when a CPU becomes un-stuck,
which can be useful -- it could be where irqs are re-enabled, so it
may be the end of the critical section which is responsible for the
latency which is useful information.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The watchdog heartbeat timestamp is updated when the local heartbeat
timer fires (or touch_nmi_watchdog() is called).
This is an interesting data point, so don't overwrite it when the
soft-NMI interrupt detects a hard lockup. That code came from a pre-
merge version to prevent hard lockup messages flood, but that's taken
care of with the stuck CPU logic now, so there is no reason to
update the heartbeat timestamp here.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is not the case for the moment, but future releases of pHyp might
need to introduce some synchronisation routines under the hood which
would make the XIVE hcalls longer to complete.
As this was done for H_INT_RESET, let's wrap the other hcalls in a
loop catching the H_LONG_BUSY_* codes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hcall H_INT_RESET should be called to make sure XIVE is fully
reseted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hcall H_INT_RESET can take some time to complete and in such cases
it returns H_LONG_BUSY_* codes requiring the machine to sleep for a
while before retrying.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kexec_state KEXEC_STATE_IRQS_OFF barrier is reached by all
secondary CPUs before the kexec_cpu_down() operation is called on
secondaries. This can raise conflicts and provoque errors in the XIVE
hcalls when XIVE is shutdown with H_INT_RESET on the primary CPU.
To synchronize the kexec_cpu_down() operations and make sure the
secondaries have completed their task before the primary starts doing
the same, let's move the primary kexec_cpu_down() after the
KEXEC_STATE_REAL_MODE barrier.
This change of the ending sequence of kexec is mostly useful on the
pseries platform but it impacts also the powernv, ps3 and 85xx
platforms. powernv can be easily tested and fixed but some caution is
required for the other two.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For consideration:
* Add NVDIMM support - Enables greater testing, mambo device.
* Add IPv6 support built in + additional modules - Because it's 2018 maan.
* Add DEFERRED_STRUCT_PAGE_INIT - Let's see what breaks.
* Add PPC_MEMTRACE - Small powernv debugfs driver for getting hardware traces.
* Add MEMORY_FAILURE - Machine check exceptions can now drive memory failure.
* Turn on FANOTIFY - This is the current filesystem notification feature.
* Turn on SCOM_DEBUGFS - Handy for hardware/firmware debugging, security risk?
* Turn on async SCSI scanning - Let's see what breaks.
* Add MLX5 driver as a module - Popular demand.
* Add CRYPTO_CRCT10DIF_VPMSUM - POWER8 T10DIF acceleration.
* Make a bunch of USB hid drivers modules.
* Make SCSI SG, SR, and FC modules - FC is huge.
* Make video drivers except AST GPU modules - Also huge.
* Make PCI serial driver a module - Uncommon.
* Make more things modules, NFS FS, RAM disk, netconsole, MS-DOS fs.
* Get rid of /dev/port - Not used.
* Remove PPS and PTP subsystms - Unusual.
* Remove legacy BSD ttys - Long dead.
* Remove IDE - Deprecated and replaced with ATA.
* Remove WIRELESS - Until we get POWER9 laptops.
* Remove RAW - Long deprecated in favour of direct IO.
* Remove floppy, parport, and PS2 input devices - not supported.
* Remove virtio drivers, ballooning - We're host only.
* Remove PPP - Sorry Paulus.
This results in a significantly smaller vmlinux:
text data bss dec filename
13143383 5277944 1317856 19739183 vanilla
12263281 4852074 1341720 18457075 patched
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The B43 driver only needs CONFIG_SSB to support the WLAN card found in
the Wii. Configure it accordingly, and disable BCMA bus support to save
a bit of space.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows access to the SD card and the BCM4318 Wifi module.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that there's a GPIO driver for the Wii, let's enable the following
drivers:
- the GPIO driver itself
- gpio-keys
- gpio-poweroff
- gpio-leds and a few LED triggers
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Wii doesn't have built-in Ethernet and USB Ethernet adapters are in
a different menu. Disable CONFIG_ETHERNET to save some space in support
code for Ethernet drivers.
Note that this patch doesn't disable any Ethernet drivers, because they
are not enabled by default.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hcall_exit() tracepoint has retval defined as unsigned long. That
leads to humours results like:
bash-3686 [009] d..2 854.134094: hcall_entry: opcode=24
bash-3686 [009] d..2 854.134095: hcall_exit: opcode=24 retval=18446744073709551609
It's normal for some hcalls to return negative values, displaying them
as unsigned isn't very helpful. So change it to signed.
bash-3711 [001] d..2 471.691008: hcall_entry: opcode=24
bash-3711 [001] d..2 471.691008: hcall_exit: opcode=24 retval=-7
Which can be more easily compared to H_NOT_FOUND in hvcall.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Now that we've updated the generic headers to support 5 PKEY bits for
powerpc we don't need our own #defines in arch code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Consolidate the pkey handling by providing a common empty definition
of vma_pkey() in pkeys.h when CONFIG_ARCH_HAS_PKEYS=n.
This also removes another entanglement of pkeys.h and
asm/mmu_context.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
VM_PKEY_BITx are defined only if CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS
is enabled. Powerpc also needs these bits. Hence lets define the
VM_PKEY_BITx bits for any architecture that enables
CONFIG_ARCH_HAS_PKEYS.
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The build is failing with CONFIG_NUMA=n and some compiler versions:
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_online_cpu':
hotplug-cpu.c:(.text+0x12c): undefined reference to `timed_topology_update'
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_cpu_remove':
hotplug-cpu.c:(.text+0x400): undefined reference to `timed_topology_update'
Fix it by moving the empty version of timed_topology_update() into the
existing #ifdef block, which has the right guard of SPLPAR && NUMA.
