IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When converting the MSCC PHY driver to shared PHY packages, the Serdes
configuration in vsc8584_config_init was modified to use 'base_addr'
instead of 'base' as the port number. But 'base_addr' isn't equal to
'addr' for all PHYs inside the package, which leads to the Serdes still
being enabled on those ports. This patch fixes it.
Fixes: deb04e9c0ff2 ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 4f58e6dceb0e4 ("net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: cf41a51db8985 ("of/phylib: Use device tree properties to initialize Marvell PHYs.")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 2a10154abcb75 ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is set to be a module the code block is not
compiled. Use the IS_ENABLED macro that checks for both built in as
well as module.
Fixes: 01db923e83779 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ca23cb0bc50f ("mvneta: MVNETA_SKB_HEADROOM set last 3 bits to zero")
added headroom alignment check against 8.
Hovewer (if we imagine that NET_SKB_PAD or XDP_PACKET_HEADROOM is not
aligned to cacheline size), it actually aligns headroom down, while
skb/xdp_buff headroom should be *at least* equal to one of the values
(depending on XDP prog presence).
So, fix the check to align the value up. This satisfies both
hardware/driver and network stack requirements.
Fixes: ca23cb0bc50f ("mvneta: MVNETA_SKB_HEADROOM set last 3 bits to zero")
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev(dev) fails, free_netdev(dev) needs
to be called, otherwise a memory leak will occur.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected the MAC_CR configuration bits for 1 GBit operation. The data
sheet allows MAC_CR(2:1) to be 10 and also 11 for 1 GBit/s speed, but
only 10 works correctly.
Devices tested:
Microchip Lan7431, fixed-phy mode
Microchip Lan7430, normal phy mode
Fixes: 6f197fb63850 ("lan743x: Added fixed link and RGMII support")
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sch_generic.h does not need to be included, remove it.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Th referenced change added an extra hw reset to rtl8169_net_suspend()
what makes WoL fail on few chip versions. Therefore skip the extra
reset if we're going down and WoL is enabled.
In rtl_shutdown() rtl8169_hw_reset() is called by rtl8169_net_suspend()
already if needed, therefore avoid issues issue by removing the extra
call. The fix was tested on a system with RTL8168g.
Meanwhile rtl8169_hw_reset() does more than a hw reset and should be
renamed. But that's net-next material.
Fixes: 8ac8e8c64b53 ("r8169: make rtl8169_down central chip quiesce function")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is return PTR_ERR(NULL) which is zero or success. We should
return -ENOMEM instead.
Fixes: 94abdad6974a5 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64_stats mechanism uses sequence counters to protect against 64-bit
values tearing on 32-bit architectures. Updating u64_stats is thus a
sequence counter write side critical section where preemption must be
disabled.
For mdiobus_stats_acct(), disable preemption upon the u64_stats update.
It is called from process context through mdiobus_read() and
mdiobus_write().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bf7afb29d545 ("phy: improve safety of fixed-phy MII register
reading") protected the fixed PHY status with a sequence counter.
Two years later, commit d2b977939b18 ("net: phy: fixed-phy: remove
fixed_phy_update_state()") removed the sequence counter's write side
critical section -- neutralizing its read side retry loop.
Remove the unused seqcount.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the geneve interface is in collect_md (external) mode, it can't send any
packets submitted directly to its net interface, as such packets won't have
metadata attached. This is expected.
However, the kernel itself sends some packets to the interface, most
notably, IPv6 DAD, IPv6 multicast listener reports, etc. This is not wrong,
as tunnel metadata can be specified in routing table (although technically,
that has never worked for IPv6, but hopefully will be fixed eventually) and
then the interface must correctly participate in IPv6 housekeeping.
The problem is that any such attempt increases the tx_error counter. Just
bringing up a geneve interface with IPv6 enabled is enough to see a number
of tx_errors. That causes confusion among users, prompting them to find
a network error where there is none.
