IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit dbe678f6192f27879ac9ff6bc7a1036aad85aae9 ]
At iMX8QM platform, enable NCM gadget and run 'iperf3 -s'.
At host, run 'iperf3 -V -c fe80::6863:98ff:feef:3e0%enxc6e147509498'
[ 5] 0.00-1.00 sec 1.55 MBytes 13.0 Mbits/sec 90 4.18 KBytes
[ 5] 1.00-2.00 sec 1.44 MBytes 12.0 Mbits/sec 75 4.18 KBytes
[ 5] 2.00-3.00 sec 1.48 MBytes 12.4 Mbits/sec 75 4.18 KBytes
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Force trb_burst_size to 16 can fix this problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230518154946.3666662-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce49449e04ff150838a31386ee65917beb9ebb5 ]
Some devices have USB compositions which may require multiple endpoints.
To get better performance, need bigger CDNS3_EP_BUF_SIZE.
But bigger CDNS3_EP_BUF_SIZE may exceed total hardware FIFO size when
multiple endpoints.
By introducing the check_config() callback, calculate CDNS3_EP_BUF_SIZE.
Move CDNS3_EP_BUF_SIZE into cnds3_device: ep_buf_size
Combine CDNS3_EP_ISO_SS_BURST and CDNS3_EP_ISO_HS_MULT into
cnds3_device:ep_iso_burst
Using a simple algorithm to calculate ep_buf_size.
ep_buf_size = ep_iso_burst = (onchip_buffers - 2k) / (number of IN EP +
1).
Test at 8qxp:
Gadget ep_buf_size
RNDIS: 5
RNDIS+ACM: 3
Mass Storage + NCM + ACM 2
Previous CDNS3_EP_BUF_SIZE is 4, RNDIS + ACM will be failure because
exceed FIFO memory.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220509164055.1815081-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: dbe678f6192f ("usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b46a6b09fa056042a302b181a1941f0056944603 ]
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5dcc33677d7415c5f23b3c052f9e80cbab9ea4e ]
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8be ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d602f30149a117eea260208b1661bc404c21dfd ]
BUG: KFENCE: use-after-free read in __list_del_entry_valid+0x10/0xac
cdns3_wa2_remove_old_request()
{
...
kfree(priv_req->request.buf);
cdns3_gadget_ep_free_request(&priv_ep->endpoint, &priv_req->request);
list_del_init(&priv_req->list);
^^^ use after free
...
}
cdns3_gadget_ep_free_request() free the space pointed by priv_req,
but priv_req is used in the following list_del_init().
This patch move list_del_init() before cdns3_gadget_ep_free_request().
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Faqiang Zhu <faqiang.zhu@nxp.com>
Link: https://lore.kernel.org/r/20220608190430.2814358-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78acd4ca433425e6dd4032cfc2156c60e34931f2 ]
Clang warns:
drivers/usb/cdns3/cdns3-gadget.c:2290:11: error: variable 'priv_dev' is uninitialized when used here [-Werror,-Wuninitialized]
dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
^~~~~~~~
include/linux/dev_printk.h:155:18: note: expanded from macro 'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:167:7: note: expanded from macro 'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~
include/linux/dynamic_debug.h:152:56: note: expanded from macro '_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dynamic_debug.h:134:15: note: expanded from macro '__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/usb/cdns3/cdns3-gadget.c:2278:31: note: initialize the variable 'priv_dev' to silence this warning
struct cdns3_device *priv_dev;
^
= NULL
1 error generated.
The priv_dev assignment was moved below the if statement to avoid
potentially dereferencing ep before it was checked but priv_dev is used
in the dev_dbg() call.
To fix this, move the priv_dev and comp_desc assignments back to their
original spot and hoist the ep check above those assignments with a call
to pr_debug() instead of dev_dbg().
Fixes: c3ffc9c4ca44 ("usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()")
Link: https://github.com/ClangBuiltLinux/linux/issues/1680
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3ffc9c4ca44bfe9562166793d133e1fb0630ea6 ]
If 'ep' is NULL, result of ep_to_cdns3_ep(ep) is invalid pointer
and its dereference with priv_ep->cdns3_dev may cause panic.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Andrey Strachuk <strochuk@ispras.ru>
Link: https://lore.kernel.org/r/20220718160052.4188-1-strochuk@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b3fa25de31fb7e9afebe9599b8ff32eda13d7c94 upstream.
Path fixes bug which occurs during resetting endpoint in
__cdns3_gadget_ep_clear_halt function. During resetting endpoint
controller will change HW/DMA owned TRB. It set Abort flag in
trb->control and will change trb->length field. If driver want
to use the aborted trb it must update the changed field in
TRB.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220329084605.4022-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b69ec50b3e55c4b2a85c8bc46763eaf330605847 ]
For DEV_VER_V3 version there exist race condition between clearing
ep_sts.EP_STS_TRBERR and setting ep_cmd.EP_CMD_DRDY bit.
Setting EP_CMD_DRDY will be ignored by controller when
EP_STS_TRBERR is set. So, between these two instructions we have
a small time gap in which the EP_STSS_TRBERR can be set. In such case
the transfer will not start after setting doorbell.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org> # 5.12.x
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210907062619.34622-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d6eef886903c4bb5af41b9a31d4ba11dc7a6f8e8 upstream.