Fixes: cee5405da4 ("powerpc/hotplug: Improve responsiveness of hotplug change")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some syscall entry functions on powerpc are prefixed with
ppc_/ppc32_/ppc64_ rather than the usual sys_/__se_sys prefix. fork(),
clone(), swapcontext() are some examples of syscalls with such entry
points. We need to match against these names when initializing ftrace
syscall tracing.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On powerpc64 ABIv1, we are enabling syscall tracing for only ~20
syscalls. This is due to commit e145242ea0 ("syscalls/core,
syscalls/x86: Clean up syscall stub naming convention") which has
changed the syscall entry wrapper prefix from "SyS" to "__se_sys".
Update the logic for ABIv1 to not just skip the initial dot, but also
the "__se_sys" prefix.
Fixes: commit e145242ea0 ("syscalls/core, syscalls/x86: Clean up syscall stub naming convention")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 4e26bc4a4e ("powerpc/64: Rename soft_enabled to
irq_soft_mask") we renamed paca->soft_enabled. But then in commit
8e0b634b13 ("powerpc/64s: Do not allocate lppaca if we are not
virtualized") we added it back. Oops. This happened because the two
patches were in flight at the same time and rebased vs each other
multiple times, and we missed it in review.
Fixes: 8e0b634b13 ("powerpc/64s: Do not allocate lppaca if we are not virtualized")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit was a stop-gap to prevent crashes on hotunplug, caused by
the mismatch between the 1G mappings used for the linear mapping and the
memory block size. Those issues are now resolved because we split the
linear mapping at hotunplug time if necessary, as implemented in commit
4dd5f8a99e ("powerpc/mm/radix: Split linear mapping on hot-unplug").
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By using IS_ENABLED() we can simplify __set_pte_at() by removing
redundant *ptep = pte.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When nohash and book3s header were split, some hash related stuff
remained in the nohash header. This patch removes them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Duplicate pte_young() to avoid circular header dependency]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.
Fixes: b500afff11 ("fadump: Invalidate registration and release reserved memory for general use.")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
FADump capture kernel boots in restricted memory environment preserving
the context of previous kernel to save vmcore. Supporting hugepages in
such environment makes things unnecessarily complicated, as hugepages
need memory set aside for them. This means most of the capture kernel's
memory is used in supporting hugepages. In most cases, this results in
out-of-memory issues while booting FADump capture kernel. But hugepages
are not of much use in capture kernel whose only job is to save vmcore.
So, disabling hugepages support, when fadump is active, is a reliable
solution for the out of memory issues. Introducing a flag variable to
disable HugeTLB support when fadump is active.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The second kernel, during early boot after the crash, reserves rest of
the memory above boot memory size to make sure it does not touch any of the
dump memory area. It uses memblock_reserve() that reserves the specified
memory region irrespective of memory holes present within that region.
There are chances where previous kernel would have hot removed some of
its memory leaving memory holes behind. In such cases fadump kernel reports
incorrect number of reserved pages through arch_reserved_kernel_pages()
hook causing kernel to hang or panic.
Fix this by excluding memory holes while reserving rest of the memory
above boot memory size during second kernel boot after crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I no longer have a functional version of this board for even the most
basic sanity boot testing, and they have not been available for purchase
for quite some years now.
There is no point in adding a burden to testing coverage that does
walk all the possible defconfigs, so with all the above in mind, it
makes sense to remove it. Of course it will remain in the git history
for anyone who happens to stumble on one and wants to tinker with it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We've had dynamic ftrace support for over 9 years since Steve first
wrote it, all the distros use dynamic, and static is basically
untested these days, so drop support for static ftrace.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With -mprofile-kernel, we always save the full register state in
ftrace_caller(). While this works, this is inefficient if we're not
interested in the register state, such as when we're using the function
tracer.
Rename the existing ftrace_caller() as ftrace_regs_caller() and provide
a simpler implementation for ftrace_caller() that is used when registers
are not required to be saved.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Our implementation matches that of the generic version, which also
handles FTRACE_UPDATE_MODIFY_CALL. So, remove our implementation in
favor of the generic version.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For R_PPC64_REL24 relocations, we suppress emitting instructions for TOC
load/restore in the relocation stub if the relocation is for _mcount()
call when using -mprofile-kernel ABI.
To detect this, we check if the preceding instructions are per the
standard set of instructions emitted by gcc: either the two instruction
sequence of 'mflr r0; std r0,16(r1)', or the more optimized variant of a
single 'mflr r0'. This is not sufficient since nothing prevents users
from hand coding sequences involving a 'mflr r0' followed by a 'bl'.
For removing the toc save instruction from the stub, we additionally
check if the symbol is "_mcount". Add the same check here as well.
Also rename is_early_mcount_callsite() to is_mprofile_mcount_callsite()
since that is what is being checked. The use of "early" is misleading
since there is nothing involving this function that qualifies as early.
Fixes: 153086644f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If function_graph tracer is enabled during kexec, we see the below
exception in the simulator:
root@(none):/# kexec -e
kvm: exiting hardware virtualization
kexec_core: Starting new kernel
[ 19.262020070,5] OPAL: Switch to big-endian OS
kexec: Starting switchover sequence.
Interrupt to 0xC000000000004380 from 0xC000000000004380
** Execution stopped: Continuous Interrupt, Instruction caused exception, **
Now that we have a more effective way to completely disable ftrace on
ppc64, let's also use that before switching to a new kernel during
kexec.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During guest entry/exit, we switch over to/from the guest MMU context
and we cannot take exceptions in the hypervisor code.