Change the counter used to tx_dropped. That better conveys the meaning
(there's nothing wrong going on, just some packets are getting dropped) and
hopefully will make admins panic less.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues with XDP:
1. If the XDP verdict is XDP_ABORTED we break the loop, which results in
us handling one buffer per napi cycle instead of the total budget
(usually 64). To overcome this simply change the xdp_verdict check to
!= XDP_PASS. When the verdict is XDP_PASS, the skb is not expected to
be NULL.
2. Update the residual budget for XDP_DROP and XDP_ABORTED, since
packets are handled in these cases.
Fixes: 548c4940b9f1 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending very high packet rate, the XDP tx queues can get full and
start dropping packets. In this case we don't free the pages which
results in ena driver draining the system memory.
Fix:
Simply free the pages when necessary.
Fixes: 548c4940b9f1 ("net: ena: Implement XDP_TX action")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_uld_in_use() is used only by cxgb4_ktls_det_feature() which
is under CONFIG_CHELSIO_TLS_DEVICE macro.
Fixes: a3ac249a1ab5 ("cxgb4/chcr: Enable ktls settings at run time")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl7WhbkTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXlUnB/0R8dBVSeRfNmyJaadBWKFc/LffwKLD
CQ8PVv22ffkCaEYV2tpnhS6NmkERLNdson4Uo02tVUsjOJ4CrWHTn7aKqYWZyA+O
qv/PiD9TBXJVYMVP2kkyaJlK5KoqeAWBr2kM16tT0cxQmlhE7g0Xo2wU9vhRbU+4
i4F0jffe4lWps65TK392CsPr6UEv1HSel191Py5zLzYqChT+L8WfahmBt3chhsV5
TIUJYQvBwxecFRla7yo+4sUn37ZfcTqD1hCWSr0zs4psW0ge7d80kuaNZS+EqxND
fGm3Bp1BlUuDKsJ/D+AaHLCR47PUZ9t9iMDjZS/ovYglLFwi+h3tAV+W
=LwVR
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v updates from Wei Liu:
- a series from Andrea to support channel reassignment
- a series from Vitaly to clean up Vmbus message handling
- a series from Michael to clean up and augment hyperv-tlfs.h
- patches from Andy to clean up GUID usage in Hyper-V code
- a few other misc patches
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (29 commits)
Drivers: hv: vmbus: Resolve more races involving init_vp_index()
Drivers: hv: vmbus: Resolve race between init_vp_index() and CPU hotplug
vmbus: Replace zero-length array with flexible-array
Driver: hv: vmbus: drop a no long applicable comment
hyper-v: Switch to use UUID types directly
hyper-v: Replace open-coded variant of %*phN specifier
hyper-v: Supply GUID pointer to printf() like functions
hyper-v: Use UUID API for exporting the GUID (part 2)
asm-generic/hyperv: Add definitions for Get/SetVpRegister hypercalls
x86/hyperv: Split hyperv-tlfs.h into arch dependent and independent files
x86/hyperv: Remove HV_PROCESSOR_POWER_STATE #defines
KVM: x86: hyperv: Remove duplicate definitions of Reference TSC Page
drivers: hv: remove redundant assignment to pointer primary_channel
scsi: storvsc: Re-init stor_chns when a channel interrupt is re-assigned
Drivers: hv: vmbus: Introduce the CHANNELMSG_MODIFYCHANNEL message type
Drivers: hv: vmbus: Synchronize init_vp_index() vs. CPU hotplug
Drivers: hv: vmbus: Remove the unused HV_LOCALIZED channel affinity logic
PCI: hv: Prepare hv_compose_msi_msg() for the VMBus-channel-interrupt-to-vCPU reassignment functionality
Drivers: hv: vmbus: Use a spin lock for synchronizing channel scheduling vs. channel removal
hv_utils: Always execute the fcopy and vss callbacks in a tasklet
...
found by smatch:
drivers/net/net_failover.c:65 net_failover_open() error:
we previously assumed 'primary_dev' could be null (see line 43)
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes sense to allow changes to get/set rx flow hash callback only
when rss is enabled. This patch restricts get_rss_hash_opts and
set_rss_hash_opts methods to allow querying and configuring different
Rx flow hash configurations only when rss is enabled
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add support to change TX/RX queue number with "ethtool -L combined".