ZLP gets stuck if TDL_CHK bit is set and TDL_FROM_TRB is used
as TDL source for IN endpoints. To fix it, TDL_CHK is only
enabled for OUT endpoints.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Link: https://lore.kernel.org/r/1621263912-13175-1-git-send-email-sparmar@cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07adc0225484fc199e3dc15ec889f75f498c4fca ]
When cdns3_gadget_start() fails, a pairing PM usage counter
decrement is needed to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210412054908.7975-1-dinghao.liu@zju.edu.cn
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
It clears trb->length as zero before preparing td, but if scatter
buffer is used for td, there are several trbs within td, it needs to clear
every trb->length as zero, otherwise, the default value for trb->length
may not be zero after it begins to use the second round of trb rings.
Fixes: abc6b579048e ("usb: cdns3: gadget: using correct sg operations")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The TRB entry TD_SIZE is the packet number for the TD (request) but not the
each TRB, so it only needs to be assigned for the first TRB during the TD,
and the value of it is for TD too.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
There is an uninitialized variable "link_trb" usage at function cdns3_ep_run_transfer.
Fixed it by initialize "link_trb" as NULL.
Fixes: 4e218882eb5a ("usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When the system goes to suspend, if the controller is at device mode with
cable connecting to host, the call stack is: cdns3_suspend->
cdns3_gadget_suspend -> cdns3_disconnect_gadget, after cdns3_disconnect_gadget
is called, it owns lock wrongly, it causes the system being deadlock after
resume due to at cdns3_device_thread_irq_handler, it tries to get the lock,
but can't get it forever.
To fix it, we delete the unlock-lock operations at cdns3_disconnect_gadget,
and do it at the caller.
Fixes: b1234e3b3b26 ("usb: cdns3: add runtime PM support")
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch fixes issue caused setting On-chip memory overflow bit in usb_sts
register. The issue occurred because EP_CFG register was set twice
before USB_STS.CFGSTS was set. Every write operation on EP_CFG.BUFFERING
causes that controller increases internal counter holding the number
of reserved on-chip buffers. First time this register was updated in
function cdns3_ep_config before delegating SET_CONFIGURATION request
to class driver and again it was updated when class wanted to enable
endpoint. This patch fixes this issue by configuring endpoints
enabled by class driver in cdns3_gadget_ep_enable and others just
before status stage.
Cc: stable@vger.kernel.org#v5.8+
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Patch removes not used variable 'length' from
cdns3_wa2_descmiss_copy_data function.
Fixes: 141e70fef4ee ("usb: cdns3: gadget: need to handle sg case for workaround 2 case")
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The scatter buffer list support earlier than DEV_VER_V2 is not
good enough, software can't know well about short transfer for it.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add sg case for workaround 2, the workaround 2 is described at the
beginning of this file.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Judge each TRB has been handled at cdns3_trb_handled, since
the DMA pointer may be at the middle of the TD, we can't consider
this TD has finished at that time.
- Calculate req->actual according to finished TRBs.
- Handle short transfer for sg list use case correctly. When the
short transfer occurs, we check OUT_SMM at TRB to see if it is
the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For sg buffer list use case, we need to add ISP for each TRB, and
add CHAIN bit for each TRB except for the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It only dumps the first TRB per request, it is not useful if only dump
the first TRB when there are several TRBs per request. We improve it by
dumpping all TRBs per request in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It needs to use request->num_mapped_sgs to indicate mapped sg number,
the request->num_sgs is the sg number before the mapping. These two
entries have different values for the platforms which iommu or
swiotlb is used. Besides, it needs to use correct sg APIs for
mapped sg list for TRB assignment.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If cdns3_gadget_start is failed, it never frees cdns3_device structure.
Meanwhile, there is no release function for gadget device, it causes
there is no sync with driver core.
To fix this, we add release function for gadget device, and free
cdns3_device structure at there. Meanwhile, With the new UDC core
APIs, we could work with driver core better to handle memory leak
issue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After commit f4cfe5ce607d ("usb: cdns3: gadget: improve the
set_configuration handling"), the software will inform the
hardware the request has finished at cdns3_ep0_complete_setup.
The configuration set bit is only set after request has finished,
so it needs to move waiting operation after that. Meanwhile,
if it is timeout, it will show warning message and return error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is meaningless to handle any interrupts after disconnecting
with host
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS (.pullup is cleared) is set, the threaded irq
may be scheduled at that time.
Cc: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch split function cdns3_drd_switch_gadget and
cdns3_drd_switch_host into:
- cdns3_drd_host_on
- cdns3_drd_host_off
- cdns3_drd_gadget_on
- cdns3_drd_gadgett_off
These functions don't have any shared code so it's better to
have smaller, faster and easier functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
- Move cdns3_allow_enable_l1 into cdns3_set_hw_configuration since
it is part of this function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mainline misspelled function argument descriptions. Also one
formatting issue with a missing '@' identifier.
Fixes the following W=1 build warnings:
drivers/usb/cdns3/gadget.c:653: warning: Function parameter or member 'priv_ep' not described in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:653: warning: Excess function parameter 'priv_dev' description in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:1088: warning: Function parameter or member 'request' not described in 'cdns3_ep_run_transfer'
drivers/usb/cdns3/gadget.c:2574: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2574: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2898: warning: Function parameter or member 'priv_dev' not described in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:2898: warning: Excess function parameter 'cdns3' description in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:3210: warning: Function parameter or member 'cdns' not described in 'cdns3_gadget_init'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If it is 'int', it can't stands for the highest bit for 32-bit
number, since the largest 'int' is 0x7fffffff.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported by Coverity scan, and fixed it by declare the reg as
unsigned long.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OiS0
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
Assign interrupt number to USB gadget structure.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200402123837.5850-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