Since ftrace may be enabled and since it can result in us taking a trap,
disable ftrace by setting paca->ftrace_enabled to zero. There are two
paths through which we enter/exit a guest:
1. If we are the vcore runner, then we enter the guest via
__kvmppc_vcore_entry() and we disable ftrace around this. This is always
the case for Power9, and for the primary thread on Power8.
2. If we are a secondary thread in Power8, then we would be in nap due
to SMT being disabled. We are woken up by an IPI to enter the guest. In
this scenario, we enter the guest through kvm_start_guest(). We disable
ftrace at this point. In this scenario, ftrace would only get re-enabled
on the secondary thread when SMT is re-enabled (via start_secondary()).
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Disable ftrace when a cpu is about to go offline. When the cpu is woken
up, ftrace will get enabled in start_secondary().
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On the boot cpu, though we enable paca->ftrace_enabled in early_setup()
(via cpu_ready_for_interrupts()), we don't start tracing until much
later since ftrace is not initialized yet and since we only support
DYNAMIC_FTRACE on powerpc. However, it is possible that ftrace has been
initialized by the time some of the secondary cpus start up. In this
case, we will try to trace some of the early boot code which can cause
problems.
To address this, move setting paca->ftrace_enabled from
cpu_ready_for_interrupts() to early_setup() for the boot cpu, and towards
the end of start_secondary() for secondary cpus.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add some helpers to enable/disable ftrace through paca->ftrace_enabled.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Re-arrange the last #ifdef section in preparation for a subsequent
change.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some C code that we call into from real mode where we cannot
take any exceptions. Though the C functions themselves are mostly safe,
if these functions are traced, there is a possibility that we may take
an exception. For instance, in certain conditions, the ftrace code uses
WARN(), which uses a 'trap' to do its job.
For such scenarios, introduce a new field in paca 'ftrace_enabled',
which is checked on ftrace entry before continuing. This field can then
be set to zero to disable/pause ftrace, and set to a non-zero value to
resume ftrace.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
smp_send_stop can lock up the IPI path for any subsequent calls,
because the receiving CPUs spin in their handler function. This
started becoming a problem with the addition of an smp_send_stop
call in the reboot path, because panics can reboot after doing
their own smp_send_stop.
The NMI IPI variant was fixed with ac61c11566 ("powerpc: Fix
smp_send_stop NMI IPI handling"), which leaves the smp_call_function
variant.
This is fixed by having smp_send_stop only ever do the
smp_call_function once. This is a bit less robust than the NMI IPI
fix, because any other call to smp_call_function after smp_send_stop
could deadlock, but that has always been the case, and it was not
been a problem before.
Fixes: f2748bdfe1 ("powerpc/powernv: Always stop secondaries before reboot/shutdown")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The NMI IPI handler for a receiving CPU increments nmi_ipi_busy_count
over the handler function call, which causes later smp_send_nmi_ipi()
callers to spin until the call is finished.
The stop_this_cpu() function never returns, so the busy count is never
decremeted, which can cause the system to hang in some cases. For
example panic() will call smp_send_stop() early on which calls
stop_this_cpu() on other CPUs, then later in the reboot path,
pnv_restart() will call smp_send_stop() again, which hangs.
Fix this by adding a special case to the stop_this_cpu() handler to
decrement the busy count, because it will never return.
Now that the NMI/non-NMI versions of stop_this_cpu() are different,
split them out into separate functions rather than doing #ifdef tricks
to share the body between the two functions.
Fixes: 6bed323762 ("powerpc: use NMI IPI for smp_send_stop")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out the functions, tweak change log a bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OPAL RTC driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, up to 50 seconds have been observed here when RTC stops
responding (BMC reboot can do it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5a ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current code extracts the physical address for UE errors and then
hooks it up into memory failure infrastructure. On successful
extraction of physical address it wrongly sets "handled = 1" which
means this UE error has been recovered. Since MCE handler gets return
value as handled = 1, it assumes that error has been recovered and
goes back to same NIP. This causes MCE interrupt again and again in a
loop leading to hard lockup.
Also, initialize phys_addr to ULONG_MAX so that we don't end up
queuing undesired page to hwpoison.
Without this patch we see:
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
...
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Memory failure: 0x20181a08: recovery action for dirty LRU page: Recovered
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
...
Watchdog CPU:38 Hard LOCKUP
After this patch we see:
Severe Machine check interrupt [Not recovered]
NIP: [00007fffaae585f4] PID: 7168 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffaafe28ac
Physical address: 00002017c0bd0000
find[7168]: unhandled signal 7 at 00007fffaae585f4 nip 00007fffaae585f4 lr 00007fffaae585e0 code 4
Memory failure: 0x2017c0bd: recovery action for dirty LRU page: Recovered
Fixes: 01eaac2b05 ("powerpc/mce: Hookup ierror (instruction) UE errors")
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().
At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.
It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.
The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.
The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.
These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.
The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 95846ecf9d ("pid: replace pid bitmap implementation with IDR
API") changed last field of /proc/loadavg (last pid allocated) to be off
by one:
# unshare -p -f --mount-proc cat /proc/loadavg
0.00 0.00 0.00 1/60 2 <===
It should be 1 after first fork into pid namespace.
This is formally a regression but given how useless this field is I
don't think anyone is affected.
Bug was found by /proc testsuite!
Link: http://lkml.kernel.org/r/20180413175408.GA27246@avx2
Fixes: 95846ecf9d ("pid: replace pid bitmap implementation with IDR API")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gargi Sharma <gs051095@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running KVM guests on Power8 we can see a lockup where one CPU
stops responding. This often leads to a message such as:
watchdog: CPU 136 detected hard LOCKUP on other CPUs 72
Task dump for CPU 72:
qemu-system-ppc R running task 10560 20917 20908 0x00040004
And then backtraces on other CPUs, such as:
Task dump for CPU 48:
ksmd R running task 10032 1519 2 0x00000804
Call Trace:
...
