IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
mlxsw does not support VXLAN devices with a physical device attached and
vetoes such configurations upon enslavement to an offloaded bridge.
Commit 0ce1822c2a08 ("vxlan: add adjacent link to limit depth level")
changed the VXLAN device to be an upper of the physical device which
causes mlxsw to veto the creation of the VXLAN device with "Unknown
upper device type".
This is OK as this configuration is not supported, but it prevents us
from testing bad flows involving the enslavement of VXLAN devices with a
physical device to a bridge, regardless if the physical device is an
mlxsw netdev or not.
Adjust the test to use a dummy device as a physical device instead of a
mlxsw netdev.
Fixes: 0ce1822c2a08 ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.
The above did not matter much until commit b5ce611fd96e ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.
Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.
Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.
Fixes: b5ce611fd96e ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test generic devlink-trap functionality over mlxsw. These tests are not
specific to a single trap, but do not check the devlink-trap common
infrastructure either.
Currently, the only test case is device deletion (by reloading the
driver) while packets are being trapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases for devlink-trap on top of the netdevsim implementation.
The tests focus on the devlink-trap core infrastructure and user space
API. They test both good and bad flows and also dismantle of the netdev
and devlink device used to report trapped packets.
This allows device drivers to focus their tests on device-specific
functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test netdevsim devlink region implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test recently added netdevsim devlink param implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dedfde2fe1c4 ("mlxsw: spectrum_dcb: Configure DSCP map as the last
rule is removed") fixed a problem in mlxsw where last DSCP rule to be
removed remained in effect when DSCP rewrite was applied.
Add a selftest that covers this problem.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two tests have some problems in the global scope pollution and on
contrary, contain unnecessary local declarations. Fix them.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some spelling typo in qos_mc_aware.sh
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the offload indication for unicast routes is correctly set in
different scenarios. IPv4 support will be added in the future.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that IPv4 and IPv6 nexthops are correctly marked with offload
indication in response to neighbour events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilizes the devlink flash code.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that neighbour entries are marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when strict priority is configured on a system, the
higher-priority traffic does actually win all the available bandwidth.
The test uses a similar approach to qos_mc_aware.sh to run and account
the traffic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract reusable code from qos_mc_aware.sh and put into a new library.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test runs two streams of traffic from two independent ports to
create congestion on one egress port. It is necessary to configure the
shared buffer thresholds correctly, to make sure that there is traffic
from both streams in the shared buffer. Only then can the test actually
test prioritization among these streams.
Without this configuration, it is possible, that one of the streams
takes all of port-pool quota, and the other stream is not even admitted,
thus invalidating the result.
On Spectrum-1, this is not a problem, because MC traffic uses a separate
pool. But for Spectrum-2, MC and UC share the same pool, and the correct
configuration is important.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do insertions and removal of filters during rehash in higher volumes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking of newly added trace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints. Use IPv6 addresses.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh 2 times and make the script work with ifnames
passed on the command line.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. This
traffic is seen at the counters, and causes spurious failures.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the bug is fixed and we no longer have C-TCAM spill for two
keys that differ only in delta.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent fix in C-TCAM spillage for delta masks, the test stops to be
falsely positive. So fix it not to use delta by adding src_ip bits to the
masks. Alongside with that, use C-TCAM spill trace to see when the
spillage actually happens.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to specify number of trace hits and move helpers
to the beginning of the file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that externally learned FDB entries added from user space are
marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw doesn't implement offloading of all types of FDB entries that the
VXLAN driver supports. Test that such FDB entries are rejected. That
makes sure that the decision made by the existing validation code in
mlxsw propagates up the stack. It also exercises rollback functionality
in VXLAN, and tests that extack is returned.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test case for the issue fixed by previous commit. In case the
offloading of an unsupported VxLAN tunnel was triggered by adding the
mapped VLAN to a local port, then error should be returned to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch added the ability to offload a VXLAN tunnel used for L3
VNI when it is present in the VLAN-aware bridge before the corresponding
VLAN interface is configured. This patch adds a test case to verify
that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new test that is focused on rtnetlink configuration. Its purpose
is to test valid and invalid (as deemed by mlxsw) configurations and
make sure that they succeed / fail without producing a trace.
Some of the test cases are derived from recent fixes in order to make
sure that the fixed bugs are not introduced again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eRP table is active when there is more than a single rule
pattern. It may be that the patterns are close enough and use delta
mechanism. Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} where the rule delta bits must be
cleared.
Add a test that exercises Bloom filter with delta mechanism.
Configure rules within delta range and pass a packet which is
supposed to hit the correct rule.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} and the computation also varies
according to the region key size.
Add a test that exercises the possible combinations by creating
multiple chains using different key sizes and then pass a frame that
is supposed to to produce a hit on all of the regions.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that exercises Bloom filter code.
Activate eRP table in the region by adding multiple rule patterns which
with very high probability use different entries in the Bloom filter.
Then send packets in order to check lookup hits on all relevant rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FID RIF is created for a bridge with IP address, its MAC address
must obey the same requirements as other RIFs. Test that attempts to
change the address incompatibly by attaching a device are vetoed with
extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that attempts to change address in a way that violates Spectrum
requirements are vetoed with extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test mapping a VLAN at a port device such that on the same VLAN, there
already is an unoffloadable VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test mapping a VLAN at a VXLAN device that can't be offloaded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VXLAN device is attached to an offloaded bridge, or when a
front-panel port is attached to a bridge that already has a VXLAN
device, mlxsw should offload the existing offloadable FDB entries.
Similarly when VXLAN device is downed, the FDB entries are unoffloaded,
and the marks thus need to be cleared. Similarly when a front-panel port
device is attached to a bridge with a VXLAN device, or when VLAN flags
are tweaked on a VXLAN port attached to a VLAN-aware bridge.
Test that the replaying / clearing logic works by observing transitions
in presence of offload marks under different scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a testsuite dedicated to testing extack propagation and related
functionality.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Construct a "one-armed router" topology and test that packets are
forwarded by the ASIC and that a copy of the packet is sent to the
kernel, which does not forward the packet again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the existing VLAN-unaware tests with their VLAN-aware
counterparts. This includes sanitization of invalid configuration and
offload indication on the local route performing decapsulation and the
FDB entries perform encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