V5 -> V6: remove check for carrier in hinic_xmit_frame
V4 -> V5: change time zone in patch header
V3 -> V4: update date in patch header
V2 -> V3: remove check for zero channels->combined_count
V1 -> V2: update commit message("ethtool -L" to "ethtool -L combined")
V0 -> V1: remove check for channels->tx_count/rx_count/other_count
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in
the struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
* Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
* Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
* Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
* Fix wrong compatible binding in the qcom driver (Ansuel Smith).
* Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
* Add r8a7742 SoC support to the dt cpufreq driver (Lad Prabhakar).
- Update cpuidle core and drivers:
* Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
* Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
* Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver
and remove an unused local MSR definition from it (Jacob Pan,
Sumeet Pawnikar).
- Update devfreq core and drivers:
* Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
* Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
* Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei).
-----BEGIN PGP SIGNATURE-----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=APdj
-----END PGP SIGNATURE-----
Merge tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the system-wide PM driver flags, make runtime switching
of cpuidle governors easier, improve the user space hibernation
interface code, add intel-speed-select interface documentation, add
more debug messages to the ACPI code handling suspend to idle, update
the cpufreq core and drivers, fix a minor issue in the cpuidle core
and update two cpuidle drivers, improve the PM-runtime framework,
update the Intel RAPL power capping driver, update devfreq core and
drivers, and clean up the cpupower utility.
Specifics:
- Rework the system-wide PM driver flags to make them easier to
understand and use and update their documentation (Rafael Wysocki,
Alan Stern).
- Allow cpuidle governors to be switched at run time regardless of
the kernel configuration and update the related documentation
accordingly (Hanjun Guo).
- Improve the resume device handling in the user space hibernarion
interface code (Domenico Andreoli).
- Document the intel-speed-select sysfs interface (Srinivas
Pandruvada).
- Make the ACPI code handing suspend to idle print more debug
messages to help diagnose issues with it (Rafael Wysocki).
- Fix a helper routine in the cpufreq core and correct a typo in the
struct cpufreq_driver kerneldoc comment (Rafael Wysocki, Wang
Wenhu).
- Update cpufreq drivers:
- Make the intel_pstate driver start in the passive mode by
default on systems without HWP (Rafael Wysocki).
- Add i.MX7ULP support to the imx-cpufreq-dt driver and add
i.MX7ULP to the cpufreq-dt-platdev blacklist (Peng Fan).
- Convert the qoriq cpufreq driver to a platform one, make the
platform code create a suitable device object for it and add
platform dependencies to it (Mian Yousaf Kaukab, Geert
Uytterhoeven).
- Fix wrong compatible binding in the qcom driver (Ansuel Smith).
- Build the omap driver by default for ARCH_OMAP2PLUS (Anders
Roxell).
- Add r8a7742 SoC support to the dt cpufreq driver (Lad
Prabhakar).
- Update cpuidle core and drivers:
- Fix three reference count leaks in error code paths in the
cpuidle core (Qiushi Wu).
- Convert Qualcomm SPM to a generic cpuidle driver (Stephan
Gerhold).
- Fix up the execution order when entering a domain idle state in
the PSCI driver (Ulf Hansson).
- Fix a reference counting issue related to clock management and
clean up two oddities in the PM-runtime framework (Rafael Wysocki,
Andy Shevchenko).
- Add ElkhartLake support to the Intel RAPL power capping driver and
remove an unused local MSR definition from it (Jacob Pan, Sumeet
Pawnikar).
- Update devfreq core and drivers:
- Replace strncpy() with strscpy() in the devfreq core and use
lockdep asserts instead of manual checks for a locked mutex in
it (Dmitry Osipenko, Krzysztof Kozlowski).
- Add a generic imx bus scaling driver and make it register an
interconnect device (Leonard Crestez, Gustavo A. R. Silva).
- Make the cpufreq notifier in the tegra30 driver take boosting
into account and delete an unuseful error message from that
driver (Dmitry Osipenko, Markus Elfring).