--- interrupt: 901 at smp_call_function_many+0x3c8/0x460
LR = smp_call_function_many+0x37c/0x460
pmdp_invalidate+0x100/0x1b0
__split_huge_pmd+0x52c/0xdb0
try_to_unmap_one+0x764/0x8b0
rmap_walk_anon+0x15c/0x370
try_to_unmap+0xb4/0x170
split_huge_page_to_list+0x148/0xa30
try_to_merge_one_page+0xc8/0x990
try_to_merge_with_ksm_page+0x74/0xf0
ksm_scan_thread+0x10ec/0x1ac0
kthread+0x160/0x1a0
ret_from_kernel_thread+0x5c/0x78
This is caused by commit 8c1c7fb0b5 ("powerpc/64s/idle: avoid sync
for KVM state when waking from idle"), which added a check in
pnv_powersave_wakeup() to see if the kvm_hstate.hwthread_state is
already set to KVM_HWTHREAD_IN_KERNEL, and if so to skip the store and
test of kvm_hstate.hwthread_req.
The problem is that the primary does not set KVM_HWTHREAD_IN_KVM when
entering the guest, so it can then come out to cede with
KVM_HWTHREAD_IN_KERNEL set. It can then go idle in kvm_do_nap after
setting hwthread_req to 1, but because hwthread_state is still
KVM_HWTHREAD_IN_KERNEL we will skip the test of hwthread_req when we
wake up from idle and won't go to kvm_start_guest. From there the
thread will return somewhere garbage and crash.
Fix it by skipping the store of hwthread_state, but not the test of
hwthread_req, when coming out of idle. It's OK to skip the sync in
that case because hwthread_req will have been set on the same thread,
so there is no synchronisation required.
Fixes: 8c1c7fb0b5 ("powerpc/64s/idle: avoid sync for KVM state when waking from idle")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On boot we save the configuration space of PCIe bridges. We do this so
when we get an EEH event and everything gets reset that we can restore
them.
Unfortunately we save this state before we've enabled the MMIO space
on the bridges. Hence if we have to reset the bridge when we come back
MMIO is not enabled and we end up taking an PE freeze when the driver
starts accessing again.
This patch forces the memory/MMIO and bus mastering on when restoring
bridges on EEH. Ideally we'd do this correctly by saving the
configuration space writes later, but that will have to come later in
a larger EEH rewrite. For now we have this simple fix.
The original bug can be triggered on a boston machine by doing:
echo 0x8000000000000000 > /sys/kernel/debug/powerpc/PCI0001/err_injct_outbound
On boston, this PHB has a PCIe switch on it. Without this patch,
you'll see two EEH events, 1 expected and 1 the failure we are fixing
here. The second EEH event causes the anything under the PHB to
disappear (i.e. the i40e eth).
With this patch, only 1 EEH event occurs and devices properly recover.
Fixes: 652defed48 ("powerpc/eeh: Check PCIe link after reset")
Cc: stable@vger.kernel.org # v3.11+
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When setting up a CPU, we "push" (activate) a pool VP for it.
However it's an error to do so if it already has an active
pool VP.
This happens when doing soft CPU hotplug on powernv since we
don't tear down the CPU on unplug. The HW flags the error which
gets captured by the diagnostics.
Fix this by making sure to "pull" out any already active pool
first.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If there is no d-cache-size property in the device tree, l1d_size could
be zero. We don't actually expect that to happen, it's only been seen
on mambo (simulator) in some configurations.
A zero-size l1d_size leads to the loop in the asm wrapping around to
2^64-1, and then walking off the end of the fallback area and
eventually causing a page fault which is fatal.
Just default to 64K which is correct on some CPUs, and sane enough to
not cause a crash on others.
Fixes: aa8a5e0062 ('powerpc/64s: Add support for RFI flush of L1-D cache')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Rewrite comment and change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we patch an alternate feature section, we have to adjust any
relative branches that branch out of the alternate section.
But currently we have a bug if we have a branch that points to past
the last instruction of the alternate section, eg:
FTR_SECTION_ELSE
1: b 2f
or 6,6,6
2:
ALT_FTR_SECTION_END(...)
nop
This will result in a relative branch at 1 with a target that equals
the end of the alternate section.
That branch does not need adjusting when it's moved to the non-else
location. Currently we do adjust it, resulting in a branch that goes
off into the link-time location of the else section, which is junk.
The fix is to not patch branches that have a target == end of the
alternate section.
Fixes: d20fe50a7b ("KVM: PPC: Book3S HV: Branch inside feature section")
Fixes: 9b1a735de6 ("powerpc: Add logic to patch alternative feature sections")
Cc: stable@vger.kernel.org # v2.6.27+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix crashes when loading modules built with a different CONFIG_RELOCATABLE
value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error conditions
from firmware.
- Remove tlbie trace points from KVM code that's called in real mode, because
it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is actually the
minimal set when we build with support for firmware supplied CPU features.
Thanks to:
Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=0e7c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes when loading modules built with a different
CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error
conditions from firmware.
- Remove tlbie trace points from KVM code that's called in real mode,
because it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is
actually the minimal set when we build with support for firmware
supplied CPU features.
Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
powerpc/8xx: Fix build with hugetlbfs enabled
powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
powerpc/fscr: Enable interrupts earlier before calling get_user()
powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic
For s390 new kernels are loaded to fixed addresses in memory before they
are booted. With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address. In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.
Luckily there is a simple workaround for this problem. By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This
allows the architecture to set kbuf->mem by hand. While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.
Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it. With this change
architectures have access to the buffer and can edit it as they need.
A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field. As now the information
stored there can directly be accessed from kbuf->mem.
Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As arch_kexec_kernel_image_{probe,load}(),
arch_kimage_file_post_load_cleanup() and arch_kexec_kernel_verify_sig()
are almost duplicated among architectures, they can be commonalized with
an architecture-defined kexec_file_ops array. So let's factor them out.
Link: http://lkml.kernel.org/r/20180306102303.9063-3-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kexec_file, x86, powerpc: refactoring for other
architecutres", v2.
This is a preparatory patchset for adding kexec_file support on arm64.
It was originally included in a arm64 patch set[1], but Philipp is also
working on their kexec_file support on s390[2] and some changes are now
conflicting.
So these common parts were extracted and put into a separate patch set
for better integration. What's more, my original patch#4 was split into
a few small chunks for easier review after Dave's comment.
As such, the resulting code is basically identical with my original, and
the only *visible* differences are:
- renaming of _kexec_kernel_image_probe() and _kimage_file_post_load_cleanup()
- change one of types of arguments at prepare_elf64_headers()
Those, unfortunately, require a couple of trivial changes on the rest
(#1, #6 to #13) of my arm64 kexec_file patch set[1].
Patch #1 allows making a use of purgatory optional, particularly useful
for arm64.
Patch #2 commonalizes arch_kexec_kernel_{image_probe, image_load,
verify_sig}() and arch_kimage_file_post_load_cleanup() across
architectures.
Patches #3-#7 are also intended to generalize parse_elf64_headers(),
along with exclude_mem_range(), to be made best re-use of.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-February/561182.html
[2] http://lkml.iu.edu//hypermail/linux/kernel/1802.1/02596.html
This patch (of 7):
On arm64, crash dump kernel's usable memory is protected by *unmapping*
it from kernel virtual space unlike other architectures where the region
is just made read-only. It is highly unlikely that the region is
accidentally corrupted and this observation rationalizes that digest
check code can also be dropped from purgatory. The resulting code is so
simple as it doesn't require a bit ugly re-linking/relocation stuff,
i.e. arch_kexec_apply_relocations_add().
Please see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2017-December/545428.html
All that the purgatory does is to shuffle arguments and jump into a new
kernel, while we still need to have some space for a hash value
(purgatory_sha256_digest) which is never checked against.
As such, it doesn't make sense to have trampline code between old kernel
and new kernel on arm64.
This patch introduces a new configuration, ARCH_HAS_KEXEC_PURGATORY, and
allows related code to be compiled in only if necessary.
[takahiro.akashi@linaro.org: fix trivial screwup]
Link: http://lkml.kernel.org/r/20180309093346.GF25863@linaro.org
Link: http://lkml.kernel.org/r/20180306102303.9063-2-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cpu_has_feature() mechanism has an optimisation where at build
time we construct a mask of the CPU feature bits that will always be
true for the given .config, based on the platform/bitness/etc. that we
are building for.
That is incompatible with DT CPU features, where the set of CPU
features is dependent on feature flags that are given to us by
firmware.
The result is that some feature bits can not be *disabled* by DT CPU
features. Or more accurately, they can be disabled but they will still
appear in the ALWAYS mask, meaning cpu_has_feature() will always
return true for them.
In the past this hasn't really been a problem because on Book3S
64 (where we support DT CPU features), the set of ALWAYS bits has been
very small. That was because we always built for POWER4 and later,
meaning the set of common bits was small.
The only bit that could be cleared by DT CPU features that was also in
the ALWAYS mask was CPU_FTR_NODSISRALIGN, and that was only used in
the alignment handler to create a fake DSISR. That code was itself
deleted in 31bfdb036f ("powerpc: Use instruction emulation
infrastructure to handle alignment faults") (Sep 2017).
However the set of ALWAYS features changed with the recent commit
db5ae1c155 ("powerpc/64s: Refine feature sets for little endian
builds") which restricted the set of feature flags when building
little endian to Power7 or later. That caused the ALWAYS mask to
become much larger for little endian builds.
The result is that the following feature bits can currently not
be *disabled* by DT CPU features:
CPU_FTR_REAL_LE, CPU_FTR_MMCRA, CPU_FTR_CTRL, CPU_FTR_SMT,
CPU_FTR_PURR, CPU_FTR_SPURR, CPU_FTR_DSCR, CPU_FTR_PKEY,
CPU_FTR_VMX_COPY, CPU_FTR_CFAR, CPU_FTR_HAS_PPR.
To fix it we need to mask the set of ALWAYS features with the base set
of DT CPU features, ie. the features that are always enabled by DT CPU
features. That way there are no bits in the ALWAYS mask that are not
also always set by DT CPU features.
Fixes: db5ae1c155 ("powerpc/64s: Refine feature sets for little endian builds")
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In tlbiel_radix_set_isa300() we use the PPC_TLBIEL() macro to
construct tlbiel instructions. The instruction takes 5 fields, two of
which are registers, and the others are constants. But because it's
constructed with inline asm the compiler doesn't know that.
We got the constraint wrong on the 'r' field, using "r" tells the
compiler to put the value in a register. The value we then get in the
macro is the *register number*, not the value of the field.
That means when we mask the register number with 0x1 we get 0 or 1
depending on which register the compiler happens to put the constant
in, eg:
li r10,1
tlbiel r8,r9,2,0,0
li r7,1
tlbiel r10,r6,0,0,1
If we're unlucky we might generate an invalid instruction form, for
example RIC=0, PRS=1 and R=0, tlbiel r8,r7,0,1,0, this has been
observed to cause machine checks:
Oops: Machine check, sig: 7 [#1]
CPU: 24 PID: 0 Comm: swapper
NIP: 00000000000385f4 LR: 000000000100ed00 CTR: 000000000000007f
REGS: c00000000110bb40 TRAP: 0200
MSR: 9000000000201003 <SF,HV,ME,RI,LE> CR: 48002222 XER: 20040000
CFAR: 00000000000385d0 DAR: 0000000000001c00 DSISR: 00000200 SOFTE: 1
If the machine check happens early in boot while we have MSR_ME=0 it
will escalate into a checkstop and kill the box entirely.
