IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
As per the specification of DPU_CTL_ACTIVE_CFG the configuration of
active blocks should be proactively specified, and the pingpong block is
no different.
The downstream display driver [1] confirms this by also calling
bind_pingpong_blk on CTL_ACTIVE_CFG. Note that this else-if is always
entered, as setup_intf_cfg - unlike this mainline dpu driver that
combines both behind the same function pointer - is left NULL in favour
of using setup_intf_cfg_v1 when CTL_ACTIVE_CFG is set.
This solves continuous timeouts on at least the Qualcomm sm6125 SoC:
[drm:dpu_encoder_frame_done_timeout:2091] [dpu error]enc31 frame done timeout
[drm:_dpu_encoder_phys_cmd_handle_ppdone_timeout.isra.0] *ERROR* id:31 pp:0 kickoff timeout 0 cnt 1 koff_cnt 1
[drm:dpu_encoder_phys_cmd_prepare_for_kickoff] *ERROR* failed wait_for_idle: id:31 ret:-110 pp:0
In the same way this pingpong block should also be unbound followed by
an interface flush when the encoder is disabled, according to the
downstream display driver [2].
[1]: https://source.codeaurora.org/quic/la/platform/vendor/opensource/display-drivers/tree/msm/sde/sde_encoder_phys_cmd.c?h=LA.UM.9.16.r1-08500-MANNAR.0#n167
[2]: https://source.codeaurora.org/quic/la/platform/vendor/opensource/display-drivers/tree/msm/sde/sde_encoder.c?h=LA.UM.9.16.r1-08500-MANNAR.0#n2986
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/475874/
Link: https://lore.kernel.org/r/20220223114011.219044-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To remove possible confusion between (old) INTF_EDP and newer INTF_DP,
stop using INTF_EDP in DPU's code. Until the 8x74/8x84 SoCs are
supported by DPU driver, there is no point in using INTF_EDP.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/475560/
Link: https://lore.kernel.org/r/20220222062246.242577-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU driver never supported INTF_EDP, so let's drop the obsolete comment.
If at some point 8x74/8x84's INTF_EDP is ported to DPU driver,
corresponding handling will have to be ported too. Until that time, the
comment serves no purpose.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/475557/
Link: https://lore.kernel.org/r/20220222062246.242577-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This enum value does not correspond to any of actual interface types,
it's not used by the driver, and the value of INTF_WB is greater than
INTF_TYPE_MAX. Thus this symbol serves no purpose and can be removed.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/475556/
Link: https://lore.kernel.org/r/20220222062246.242577-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Based on the discussions on the mailing list, document enum
dpu_intf_type and it's controversial fields: INTF_DP and INTF_EDP.
INTF_EDP is used for older eDP interface found on msm8x74/msm8x84
INTF_DP is used for both eDP and DP interfaces handled by the msm/dp
driver. The DPU driver does not make a difference between them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/475555/
Link: https://lore.kernel.org/r/20220222062246.242577-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove additional indirection: specify IRQ callbacks and IRQ indices
directly rather than through the pointer in the irq structure. For each
IRQ we have a constant IRQ callback. This change simplifies code review
as the reader no longer needs to remember which function is called.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474700/
Link: https://lore.kernel.org/r/20220217043148.480898-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU interrupts code allows multiple callbacks per interrut. In reality
none of the interrupts is shared between blocks (and will probably never
be). Drop support for registering multiple callbacks per interrupt to
simplify interrupt handling code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/474701/
Link: https://lore.kernel.org/r/20220217043148.480898-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Smatch reports this issue
msm_ringbuffer.c:43:36: warning: symbol 'msm_sched_ops' was not declared. Should it be static?
msm_sched_ops is only used in msm_ringbuffer.c so change its
storage-class specifier to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482883/
Link: https://lore.kernel.org/r/20220421131507.1557667-1-trix@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove unused MSM_DISPLAY_CAP_HOT_PLUG and MSM_DISPLAY_CAP_EDID
macros from msm_drv.h.
Even if we need these, there are drm equivalent ones present.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/482260/
Link: https://lore.kernel.org/r/1650049782-8421-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When DSC is enabled, we need to configure DSI registers accordingly and
configure the respective stream compression registers.
Add support to calculate the register setting based on DSC params and
timing information and configure these registers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480934/
Link: https://lore.kernel.org/r/20220406094031.1027376-15-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add a mode valid callback for dsi_mgr for checking mode being valid in
case of DSC. For DSC the height and width needs to be multiple of slice,
so we check that here
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480930/
Link: https://lore.kernel.org/r/20220406094031.1027376-13-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
For DSC to work we typically need a 2,2,1 configuration. This should
suffice for resolutions up to 4k. For more resolutions like 8k this won't
work.
Also, it is better to use 2 LMs and DSC instances as half width results
in lesser power consumption as compared to single LM, DSC at full width.