- Remove unneeded semicolon from the cpupower code (Zou Wei)"
* tag 'pm-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (51 commits)
cpuidle: Fix three reference count leaks
PM: runtime: Replace pm_runtime_callbacks_present()
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
PM: hibernate: Restrict writes to the resume device
PM: runtime: clk: Fix clk_pm_runtime_get() error path
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
ACPI: EC: PM: s2idle: Extend GPE dispatching debug message
ACPI: PM: s2idle: Print type of wakeup debug messages
powercap: RAPL: remove unused local MSR define
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
Documentation: admin-guide: pm: Document intel-speed-select
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
Documentation: ABI: make current_governer_ro as a candidate for removal
...
- Enable erase/discard/trim support for all (e)MMC/SD hosts
- Export information through sysfs about enhanced RPMB support (eMMC v5.1+)
- Align the initialization commands for SDIO cards
- Fix SDIO initialization to prevent memory leaks and NULL pointer errors
- Do not export undefined MMC_NAME/MODALIAS for SDIO cards
- Export device/vendor field from common CIS for SDIO cards
- Move SDIO IDs from functional drivers to the common SDIO header
- Introduce the ->request_atomic() host ops
MMC host:
- Improve support for HW busy signaling for several hosts
- Converting some DT bindings to the json-schema
- meson-mx-sdhc: Add driver and DT doc for the Amlogic Meson SDHC controller
- meson-mx-sdio: Run a soft reset to recover from timeout/CRC error
- mmci: Convert to use mmc_regulator_set_vqmmc()
- mmci_stm32_sdmmc: Fix a couple of DMA bugs
- mmci_stm32_sdmmc: Fix power on issue
- renesas,mmcif,sdhci: Document r8a7742 DT bindings
- renesas_sdhi: Add support for M3-W ES1.2 and 1.3 revisions
- renesas_sdhi: Improvements to the TAP selection
- renesas_sdhi/tmio: Further fixup runtime PM management at ->remove()
- sdhci: Introduce ops to dump vendor specific registers
- sdhci-cadence: Fix PHY write sequence
- sdhci-esdhc-imx: Improve tunings
- sdhci-esdhc-imx: Enable GPIO card detect as system wakeup
- sdhci-esdhc-imx: Add HS400 support for i.MX6SLL
- sdhci-esdhc-mcf: Add driver for the Coldfire/M5441X esdhc controller
- m68k: mcf5441x: Add platform data to enable esdhc mmc controller
- sdhci-msm: Improve HS400 tuning
- sdhci-msm: Dump vendor specific registers at error
- sdhci-msm: Add support for DLL/DDR properties provided from DT
- sdhci-msm: Add support for the sm8250 variant
- sdhci-msm: Add support for DVFS by converting to dev_pm_opp_set_rate()
- sdhci-of-arasan: Add support for Intel Keem Bay variant
- sdhci-of-arasan: Add support for Xilinx Versal SD variant
- sdhci-of-dwcmshc: Add support for system suspend/resume
- sdhci-of-dwcmshc: Fix UHS signaling support
- sdhci-of-esdhc: Fix tuning for eMMC HS400 mode
- sdhci-pci-gli: Add Genesys Logic GL9763E support
- sdhci-sprd: Add support for the ->request_atomic() ops
- sdhci-tegra: Avoid reading autocal timeout values when not applicable
MEMSTICK:
- Minor trivial update.
