IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Over-current reporting isn't supported on some platforms such as bcm63xx.
These devices will incorrectly report over-current if this flag isn't properly
activated.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-4-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an ignore_oc flag which can be set by EHCI controller
not supporting or wanting to disable overcurrent checking. The EHCI
platform data in include/linux/usb/ehci_pdriver.h is also augmented to
take advantage of this new flag.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223174455.1378-2-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've confirmed that both the ASMedia ASM1042A and ASM3242 have the same
problem as the ASM1142 and ASM2142/ASM3142, where they lose some of the
upper bits of 64-bit DMA addresses. As with the other chips, this can
cause problems on systems where the upper bits matter, and adding the
XHCI_NO_64BIT_SUPPORT quirk completely fixes the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501aa ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501aa ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the LS/FS device is connected to an external HS hub, the member
@tt_info in xhci_virt_device struct in not NULL, use it to check
whether a LS/FS device is under an exernal HS hub, then no need get
the slot context of this device.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/8117df52f16bd03087e486d7d740a183b6dd634a.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."
Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/5b9ff09f53d23cf9e5c5437db4ffc18b798bf60c.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the USB headset is plug into an external hub, sometimes
can't set config due to not enough bandwidth, so need improve
LS/FS INT/ISOC bandwidth scheduling with TT.
Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yaqii Wu <yaqii.wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/2f30e81400a59afef5f8231c98149169c7520519.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Side effect may happen if use or operator to set schedule parameters
when the parameters are already set before. Set them directly due to
other bits are reserved.
Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/d287899e6beb2fc1bfb8900c75a872f628ecde55.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
And, no one noticed that a __maybe_unused dentry * in uhci_start()
really was unused, so remove that as it's obviously not needed, and
hasn't been for quite some time.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep the dentry pointer around for the created
debugfs file, as it is only needed when removing it from the system.
When it is to be removed, ask debugfs itself for the pointer, to save on
storage and make things a bit simpler.
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20210216144645.3813043-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuNNh8scc2k/wOAE+9OeQG+StrGQFAmAzrfYACgkQ9OeQG+St
rGTmRQ/+MG9BO1WahlXZ9eVx6n6KmtwlzAy5m4B24GomvcXsa+T2s0Vs43hAsOQ2
f/b6n1mPlwRjAvKW8IfO243HKDE6STGbtVPae6ts586QCODs8i3MQsq4SWmM/DMk
TR87hTo1zd4baVT9tkM8/UdUwQjr0yRf4ZDhcCj09tMClnV/8ZAEE9/lLkBpDoer
wcuPaDtRfJhN+Pqnm8ES8KPj15nVm/GFWBFoDWZIOCjyDnl8Y/1Bnz3NeqzfwM1o
O0NS/9a1tMBn7TNGkkcJCimqOLZS2OgxLND8fie0rC5fmwzVomKXE24OdXpSQCps
LiGJr+iQOaX6qNqJY2h1If8F+RPwKfh4Mrk12x0MWB6Ap2iKsQ6bmtUCNatmJ4PG
5iKV5zY0SwKRYXAkXcNosEPUJqZirFHJCzrQ8IBmiSJ1cahZykWFgorDnA97kNLR
Wlp2Y/037ug7EGZ0YSaXvbpuMyyjDP4TBKqBiSl7a90QYoXQg2QgcrBO3kVlh/5H
Dxq9URvIpDLIGo1EUBU90kB54TUeDhJVHJWDfXNwOp4dP1Xm6b2w+d86GnUQanlC
sinRut1ULMyitmIzg9F74MZKaSJ65ffEP3nZKIAlSSISQL+/bXtMDVtakVGsv1k1
w4IdACf3GqbjHig4mOX0oW7IwtyfBY+0q3udY28ASW0ujsH9qHE=
=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
This replaces the platform_device_add_properties() call with
the safer device_create_managed_software_node() that does
exactly the same, but can also guarantee that the lifetime
of the node that is created for the device is tied to the
lifetime of device itself.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210204141711.53775-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver may in some special cases need to copy small amounts
of payload data to a bounce buffer in order to meet the boundary
and alignment restrictions set by the xHCI specification.
In the majority of these cases the data is in a sg list, and
driver incorrectly assumed data is always in urb->sg when using
the bounce buffer.
If data instead is contiguous, and in urb->transfer_buffer, we may still
need to bounce buffer a small part if data starts very close (less than
packet size) to a 64k boundary.
Check if sg list is used before copying data to/from it.
Fixes: f9c589e142d0 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210203113702.436762-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older ATF does not provide SMC call for USB 3.0 phy power on functionality
and therefore initialization of xhci-hcd is failing when older version of
ATF is used. In this case phy_power_on() function returns -EOPNOTSUPP.
[ 3.108467] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 3.117250] phy phy-d0018300.phy.0: phy poweron failed --> -95
[ 3.123465] xhci-hcd: probe of d0058000.usb failed with error -95
This patch introduces a new plat_setup callback for xhci platform drivers
which is called prior calling usb_add_hcd() function. This function at its
beginning skips PHY init if hcd->skip_phy_initialization is set.
Current init_quirk callback for xhci platform drivers is called from
xhci_plat_setup() function which is called after chip reset completes.
It happens in the middle of the usb_add_hcd() function and therefore this
callback cannot be used for setting if PHY init should be skipped or not.
For Armada 3720 this patch introduce a new xhci_mvebu_a3700_plat_setup()
function configured as a xhci platform plat_setup callback. This new
function calls phy_power_on() and in case it returns -EOPNOTSUPP then
XHCI_SKIP_PHY_INIT quirk is set to instruct xhci-plat to skip PHY
initialization.