To fix it we could change the inline asm constraint to "i" which
tells the compiler the value is a constant. But a better fix is to just
pass a literal 1 into the macro, which bypasses any problems with inline
asm constraints.
Fixes: d4748276ae ("powerpc/64s: Improve local TLB flush for boot and MCE on POWER9")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Patch series "exec: Pin stack limit during exec".
Attempts to solve problems with the stack limit changing during exec
continue to be frustrated[1][2]. In addition to the specific issues
around the Stack Clash family of flaws, Andy Lutomirski pointed out[3]
other places during exec where the stack limit is used and is assumed to
be unchanging. Given the many places it gets used and the fact that it
can be manipulated/raced via setrlimit() and prlimit(), I think the only
way to handle this is to move away from the "current" view of the stack
limit and instead attach it to the bprm, and plumb this down into the
functions that need to know the stack limits. This series implements
the approach.
[1] 04e35f4495 ("exec: avoid RLIMIT_STACK races with prlimit()")
[2] 779f4e1c6c ("Revert "exec: avoid RLIMIT_STACK races with prlimit()"")
[3] to security@kernel.org, "Subject: existing rlimit races?"
This patch (of 3):
Since it is possible that the stack rlimit can change externally during
exec (either via another thread calling setrlimit() or another process
calling prlimit()), provide a way to pass the rlimit down into the
per-architecture mm layout functions so that the rlimit can stay in the
bprm structure instead of sitting in the signal structure until exec is
finalized.
Link: http://lkml.kernel.org/r/1518638796-20819-2-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hugh Dickins <hughd@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No allocation callback is using this argument anymore. new_page_node
used to use this parameter to convey node_id resp. migration error up
to move_pages code (do_move_page_to_node_array). The error status never
made it into the final status field and we have a better way to
communicate node id to the status field now. All other allocation
callbacks simply ignored the argument so we can drop it finally.
[mhocko@suse.com: fix migration callback]
Link: http://lkml.kernel.org/r/20180105085259.GH2801@dhcp22.suse.cz
[akpm@linux-foundation.org: fix alloc_misplaced_dst_page()]
[mhocko@kernel.org: fix build]
Link: http://lkml.kernel.org/r/20180103091134.GB11319@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20180103082555.14592-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This crashes with a "Bad real address for load" attempting to load
from the vmalloc region in realmode (faulting address is in DAR).
Oops: Bad interrupt in KVM entry/exit code, sig: 6 [#1]
LE SMP NR_CPUS=2048 NUMA PowerNV
CPU: 53 PID: 6582 Comm: qemu-system-ppc Not tainted 4.16.0-01530-g43d1859f0994
NIP: c0000000000155ac LR: c0000000000c2430 CTR: c000000000015580
REGS: c000000fff76dd80 TRAP: 0200 Not tainted (4.16.0-01530-g43d1859f0994)
MSR: 9000000000201003 <SF,HV,ME,RI,LE> CR: 48082222 XER: 00000000
CFAR: 0000000102900ef0 DAR: d00017fffd941a28 DSISR: 00000040 SOFTE: 3
NIP [c0000000000155ac] perf_trace_tlbie+0x2c/0x1a0
LR [c0000000000c2430] do_tlbies+0x230/0x2f0
I suspect the reason is the per-cpu data is not in the linear chunk.
This could be restored if that was able to be fixed, but for now,
just remove the tracepoints.
Fixes: 0428491cba ("powerpc/mm: Trace tlbie(l) instructions")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
8xx uses the slice code when hugetlbfs is enabled. We missed a header
include on 8xx which resulted in the below build failure:
config: mpc885_ads_defconfig + CONFIG_HUGETLBFS
arch/powerpc/mm/slice.c: In function 'slice_get_unmapped_area':
arch/powerpc/mm/slice.c:655:2: error: implicit declaration of function 'need_extra_context'
arch/powerpc/mm/slice.c:656:3: error: implicit declaration of function 'alloc_extended_context'
on PPC64 the mmu_context.h was included via linux/pkeys.h
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5a ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de9f ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* A rework of the filesytem-dax implementation provides for detection of
unmap operations (truncate / hole punch) colliding with in-progress
device-DMA. A fix for these collisions remains a work-in-progress
pending resolution of truncate latency and starvation regressions.
* The of_pmem driver expands the users of libnvdimm outside of x86 and
ACPI to describe an implementation of persistent memory on PowerPC with
Open Firmware / Device tree.
* Address Range Scrub (ARS) handling is completely rewritten to account for
the fact that ARS may run for 100s of seconds and there is no platform
defined way to cancel it. ARS will now no longer block namespace
initialization.
* The NVDIMM Namespace Label implementation is updated to handle label
areas as small as 1K, down from 128K.
* Miscellaneous cleanups and updates to unit test infrastructure.
-----BEGIN PGP SIGNATURE-----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=acZQ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This cycle was was not something I ever want to repeat as there were
several late changes that have only now just settled.
Half of the branch up to commit d2c997c0f1 ("fs, dax: use
page->mapping to warn...") have been in -next for several releases.
The of_pmem driver and the address range scrub rework were late
arrivals, and the dax work was scaled back at the last moment.
The of_pmem driver missed a previous merge window due to an oversight.