The panel has been tested only with 2,2,1 configuration, so for
now we blindly create 2,2,1 topology when DSC is enabled
Co-developed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480925/
Link: https://lore.kernel.org/r/20220406094031.1027376-11-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU supports different topologies for the case when multiple INTFs are
being driven by the single phys_enc. The driver defaults to using 3DMux
in such cases. Don't use it if DSC merge is used instead.
Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/480922/
Link: https://lore.kernel.org/r/20220406094031.1027376-9-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We need to configure the encoder for DSC configuration and calculate DSC
parameters for the given timing so this patch adds that support by
adding dpu_encoder_prep_dsc() which is invoked when DSC is enabled.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480920/
Link: https://lore.kernel.org/r/20220406094031.1027376-8-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Later gens of hardware have DSC bits moved to hw_ctl, so configure these
bits so that DSC would work there as well
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480918/
Link: https://lore.kernel.org/r/20220406094031.1027376-7-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In SDM845, DSC can be enabled by writing to pingpong block registers, so
add support for DSC in hw_pp
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480914/
Link: https://lore.kernel.org/r/20220406094031.1027376-5-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When DSC is enabled, we need to get the DSC parameters from the panel
driver, so add a dsc parameter in panel to fetch and pass DSC
configuration for DSI panels to DPU encoder, which will enable and
then configure DSC hardware blocks accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480910/
Link: https://lore.kernel.org/r/20220406094031.1027376-3-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
Timing engine provides driving force for this purpose. This patch base
on HPG (Hardware Programming Guide) to revise timing engine register
setting to accommodate both widebus and non widebus application. Also
horizontal width parameters need to be reduced by half since two pixel
data are clocked out per pixel clock when widebus feature enabled.
Widebus can be enabled individually at DP. However at DSI, widebus have
to be enabled along with DSC to achieve pixel clock rate be scaled down
with same ratio as compression ratio when 10 bits per source component.
Therefore this patch add no supports of DSI related widebus and compression.
Changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
Changes in v4:
-- rework timing engine to not interfere with dsi/hdmi
-- cover both widebus and compression
Changes in v5:
-- remove supports of DSI widebus and compression
Changes in v7:
-- split this patch into 3 patches
-- add Tested-by
Changes in v8:
-- move new registers writes under DATA_HCTL_EN features check.
Changes in v10:
-- add const inside dpu_encoder_is_widebus_enabled()
-- drop useless parenthesis please
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476281/
Link: https://lore.kernel.org/r/1645824192-29670-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The “DP timing” requires the active region to be defined in the
bottom-right corner of the frame dimensions which is different
with DSI. Therefore both display_h_end and display_v_end need
to be adjusted accordingly. However current implementation has
only display_h_end adjusted.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Fixes: fc3a69ec68d3 ("drm/msm/dpu: intf timing path for displayport")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/476277/
Link: https://lore.kernel.org/r/1645824192-29670-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove unused field plane_property from struct msm_drm_private. Also
drop the enum msm_mdp_plane_property which also becomes unused.
Fixes: 7d36db0be3b9 ("drm/msm/mdp5: switch to standard zpos property")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/480939/
Link: https://lore.kernel.org/r/20220406100556.479706-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove manual removal of DRM modesetting objects, it is done anyway by
the drm_mode_config_cleanup() called from msm_drm_uninit(). Other
MSM display drivers (MDP4, MDP5) do not manually destroy objects and
trust generic code to do it's work.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/480943/
Link: https://lore.kernel.org/r/20220406101247.483649-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add calls to drm_bridge_add()/drm_bridge_remove() DRM bridges created by
the driver. This fixes the following warning.
WARNING: CPU: 0 PID: 1 at kernel/locking/mutex.c:579 __mutex_lock+0x840/0x9f4
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc1-00002-g3054695a0d27-dirty #55
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0xc8/0x1e8
__warn from warn_slowpath_fmt+0x78/0xa8
warn_slowpath_fmt from __mutex_lock+0x840/0x9f4
__mutex_lock from mutex_lock_nested+0x1c/0x24
mutex_lock_nested from drm_bridge_hpd_enable+0x2c/0x84
drm_bridge_hpd_enable from msm_hdmi_modeset_init+0xc0/0x21c
msm_hdmi_modeset_init from mdp4_kms_init+0x53c/0x90c
mdp4_kms_init from msm_drm_bind+0x514/0x698
msm_drm_bind from try_to_bring_up_aggregate_device+0x160/0x1bc
try_to_bring_up_aggregate_device from component_master_add_with_match+0xc4/0xf8
component_master_add_with_match from msm_pdev_probe+0x274/0x350
msm_pdev_probe from platform_probe+0x5c/0xbc
platform_probe from really_probe.part.0+0x9c/0x290
really_probe.part.0 from __driver_probe_device+0xa8/0x13c
__driver_probe_device from driver_probe_device+0x34/0x10c
driver_probe_device from __driver_attach+0xbc/0x178
__driver_attach from bus_for_each_dev+0x74/0xc0
bus_for_each_dev from bus_add_driver+0x160/0x1e4
bus_add_driver from driver_register+0x88/0x118
driver_register from do_one_initcall+0x6c/0x334
do_one_initcall from kernel_init_freeable+0x1bc/0x220
kernel_init_freeable from kernel_init+0x18/0x12c
kernel_init from ret_from_fork+0x14/0x2c
Fixes: 3d3f8b1f8b62 ("drm/bridge: make bridge registration independent of drm flow")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/481778/
Link: https://lore.kernel.org/r/20220411234953.2425280-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The msm_mdss serves several roles at this moment. It provides IRQ domain
used by MDP5 and DPU drivers but it also serves as a component master
for both those usecases. MDP4 (which does not have separate MDSS device)
is the component master on it's own.