This patch fixes above failure by ignoring 'not supported' error in
xhci-hcd driver. In this case it is expected that phy is already power on.
It fixes initialization of xhci-hcd on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for USB 3.0 phy power.
This is regression introduced in commit bd3d25b07342 ("arm64: dts: marvell:
armada-37xx: link USB hosts with their PHYs") where USB 3.0 phy was defined
and therefore xhci-hcd on Espressobin with older ATF started failing.
Fixes: bd3d25b07342 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
Cc: <stable@vger.kernel.org> # 5.1+: f768e718911e: usb: host: xhci-plat: add priv quirk for skip PHY initialization
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # On R-Car
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # xhci-plat
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210201150803.7305-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check the following endpoints after finding the endpoint
wanted to drop.
Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612255104-5363-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sa1111_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/20201126114724.2028511-1-u.kleine-koenig@pengutronix.de
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
For those unchecked endpoints, we don't allocate bandwidth for
them, so no need free the bandwidth, otherwise will decrease
the allocated bandwidth.
Meanwhile use xhci_dbg() instead of dev_dbg() to print logs and
rename bw_ep_list_new as bw_ep_chk_list.
Fixes: 1d69f9d901ef ("usb: xhci-mtk: fix unreleased bandwidth data")
Cc: stable <stable@vger.kernel.org>
Reviewed-and-tested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1612159064-28413-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive a transfer event indicating that an endpoint should be
halted, but current endpoint state doesn't match it, then the halt might
be just resolved by the stop endpoint completion handler that detects the
halted endpoint due to a context state error.
In this case the TD we halted on is already moved to the cancelled TD list,
and should not be successfully completed and given back anymore.
Let the stop endpoint completion handler reset the endpoint, and then let
the reset endpoint handler give back the cancelled TD among all other
ones on the cancelled TD list
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint can be detected both when transfer events complete, and
in stop endpoint command completion. Both these handlers will start
clearing up the halted endpoint and queue a reset endpoint command.
It's possible to get both events for the same halted endpoint if right
after a URB cancel queues a stop endpoint command the endpoint stalls.
Use the EP_HALTED flag to prevent resetting the endpoint twice.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state()
functions with one combined function.
These function were always called after each other, and had a lot of extra
code just to pass the newly found dequeue state from the first function
to the other.
The new function also returns error in case there is a failure to
queue the new dequeue state. This way the caller can decide on
recovery measures to handle it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle race where a stop endpoint command fails with "context state error"
as hardware hasn't actually started the ring yet after a previous urb
cancellation completed and restarted the endpoint.
Flushing the doorbell write that restart the endpoint reduced these cases,
but didn't completely resolve them.
Check if the ring is running in the stop endpoint completion handler, and
issue a new stop endpoint command in this case.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci 4.6.9: "A busy endpoint may asynchronously transition from the
Running to the Halted or Error state due to error conditions detected
while processing TRBs. A possible race condition may occur if software,
thinking an endpoint is in the running state, issues a Stop Endpoint
Command, however at the same time the xHC asynchronously transitions
the endpoint to the Halted or Error state. In this case, a Context
State Error may be generated for the command completion. Software
may verify that this case occurred by inspecting the EP State for
Halted or Error when a Stop Endpoint Command results in a Context
State Error."
Halted endpoints were not detected or handled at all in the stop endpoint
completion handler. A set TR Deq ptr command was bluntly queued instead
of resetting the endpoint first. The set TR Deq command would fail with
a context state error.
Fix this case by resetting the halted endpoint first to get it to a
stopped state instead of the halted (error) state.
Handle cancelled TDs once endpoint reset completes,
invalidating cancelled TDs on ring either by turning them to no-op,
or in case ring stopped on cancelled TD then move hardware dequeue pointer
past it, which will clear the cancelled TD from hw cache, and make sure
HW does not process it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6a8 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Halted endpoints can be discoverd both when handling transfer events and
command completion events. Move code that handles halted endpoints before
both of those event handlers.
Rename the function to xhci_handle_halted_ep() to better describe
what it does. Try to reserve "cleanup" word in function names for last
stage cleanup activities.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor handler for stop endpoint command completion. Yank out the part
that invalidates cancelled TDs and turn it into a separate function.
Invalidating cancelled TDs should be done while the ring is stopped,
but not exclusively in the stop endpoint command completeion handler.
We will need to invalidate TDs after resetting endpoints as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use the existing xhci_td_cleanup() to give back cancelled TDs when a
ring is stopped.
A minor change to make sure we don't try to remove an already removed
td from the list is needed as cancelled TDs are already removed from the
td_list immediatelty when it's cancelled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a separate helper function to issue reset endpont commands
to clear halted endpoints.
This is useful for cases where a halted endpoint is discovered while
completing another command, and the endpoint halt needs to be cleared
with a endpoint reset first.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop endpoint command fails with "context state error" if the endpoint is
already stopped.
This case was observed when a previous URB cancel had just completed and
rang the doorbell to restart the ring, when a new URB cancel queued a stop
endpoint command.
>From xHC hardware pov the endpoint had not yet started, so the stop
endpoint command failed with context state error.
Right after this the doorbell ring took effect and ring was restarted.
Interrupt handler saw a stop endpoint command completion event with
"context state error" and discovered that the ring was back up in
running state.
flushing the write reduces these cases in stress testing, but does not
completely remove the issue.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