-----BEGIN PGP SIGNATURE-----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=1bkc
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Enable erase/discard/trim support for all (e)MMC/SD hosts
- Export information through sysfs about enhanced RPMB support (eMMC v5.1+)
- Align the initialization commands for SDIO cards
- Fix SDIO initialization to prevent memory leaks and NULL pointer errors
- Do not export undefined MMC_NAME/MODALIAS for SDIO cards
- Export device/vendor field from common CIS for SDIO cards
- Move SDIO IDs from functional drivers to the common SDIO header
- Introduce the ->request_atomic() host ops
MMC host:
- Improve support for HW busy signaling for several hosts
- Converting some DT bindings to the json-schema
- meson-mx-sdhc: Add driver and DT doc for the Amlogic Meson SDHC controller
- meson-mx-sdio: Run a soft reset to recover from timeout/CRC error
- mmci: Convert to use mmc_regulator_set_vqmmc()
- mmci_stm32_sdmmc: Fix a couple of DMA bugs
- mmci_stm32_sdmmc: Fix power on issue
- renesas,mmcif,sdhci: Document r8a7742 DT bindings
- renesas_sdhi: Add support for M3-W ES1.2 and 1.3 revisions
- renesas_sdhi: Improvements to the TAP selection
- renesas_sdhi/tmio: Further fixup runtime PM management at ->remove()
- sdhci: Introduce ops to dump vendor specific registers
- sdhci-cadence: Fix PHY write sequence
- sdhci-esdhc-imx: Improve tunings
- sdhci-esdhc-imx: Enable GPIO card detect as system wakeup
- sdhci-esdhc-imx: Add HS400 support for i.MX6SLL
- sdhci-esdhc-mcf: Add driver for the Coldfire/M5441X esdhc controller
- m68k: mcf5441x: Add platform data to enable esdhc mmc controller
- sdhci-msm: Improve HS400 tuning
- sdhci-msm: Dump vendor specific registers at error
- sdhci-msm: Add support for DLL/DDR properties provided from DT
- sdhci-msm: Add support for the sm8250 variant
- sdhci-msm: Add support for DVFS by converting to dev_pm_opp_set_rate()
- sdhci-of-arasan: Add support for Intel Keem Bay variant
- sdhci-of-arasan: Add support for Xilinx Versal SD variant
- sdhci-of-dwcmshc: Add support for system suspend/resume
- sdhci-of-dwcmshc: Fix UHS signaling support
- sdhci-of-esdhc: Fix tuning for eMMC HS400 mode
- sdhci-pci-gli: Add Genesys Logic GL9763E support
- sdhci-sprd: Add support for the ->request_atomic() ops
- sdhci-tegra: Avoid reading autocal timeout values when not applicable
MEMSTICK:
- Minor trivial update"
* tag 'mmc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (127 commits)
dt-bindings: mmc: Convert sdhci-pxa to json-schema
mmc: sdhci-msm: Clear tuning done flag while hs400 tuning
mmc: core: Export device/vendor ids from Common CIS for SDIO cards
mmc: core: Do not export MMC_NAME= and MODALIAS=mmc:block for SDIO cards
mmc: sdhci-of-at91: fix CALCR register being rewritten
mmc: sdhci-esdhc-imx: disable the CMD CRC check for standard tuning
mmc: sdhci-esdhc-imx: fix the mask for tuning start point
mmc: host: sdhci-esdhc-imx: add wakeup feature for GPIO CD pin
mmc: mmci_sdmmc: fix DMA API warning max segment size
mmc: mmci_sdmmc: fix DMA API warning overlapping mappings
mmc: sdhci-of-arasan: Add support for Intel Keem Bay
dt-bindings: mmc: arasan: Add compatible strings for Intel Keem Bay
mmc: sdhci-cadence: fix PHY write
mmc: sdio: Sort all SDIO IDs in common include file
mmc: sdio: Fix Cypress SDIO IDs macros in common include file
mmc: sdio: Move SDIO IDs from b43-sdio driver to common include file
mmc: sdio: Move SDIO IDs from ath10k driver to common include file
mmc: sdio: Move SDIO IDs from ath6kl driver to common include file
mmc: sdio: Move SDIO IDs from smssdio driver to common include file
mmc: sdio: Move SDIO IDs from btmtksdio driver to common include file
...
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-06-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 55 non-merge commits during the last 1 day(s) which contain
a total of 91 files changed, 4986 insertions(+), 463 deletions(-).
The main changes are:
1) Add rx_queue_mapping to bpf_sock from Amritha.
2) Add BPF ring buffer, from Andrii.
3) Attach and run programs through devmap, from David.
4) Allow SO_BINDTODEVICE opt in bpf_setsockopt, from Ferenc.