A sense of obligation to rectify that miss is why it is included for
4.17. It has acks from PowerPC folks. Stephen reported a build failure
that only occurs when merging it with your latest tree, for now I have
fixed that up by disabling modular builds of of_pmem. A test merge
with your tree has received a build success report from the 0day robot
over 156 configs.
An initial version of the ARS rework was submitted before the merge
window. It is self contained to libnvdimm, a net code reduction, and
passing all unit tests.
The filesystem-dax changes are based on the wait_var_event()
functionality from tip/sched/core. However, late review feedback
showed that those changes regressed truncate performance to a large
degree. The branch was rewound to drop the truncate behavior change
and now only includes preparation patches and cleanups (with full acks
and reviews). The finalization of this dax-dma-vs-trnucate work will
need to wait for 4.18.
Summary:
- A rework of the filesytem-dax implementation provides for detection
of unmap operations (truncate / hole punch) colliding with
in-progress device-DMA. A fix for these collisions remains a
work-in-progress pending resolution of truncate latency and
starvation regressions.
- The of_pmem driver expands the users of libnvdimm outside of x86
and ACPI to describe an implementation of persistent memory on
PowerPC with Open Firmware / Device tree.
- Address Range Scrub (ARS) handling is completely rewritten to
account for the fact that ARS may run for 100s of seconds and there
is no platform defined way to cancel it. ARS will now no longer
block namespace initialization.
- The NVDIMM Namespace Label implementation is updated to handle
label areas as small as 1K, down from 128K.
- Miscellaneous cleanups and updates to unit test infrastructure"
* tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (39 commits)
libnvdimm, of_pmem: workaround OF_NUMA=n build error
nfit, address-range-scrub: add module option to skip initial ars
nfit, address-range-scrub: rework and simplify ARS state machine
nfit, address-range-scrub: determine one platform max_ars value
powerpc/powernv: Create platform devs for nvdimm buses
doc/devicetree: Persistent memory region bindings
libnvdimm: Add device-tree based driver
libnvdimm: Add of_node to region and bus descriptors
libnvdimm, region: quiet region probe
libnvdimm, namespace: use a safe lookup for dimm device name
libnvdimm, dimm: fix dpa reservation vs uninitialized label area
libnvdimm, testing: update the default smart ctrl_temperature
libnvdimm, testing: Add emulation for smart injection commands
nfit, address-range-scrub: introduce nfit_spa->ars_state
libnvdimm: add an api to cast a 'struct nd_region' to its 'struct device'
nfit, address-range-scrub: fix scrub in-progress reporting
dax, dm: allow device-mapper to operate without dax support
dax: introduce CONFIG_DAX_DRIVER
fs, dax: use page->mapping to warn if truncate collides with a busy page
ext2, dax: introduce ext2_dax_aops
...
This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.
The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.
This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function get_user() can sleep while trying to fetch instruction
from user address space and causes the following warning from the
scheduler.
BUG: sleeping function called from invalid context
Though interrupts get enabled back but it happens bit later after
get_user() is called. This change moves enabling these interrupts
earlier covering the function get_user(). While at this, lets check
for kernel mode and crash as this interrupt should not have been
triggered from the kernel context.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():
The function setup_rfi_flush() references
the function __init ppc64_bolted_size().
the function __init memblock_alloc_base().
The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().
These references are safe because:
- only pseries calls setup_rfi_flush() at runtime
- pseries always passes L1D_FLUSH_FALLBACK at boot
- so the fallback flush area will always be allocated
- so the check in init_fallback_flush() will always return early:
/* Only allocate the fallback flush area once (at boot time). */
if (l1d_flush_fallback_area)
return;
- and therefore we won't actually call the freed init routines.
We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.
Fixes: abf110f3e1 ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past invalid
privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as of now)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJay19UAAoJEL/70l94x66DGKYIAIu9PTHAEwaX0et15fPW5y2x
rrtS355lSAmMrPJ1nePRQ+rProD/1B0Kizj3/9O+B9OTKKRsorRYNa4CSu9neO2k
N3rdE46M1wHAPwuJPcYvh3iBVXtgbMayk1EK5aVoSXaMXEHh+PWZextkl+F+G853
kC27yDy30jj9pStwnEFSBszO9ua/URdKNKBATNx8WUP6d9U/dlfm5xv3Dc3WtKt2
UMGmog2wh0i7ecXo7hRkMK4R7OYP3ZxAexq5aa9BOPuFp+ZdzC/MVpN+jsjq2J/M
Zq6RNyA2HFyQeP0E9QgFsYS2BNOPeLZnT5Jg1z4jyiD32lAZ/iC51zwm4oNKcDM=
=bPlD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past
invalid privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as
of now)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (174 commits)
kvm: x86: fix a prototype warning
kvm: selftests: add sync_regs_test
kvm: selftests: add API testing infrastructure
kvm: x86: fix a compile warning
KVM: X86: Add Force Emulation Prefix for "emulate the next instruction"
KVM: X86: Introduce handle_ud()
KVM: vmx: unify adjacent #ifdefs
x86: kvm: hide the unused 'cpu' variable
KVM: VMX: remove bogus WARN_ON in handle_ept_misconfig
Revert "KVM: X86: Fix SMRAM accessing even if VM is shutdown"
kvm: Add emulation for movups/movupd
KVM: VMX: raise internal error for exception during invalid protected mode state
KVM: nVMX: Optimization: Dont set KVM_REQ_EVENT when VMExit with nested_run_pending
KVM: nVMX: Require immediate-exit when event reinjected to L2 and L1 event pending
KVM: x86: Fix misleading comments on handling pending exceptions
KVM: x86: Rename interrupt.pending to interrupt.injected
KVM: VMX: No need to clear pending NMI/interrupt on inject realmode interrupt
x86/kvm: use Enlightened VMCS when running on Hyper-V
x86/hyper-v: detect nested features
x86/hyper-v: define struct hv_enlightened_vmcs and clean field bits
...