Remove this assymmetry and make both MDP5 and DPU component masters too.
This removes a need to care about drm/components from msm_mdss driver,
removes an mdss pointer from struct msm_drm_private and simplifies the
interface between mdp5/dpu and msm_drv.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482512/
Link: https://lore.kernel.org/r/20220419155346.1272627-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MSM DRM driver already allows one to compile out the DP or DSI support.
Add support for disabling other features like MDP4/MDP5/DPU drivers or
direct HDMI output support.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482508/
Link: https://lore.kernel.org/r/20220419155346.1272627-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Let's make the match's data pointer a (sub-)driver's private data. The
only user currently is the msm_drm_init() function, using this data to
select kms_init callback. Pass this callback through the driver's
private data instead.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482510/
Link: https://lore.kernel.org/r/20220419155346.1272627-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently the msm platform driver is a multiplex handling several cases:
- headless GPU-only driver,
- MDP4 with flat device nodes,
- MDP5/DPU MDSS with all the nodes being children of MDSS node.
This results in not-so-perfect code, checking the hardware version
(MDP4/MDP5/DPU) in several places, checking for mdss even when it can
not exist, etc. Split the code into three handling subdrivers (mdp4,
mdss and headless msm).
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482507/
Link: https://lore.kernel.org/r/20220419155346.1272627-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since now there is just one mdss subdriver, drop all the indirection,
make msm_mdss struct completely opaque (and defined inside msm_mdss.c)
and call mdss functions directly.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482505/
Link: https://lore.kernel.org/r/20220419155346.1272627-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MDP5 and DPU1 both provide the driver handling the MDSS region, which
handles the irq domain and (incase of DPU1) adds some init for the UBWC
controller. Unify those two pieces of code into a common driver.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/482506/
Link: https://lore.kernel.org/r/20220419155346.1272627-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
simple_ondemand interacts poorly with clamp_to_idle. It only looks at
the load since the last get_dev_status call, while it should really look
at the load over polling_ms. When clamp_to_idle true, it almost always
picks the lowest frequency on active because the gpu is idle between
msm_devfreq_idle/msm_devfreq_active.
This logic could potentially be moved into devfreq core.
Fixes: 7c0ffcd40b16 ("drm/msm/gpu: Respect PM QoS constraints")
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220416003314.59211-3-olvaffe@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move tracking and busy time calculation to msm_devfreq_get_dev_status.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220416003314.59211-2-olvaffe@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
It is redundant since commit 7c0ffcd40b16 ("drm/msm/gpu: Respect PM QoS
constraints") because dev_pm_qos_update_request triggers get_dev_status.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220416003314.59211-1-olvaffe@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The motivation at this point is mainly native userspace mesa driver in a
VM guest. The one remaining synchronous "hotpath" is buffer allocation,
because guest needs to wait to know the bo's iova before it can start
emitting cmdstream/state that references the new bo. By allocating the
iova in the guest userspace, we no longer need to wait for a response
from the host, but can just rely on the allocation request being
processed before the cmdstream submission. Allocation failures (OoM,
etc) would just be treated as context-lost (ie. GL_GUILTY_CONTEXT_RESET)
or subsequent allocations (or readpix, etc) can raise GL_OUT_OF_MEMORY.
v2: Fix inuse check
v3: Change mismatched iova case to -EBUSY
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220411215849.297838-11-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
With userspace allocated iova (next patch), we can have a race condition
where userspace observes the fence completion and deletes the vma before
retire_submit() gets around to unpinning the vma. To handle this, add a
fenced unpin which drops the refcount but tracks the fence, and update
msm_gem_vma_inuse() to check any previously unsignaled fences.
v2: Fix inuse underflow (duplicate unpin)
v3: Fix msm_job_run() vs submit_cleanup() race condition
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220411215849.297838-10-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Combines duplicate vma lookup in the get_and_pin path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220411215849.297838-8-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