5) link based flow_dissector, from Jakub.
6) Use tracing helpers for lsm programs, from Jiri.
7) Several sk_msg fixes and extensions, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports a warning at efx_ef10_try_update_nic_stats_vf()
warning: context imbalance in efx_ef10_try_update_nic_stats_vf()
- unexpected unlock
The root cause is the missing annotation at
efx_ef10_try_update_nic_stats_vf()
Add the missing _must_hold(&efx->stats_lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current design enables ktls setting from start, which is not
efficient. Now the feature will be enabled when user demands
TLS offload on any interface.
v1->v2:
- taking ULD module refcount till any single connection exists.
- taking rtnl_lock() before clearing tls_devops.
v2->v3:
- cxgb4 is now registering to tlsdev_ops.
- module refcount inc/dec in chcr.
- refcount is only for connections.
- removed new code from cxgb_set_feature().
v3->v4:
- fixed warning message.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-31
This series contains updates to the ice driver only.
Brett modifies the driver to allow users to clear a VF's
administratively set MAC address on the PF. Fixes the driver to
recognize an existing VLAN tag when DMAC/SMAC is enabled in a packet.
Fixes an issue, so that VF's are reset after any VF port VLAN
modifications are made on the PF. Made sure the register QRXFLXP_CNTXT
is cleared before writing a new value to ensure the previous value is
not passed forward. Updates the PF to allow the VF to request a reset
as soon as it has been initialized. Fixes an issue to ensure when a VSI
is created, it uses the current coalesce value, not the default value.
Paul allows untrusted VF's to add 16 filters.
Dan increases the timeout needed after a PFR to allow ample time for
package download.
Chinh adjust the define value for the number of PHY speeds we currently
support. Changes the driver to ignore EMODE error when configuring the
PHY.
Jesse fixes an issue which was preventing a user from configuring the
interface before bringing it up.
Henry fixes the logic for adding back perfect flows after flow director
filter does a deletion.
Bruce fixes line wrappings to make it more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fix dereference of nexthop group in fdb nexthop group
update validation path.
Fixes: 1274e1cc4226 ("vxlan: ecmp support for mac fdb entries")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.
Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.
With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.
Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class. This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.
Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.
Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't export __bcm_phy_enable_rdb_access() and
__bcm_phy_enable_legacy_access() functions. They aren't used outside this
module and it was forgotten to provide a prototype for these functions.
Just make them static for now.
Fixes: 11ecf8c55b91 ("net: phy: broadcom: add cable test support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tun in IFF_NAPI_FRAGS mode calls napi_gro_frags. Unlike netif_rx and
netif_gro_receive, this expects skb->data to point to the mac layer.
But skb_probe_transport_header, __skb_get_hash_symmetric, and
xdp_do_generic in tun_get_user need skb->data to point to the network
header. Flow dissection also needs skb->protocol set, so
eth_type_trans has to be called.
Ensure the link layer header lies in linear as eth_type_trans pulls
ETH_HLEN. Then take the same code paths for frags as for not frags.
Push the link layer header back just before calling napi_gro_frags.
By pulling up to ETH_HLEN from frag0 into linear, this disables the
frag0 optimization in the special case when IFF_NAPI_FRAGS is used
with zero length iov[0] (and thus empty skb->linear).
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Petar Penkov <ppenkov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value adapter->rss_conf is stored in DMA memory, and it is assigned
to rssConf, so rssConf->indTableSize can be modified at anytime by
malicious hardware. Because rssConf->indTableSize is assigned to n,
buffer overflow may occur when the code "rssConf->indTable[n]" is
executed.
To fix this possible bug, n is checked after being used.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.
A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:
1. Packets might not need to be marked with 'offload_fwd_mark'. For
example, if packet was trapped before L2 forwarding
2. Packets might not need to be injected to the kernel's Rx path. For
example, sampled packets are reported to user space via the psample
module
Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register two control traps with devlink. The existing selftest at
tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh iterates
over all registered traps and checks that the action of non-drop traps
cannot be changed. Up until now only exception traps were tested, now
control traps will be tested as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