If you build the kernel with CONFIG_RELOCATABLE=n, then install the
modules, rebuild the kernel with CONFIG_RELOCATABLE=y and leave the
old modules installed, we crash something like:
Unable to handle kernel paging request for data at address 0xd000000018d66cef
Faulting instruction address: 0xc0000000021ddd08
Oops: Kernel access of bad area, sig: 11 [#1]
Modules linked in: x_tables autofs4
CPU: 2 PID: 1 Comm: systemd Not tainted 4.16.0-rc6-gcc_ubuntu_le-g99fec39 #1
...
NIP check_version.isra.22+0x118/0x170
Call Trace:
__ksymtab_xt_unregister_table+0x58/0xfffffffffffffcb8 [x_tables] (unreliable)
resolve_symbol+0xb4/0x150
load_module+0x10e8/0x29a0
SyS_finit_module+0x110/0x140
system_call+0x58/0x6c
This happens because since commit 71810db27c ("modversions: treat
symbol CRCs as 32 bit quantities"), a relocatable kernel encodes and
handles symbol CRCs differently from a non-relocatable kernel.
Although it's possible we could try and detect this situation and
handle it, it's much more robust to simply make the state of
CONFIG_RELOCATABLE part of the module vermagic.
Fixes: 71810db27c ("modversions: treat symbol CRCs as 32 bit quantities")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016 and no one
noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q Syndrome.
- A big series to make the allocation of our pacas (per cpu area), kernel page
tables, and per-cpu stacks NUMA aware when using the Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to:
Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy, Alistair Popple, Andy
Shevchenko, Aneesh Kumar K.V, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Christophe Leroy, Christophe Lombard, Cyril Bur, Daniel Axtens,
Dave Young, Finn Thain, Frederic Barrat, Gustavo Romero, Horia Geantă,
Jonathan Neuschäfer, Kees Cook, Larry Finger, Laurent Dufour, Laurent Vivier,
Logan Gunthorpe, Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus
Elfring, Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de
Oliveira, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher Boessenkool,
Simon Guo, Simon Horman, Stewart Smith, Sukadev Bhattiprolu, Suraj Jitindar
Singh, Thiago Jung Bauermann, Vaibhav Jain, Vaidyanathan Srinivasan, Vasant
Hegde, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----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=HAB1
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016
and no one noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory
on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on
Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs
files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q
Syndrome.
- A big series to make the allocation of our pacas (per cpu area),
kernel page tables, and per-cpu stacks NUMA aware when using the
Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to: Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy,
Alistair Popple, Andy Shevchenko, Aneesh Kumar K.V, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
Lombard, Cyril Bur, Daniel Axtens, Dave Young, Finn Thain, Frederic
Barrat, Gustavo Romero, Horia Geantă, Jonathan Neuschäfer, Kees Cook,
Larry Finger, Laurent Dufour, Laurent Vivier, Logan Gunthorpe,
Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus Elfring,
Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de Oliveira,
Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher
Boessenkool, Simon Guo, Simon Horman, Stewart Smith, Sukadev
Bhattiprolu, Suraj Jitindar Singh, Thiago Jung Bauermann, Vaibhav
Jain, Vaidyanathan Srinivasan, Vasant Hegde, Wei Yongjun"
* tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (207 commits)
powerpc/64s/idle: Fix restore of AMOR on POWER9 after deep sleep
powerpc/64s: Fix POWER9 DD2.2 and above in cputable features
powerpc/64s: Fix pkey support in dt_cpu_ftrs, add CPU_FTR_PKEY bit
powerpc/64s: Fix dt_cpu_ftrs to have restore_cpu clear unwanted LPCR bits
Revert "powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead"
powerpc: iomap.c: introduce io{read|write}64_{lo_hi|hi_lo}
powerpc: io.h: move iomap.h include so that it can use readq/writeq defs
cxl: Fix possible deadlock when processing page faults from cxllib
powerpc/hw_breakpoint: Only disable hw breakpoint if cpu supports it
powerpc/mm/radix: Update command line parsing for disable_radix
powerpc/mm/radix: Parse disable_radix commandline correctly.
powerpc/mm/hugetlb: initialize the pagetable cache correctly for hugetlb
powerpc/mm/radix: Update pte fragment count from 16 to 256 on radix
powerpc/mm/keys: Update documentation and remove unnecessary check
powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead
powerpc/64s/idle: Consolidate power9_offline_stop()/power9_idle_stop()
powerpc/powernv: Always stop secondaries before reboot/shutdown
powerpc: hard disable irqs in smp_send_stop loop
powerpc: use NMI IPI for smp_send_stop
powerpc/powernv: Fix SMT4 forcing idle code
...
Scan the devicetree for an nvdimm-bus compatible and create
a platform device for them.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- the v9fs maintainers have been missing for a long time. I've taken
over v9fs patch slinging.
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
mm,oom_reaper: check for MMF_OOM_SKIP before complaining
mm/ksm: fix interaction with THP
mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
headers: untangle kmemleak.h from mm.h
include/linux/mmdebug.h: make VM_WARN* non-rvals
mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
mm: change return type to vm_fault_t
mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
kernel/fork.c: detect early free of a live mm
mm: make counting of list_lru_one::nr_items lockless
mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
block_invalidatepage(): only release page if the full page was invalidated
mm: kernel-doc: add missing parameter descriptions
mm/swap.c: remove @cold parameter description for release_pages()
mm/nommu: remove description of alloc_vm_area
zram: drop max_zpage_size and use zs_huge_class_size()
zsmalloc: introduce zs_huge_class_size()
mm: fix races between swapoff and flush dcache
fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
...
